Brook ZPPA000 Pocket Auto Catch+ Smart Band Instruction Manual
- June 5, 2024
- Brook
Table of Contents
ZPPA000 Pocket Auto Catch+ Smart Band
Instruction Manual
Pair Pocket Auto Catch Plus with your phone
- Turn on your mobile Bluetooth.
- Launch the Map View of Pok~mon Go. Tap the Main Menu button.
- Tap Settings at the top right.
- Select Pok~mon Go Plus on the settings page.
- Select Pok~mon Go Plus
- Waiting for pairing. When Pok~mon Go Plus in available devices icon turns on, it means the pairing is completed.
Assemble and put on Pocket Auto Catch Plus
Notice
It’s recommended to take off the Pocket Auto Catch Plus when doing intense
activities.
How to change the mode
- Touch the red circle to switch between modes.
- Long press the red circle for 3 seconds to turn ON I turn OFF that mode.
- If Pocket Auto Catch Plus fails to pair to the device and displays “not paired”, please go to “Bluetooth” in “Settings” on the device to remove/ clear Pokemon Go Plus, then pair it again in the game.
Charge Your Pocket Auto Catch Plus
Notice
-
A full charge takes approx.
1 hour and lasts for approx. 12 hours with continuous use. And when it is fully charged, you won’t see the charging graphic. -
Standby time is approx.
48hours.
Catching/Caught Pokmon
Pokstops
Other Alerts
IMPORTANT
Pocket Auto Catch Plus may fail to pair to the device because of the update of the Pokemon Go app, and the upgrade of Android and iOS.
Tap the red circle while it is charging, and the charging icon will display.
If you don’t see the charging icon, make sure
Pocket Auto Catch Plus is placed firmly into the charging cable.
Have difficulties paired?
When your Pocket Auto Catch Plus has paired to another device, runs out of
power, or has any abnormality that it cannot be paired to your current device.
- Go to “Bluetooth” in “Settings” on the phone to remove/ clear Pokemon Go Plus.
- Go to the “Settings” in the game, exit/ clear Pokemon Go Plus.
- Then tap the red circle on Pocket Auto Catch Plus. When it pops up a new Pokemon Go Plus in the settings in the game, tap it to pair.
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation Is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, Including Interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
Interference In a residential Installation.
This equipment generates, uses, and can radiate radio frequency energy and, If
not installed and used In accordance with the instructions, may cause harmful
interference to radio communications. However, there Is no guarantee that
interference will not occur In a particular Installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on. the
user Is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment Into an outlet on a circuit different from that to which the receiver Is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment
This device has been evaluated to meet general RF exposure requirements. The
device can be used In portable exposure conditions without restriction.
http://www.zeroplus.com.tw/ad.php?id=9WxJABdr
FCC ID:2ADKMAOOO
P/N : Pocket Auto Catch Plus
M/N: ZPPA000 ZPP00SX
For more details please visit our official website at
www.brookaccessory.com
Version 202112V1
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>