Brook ZERO-PI Easy Fighting Board User Guide
- June 5, 2024
- Brook
Table of Contents
Easy Fighting Board
User Guide
NS / PS3 / PS2 / PS / PC(X-Input) / Retro Gaming System
USER GUIDE ver.22.01
A-C1049-200701-V1.0
Production induction
The ZERO-Pi fighting board supports to be used wired on NS/PS3/PS2/PS/ PC(X-Input)/Retro Gaming System, it also supports LED, and turbo function.
Function
Support NS/PS3/PS2/PS/ PC(X-Input)/Retro Gaming System
Full-Compatible with BROOK Fighting Cable
Different kinds of connectors for USB (USB Type-B/5-pin header connector/4-pin
header connector/4-pin)
Turbo Function
Support Player LEDs
Built-in SOCD cleaner
Effortless installation
Upgradable Firmware
How to connect
J1(J1-1/J1-2/J1-3) USB Connectors
Four USB connection selections for NS/PS3/PC(X-Input)/Retro Gaming Emulator
J2(J3) LED Display
Select J2 or J3 for Player LED
**Button configuration**
| PCB | Switch | PS3 | PS2 | PC |
|---|---|---|---|---|
| Stick in DP | D-PAD | D-PAD | D-PAD | POV |
| 1P | Y | X | ||
| 2P | X | Y | ||
| 3P | R | R1 | R1 | RE |
| 4P | L | L1 | L1 | LB |
| 1K | B | X | X | A |
| 2K | A | O | O | B |
| 3K | ZR | R2 | R2 | RT |
| 4K | ZL | L2 | L2 | LT |
| L3 | LSB | L3 | L3 | LTSB |
| R3 | RSB | R3 | R3 | RTSB |
| SELECT | SELECT | SELECT | BACK | |
| START | + | START | START | START |
| (SELECT & 3P) | ||||
| CAPTURE(SELECT & 4Th | ||||
| Home | Home | PS | PS | XBOX |
| Stick in LS | LX / LY | LX LY | LX/LY | LX/LY |
| Stick in RS | FOC /RY | RX /RY | RX /RY | RX /RY |
** J4(J13+J14) header**
According to your preference to connect Brook Fighting Board Cable to J4 or J13 + J14
**** J16 Screw Terminal
****J7(J8+J11) Turbo Key function
Turbo available buttons:, O L1, R1, L2, R2, L3, R3. According to your
preference to connect J7 or J18 + J11
How to set and clear
To set: Hold down Turbo Key + turbo available buttons
To clear: Redo the procedure above again to clear the turbo setting
When the turbo LED is on, some turbo buttons have been set.
When the turbo LED is off, no turbo buttons have been set.
When the turbo LED is flashing, the pressed button has been set turbo.
**** J12 How to switch between LS/RS/DP
Mode LS, RS, DP Emulate (For J12 DP Mode Only)
For those who don’t have LS, RS, or DP switches, it’s able to press combo keys
for 3 seconds to switch between LS, RS, and DP modes.
OPTIONS/ START + LEFT and press for 3 seconds
OPTIONS/ START + UP and press for 3 seconds (default)
OPTIONS/ START + RIGHT and press for 3 seconds
****J15 For PS/PS2
For connecting to PS/PS2
Zero-Pi Fighting Board supports auto-detect & manual to select Switch & PS3
consoles. If you want to switch mode manually, hold on the following button
then plug into consoles: 1P: PS3
1K: Switch Brook Design, LLC.
www.brookaccessory.com
Visit our website for more information and assistance
Copyright © Zeroplus Technology Co. Ltd All Rights Reserved Brook is the
registered trademark of Brook Design, LLC.
The other trademark names are the used marks, trademarks, or registered
trademarks of the corresponding companies.
http://www.brookaccessory.com/detail/53169470/