Brook XBOX Series XB Fighting Board Instruction Manual

Brook XBOX Series XB Fighting Board

Wire connection diagram

**J1/J9: Connecting analog stick

**

J2/J4/J13: Connecting buttons and digital joystick

As J2 and J4 have the same functions, only one of them is needed for the connection, it is recommended to use the dedicated cable “BROOK Fighting Board Cable”.

J5: LS/DP/RS ON/OFF switch

• DP Mode: (default): Joystick input corresponds to D-Pad output.
• LS Mode: Joystick input corresponds to Left 3DVR(Lx/Ly) output.
• RS Mode: Joystick input corresponds to Right 3DVR(Rx/Ry) output.

If the analog stick (J9 short circuit) and ON/OFF switch (J5: DP mode) are not needed, press the following button combinations for 3 seconds to change the joystick input mode.

J6/J6-1/J8: Connect the console

Choose one USB interface with a corresponding USB extension cable for the connection.

• When using J6 and J6-1, please double-check whether the corresponding pin order is correct.
• Improper connection may cause the fighting board to burn.

J10: Turbo function setting

Buttons available for Turbo function setting:
D-Pad, A, B, X, Y, LB, RB, LT, RT, LSB, RSB

Turbo function setting method:
Press the Turbo button and press the selected button, to activate or deactivate the Turbo function of the selected button.

Press the following button combinations to adjust Turbo speed:

• There are 5 speed modes for the Turbo function: 5, 10, 15, 20, 25 Hit/Sec.
• When the Player LED is flashing, it means that Turbo function of the pressed button has been activated.

J11: Player LED display

The operation status of the fighting board are all displayed through the Player LED. Connection of the Player LED is essential to confirm the operation status of the controller.

J14: Change of SOCD resolution modes

The product supports two SOCD resolution modes.

• Mode 1: When there is a left/right input collision, it becomes neutral. When there’ s an up/down input collision, the up is prioritized.
• Mode 2: The second input is prioritized when collisions occur.
   | Situation| Function
  ---|---|---

Mode 1

|

Left, Right collision: Neutral

Up, Down collision: Up priority

|

(← + → = Nothing) (→ + ← = Nothing) (↑+ ↓ = ↑)

(↓ + ↑ = ↑)

 |  | (← + → = →)
Mode 2| Second-Input Priority| (→ + ← = ←)

(↑ + ↓ = ↓)

 |  | (↓ + ↑ = ↑)

J3: Key lock

You can turn off the different functions that may be determined as illegal in official competitions:

1.  Turn off Guide, Menu, and View buttons.
2.  Turn off the Turbo function of all buttons.
3.  Mandatorily changing SOCD resolution to Mode 1.

When the LOCK LED is on, it means that the key function lock is on. When the LOCK LED is off, it means that the key function lock is off.

Arcade Stick layout design reference

Correspondence table of the button functions

How to switch between different consoles?

Automatic:

It can automatically detect the consoles (for X-360, X-One, and X-Series consoles). For X-Original, manual console switch is required.

Manual console switch:
After pressing and holding the button in the table below, connect the device to the game console to switch to the corresponding mode of the selected device .

Light display of device modes:

Switching between button config sets

Press the button combinations for 1 second to change to the following four sets of button configurations.

• When successfully switched, all Player LED will go dark for 1 second.

Other

The following table consists of the keywords and their abbreviations used in the description:

The following table consists of the keywords and their symbols used in the description:

References

• Brook Gaming

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>