Brook XB2 Wingman Converter USB User Guide
- June 13, 2024
- Brook
Table of Contents
Brook XB2 Wingman Converter USB \
Product Description
LED Display
| Lighting | Status |
|---|---|
| Blue LED Permanently on | The connector and the device are currently |
connected.
Blue LED Slow blinking (Once every two seconds)| Wired device is not
connected Wireless device is searching for connection…
Blue LED Fast blinking| Wireless connection mode is ON. Searching for
pairing device…
Red LED Blinking| Turbo-Remap button is being pressed
Red LED Permanently on| Entering Turbo-Remap Set- tings
Connecting to the Device
step.1
Insert Wingman XB 2 into the Xbox 360 / Xbox One console USB port. Slow
blinking of the Blue LED indicates that the connection to the console is
successful.
step. 2
Wired Connection:
Connect the Xbox 360 / Xbox One/ PS3 / PS4 / Switch Pro wired controller or
game pad to Wingman XB 2 through the USB port.
Using a X360 wireless controller:
Simply connect the wireless X360 wireless receiver to the Wingman XB 2 through
the USB port.
Using Xbox One wireless controller / Xbox One Elite Series 2 / Switch Pro
controller: Connect the Xbox One wireless controller (Bluetooth model) or
the Xbox One Elite Series 2 to the Wingman XB 2 and the controller will be
ready for use. When connecting, hold the LED buttons at the two sides of the
Wingman XB 2 for 1 second to enter wireless connection mode. Then press the
Pair button on the wireless controller to begin pairing. Fast blinking of
Blue LED indicates that pairing is in progress.
Using PS3 / PS4 wireless controller:
After completing the connection according to the instructions of the Wired
Connection, remove the USB cable, and then wake up the PS3 / PS4 / Switch Pro
wireless controller.
step. 3
Check whether the two Blue LEDs at the sides of the Wingman XB 2 are
permanently on. This indicates that the connection is completed.
Connection Pairing Supplementary Instructions
step.1
Holding the LED buttons on the two sides of the Wingman XB 2 for 1 second will
activate wireless connection pairing mode. The Wingman XB 2 will engage in
pairing with surrounding Bluetooth devices. The pairing mode will end if:
A. The connection pairing with the wireless controller is successful.
B. The connection pairing is unsuccessful after 1 minute.
C. The LED buttons are held for 1 second.
step. 2
Wireless connection records between an Xbox One wireless controller (with
Bluetooth function)/Xbox One Series 2 and the Wingman XB 2 will be erased if a
wired connection is used. Wireless connection re-pairing will be required if
wireless connection is used.
step. 3
If Xbox One Elite Series 2 controller is used, please turn off controller
profile settings to prevent interference with Wingman XB 2’s Turbo or Remap
settings. As Xbox One Elite Series 1 controller is incapable of turning off
profile settings, using Xbox One Elite Series 1 controller might result in
Remap function overlapping.
Corresponding Buttons
XB1 Elite Series2| X360| PS4/PS5|
PS3| Switch| PC
---|---|---|---|---|---
D-Pad (U/D/L/R)
Lx / Ly
Rx / Ry
A| A| ╳| ╳| B| A
B| B| ○| ○| A| B
X| X| □| □| Y| X
Y| Y| △| △| X| Y
LB| LB| L1| L1| L| LB
RB| RB| R1| R1| R| RB
LT| LT| L2| L2| ZL| LT
RT| RT| R2| R2| ZR| RT
LSB| LSB| L3| L3| L3| LSB
RSB| RSB| R3| R3| R3| RSB
MENU| START| OPTIONS| START| +| START
VIEW| BACK| SHARE /Create| SELECT| –| BACK
Xbox Guide Key| Xbox Guide Key| PS Key| PS Key| Home| Xbox Guide Key
Turbo Function Settings
The following instructions are based on the Xbox One controller. For those using other controllers, please refer to the Corresponding Buttons List.
Turbo Function Settings
Buttons that can be set as Turbo function buttons include: A, B, X, Y, LB, RB, LT, RT, LSB, RSB 10 (hereinafter referred to as FK)
Step 1. Enter setting mode:
Press VIEW + Xbox Guide, the RED LED of the Wingman XB will be permanently
on.
_ Step 2. Choosing a FK button: (e.g. Setting A as turbo function) Hold
VIEW, then press A
Step 3. Completing Setting Mode:
Release all buttons, then press MENU to save settings.
Step 4._ Exit setting mode:
Press Xbox Guide, the BLUE LED of the Wingman XB will be permanently on.
Cancelling Turbo Function
Step 1. Enter setting mode:
Press VIEW + Xbox Guide, the RED LED of the Wingman XB 2 will be
permanently on.
Step 2. Erasing all Turbo function buttons Press VIEW + MENU
Step 3. Exit setting mode:
Press Xbox Guide, the BLUE LED of the Wingman XB 2 will be
permanently on.
Turbo Frequency Setting
The following instructions are based on the Xbox One controller. For those using other controllers, please refer to the Corresponding Buttons List.
Step 1. Enter the setup mode
Press VIEW + Xbox Guide, the RED LED of the Wingman XB 2 will be
permanently on.
_ Step 2. Turbo Frequency Setting
The Up button increases frequency while the Down button decreases it.
To increase frequency: press both VIEW and the Up buttons, and the indicator
will flash faster.
To decrease frequency: press both VIEW and Down buttons, then the indicator
will flash slower.
Step 3. Save
Press MENU to save your settings.
Step 4. Exit_
Press the Xbox Guide button to leave Turbo setup mode. The RED LED
indicator will then turned off.
Button Remap Settings
The following instructions are based on the Xbox One controller. For those using other controllers, please refer to the Corresponding Buttons List.
Button Remap Settings
Buttons that can be Remap include: A, B, X, Y, LB, RB, LT, RT, LSB, RSB 10 (hereinafter referred to as FK)
Step 1. Enter setting mode:
Press MENU + Xbox Guide, the RED LED of the Wingman XB 2 will be
permanently on.
Step 2. Choosing a FK button: (e.g. Setting X as A+B) Press X
Step 3. Choosing button to be set:
Hold VIEW, then press A + B.
Step 4. Completing setting mode:
Release all buttons, then press MENU to save settings.
_ Step 5. _Exit setting mode:
Press Xbox Guide, the BLUE LED of the Wingman XB 2 will be permanently on.
Cancelling Button Remap Settings
Step 1. Enter setting mode:
Press MENU + Xbox Guide, the RED LED of the Wingman XB 2 will be
permanently on.
_ Step 2. Erasing all settings for Button Remap Settings.
Press VIEW + MENU.
Step 3. _Exit setting mode:
Press Xbox Guide, the BLUE LED of the Wingman XB 2 will be permanently on.
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- Ambient Operating Temperature ………………….0℃ to +50℃
IC Statement
his device complies with Canada Industry licence-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference; and
- this device must accept any interference. Including interference that may cause undesired operation of the device.
CAN ICES-3 (B).
RF Exposure Statement: This product complies with the FCC and IC RF exposure limit set forth for an uncontrolled environment and is safe for intended operation as described in this manual.
Customer Support
FCC ID: 2ADKM005A
IC: 29174-ZPP0063
P/N: Wingman XB 2
M/N: ZPP0063
For the latest user guide and more information, visit our website:
www.brookaccessory.com