AI 003GMK381Radio Replacement 1990-2012 Gm Dash Kit Instruction Manual
- June 4, 2024
- Ai
Table of Contents
- AI 003GMK381Radio Replacement 1990-2012 Gm Dash Kit
- VEHICLE APPLICATIONS
- DASH DISASSEMBLY INSTRUCTIONS
- DASH DISASSEMBLY
- DASH DISASSEMBLY
- SINGLE ISO MOUNT INSTALLATION INSTRUCTIONS
- DOUBLE DIN MOUNT INSTALLATION INSTRUCTIONS
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
AI 003GMK381Radio Replacement 1990-2012 Gm Dash Kit
VEHICLE APPLICATIONS
Buick
2005-07 TERRAZA
Chevy
- 2005-13 CORVETTE
- 2005-08 UPLANDER
Hummer
- 2005-10 H3
- 2009-10 H3T
Pontiac
2005-06 MONTANA SV6
Saturn
- 2005-07 RELAY
- 2005-07 BUICK TERRAZA / 2005-08 CHEVY UPLANDER
- 2005-06 PONTIAC MONTANA SV& / 2005-07 SATURN RELAY
DASH DISASSEMBLY INSTRUCTIONS
- Carefully unclip the trim from around the radio/Climate controls and remove. (Use of a panel removal tool, or a right angle scribe tool is recommended).
- Remove the (8) 9/32 or Phillips screws securing the Radio and Climate controls to the sub-dash.
- Pull the Radio and Climate controls forward, lower and set the climate control out of the way, disconnect the wire harnesses and antenna lead from the rear of the factory radio and remove radio.
2005-10 HUMMER H3/ 2009-10 HUMMER H3T
DASH DISASSEMBLY
- Carefully remove trim from around radio.
- Remove (4) 9/32 screws securing factory radio and climate controls to the sub-dash
- Lay climate controls out of the way.
- Pull radio and climate controls forward, disconnect all harnesses from radio and remove radio.
2005-12 CHEVROLET CORVETTE
DASH DISASSEMBLY
- Carefully lift up and remove the Ride Control switch/ cover plate located at the base of the center console, behind the Shifter.
- Remove the (2) 9/32 screws located beneath the Ride Control/cover plate.
- Carefully unfasten and remove the entire Radio/Climate Control trim bezel.
- Remove the (4) 9/32 screws securing the radio to the sub-dash.
- Pull the radio forward, disconnect all attached harnesses and antenna lead and remove radio.
SINGLE ISO MOUNT INSTALLATION INSTRUCTIONS
- Insert ISO brackets to rear of kit as shown in Figure A (Pg 3).
- Insert pocket into lower section of kit from rear & lock into slots of mounting brackets.
- Insert ISO mountable radio between ISO mount brackets and loosely attach to sides of radio using screws provided with radio when possible or screws supplied with kit.
- Slide radio forward or backward for desired look and tighten screws.
- Attach a rear support bracket to the rear of the new radio and adjust as necessary to support the weight of the radio (Optional)
DOUBLE DIN MOUNT INSTALLATION INSTRUCTIONS
- Remove center rib shown in Fig. B for double DIN radios only.
- Attach left and right mounting brackets to the kit as shown in Figure C.
- Insert ISO mountable radio between ISO mount brackets and loosely attach to sides of radio using screws provided with radio when possible or screws supplied with kit.
- Slide radio forward or backward for desired look and tighten screws.
- Support the rear of the radio component with back strap (optional).
For information about other American International automotive accessories visit our website at: http://www.aius.net
2500 East Francis Street Ontario, CA 91761, U.S.A. USA Sales 800-336-6500 Canada Sales 888-922-3006 CUSTOMER HELP LINE USA 800-323-4329 Canada 800-245·8777
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>