BEGA 45485.1K2 Pendant Luminaire Instruction Manual

Table of Contents

The product is a suspended luminaire with a metal housing and canopy. It has a white color and is equipped with 1 steel messenger wire.
The overall length of the luminaire is approximately 1950 mm.
It has a protection conductor connection and a lampholder of type E27. The weight of the luminaire is 1.4 kg.

Installation:

Suspend the luminaire from the ceiling hook.
Make an earth connection and electrical connection to the terminals.
Insert the lamp into the lampholder.
Unscrew the glass cover and lift it.
Place the glass onto the glass support and adjust it accordingly.
Screw the glass cover onto the glass.
Press the canopy against the ceiling.
Adjust the clamping effect for different cable diameters using the knurled nut at the lower part of the canopy.

Shortening of Flex Suspension:

Note: Flex suspension can only be shortened at the canopy end.

Remove terminals from the cable.
Loosen the fixing screw at the hanger and pull out the steel wire.
Loosen screws from the cable collar.
Shorten the cable to the desired length and strip the end approximately 10 cm.
Place the cable back into the cable collar and tighten both screws. Ensure that approximately 5 mm of the cable coating protrudes out of the collar.
Lead the steel wire through the little hole in the hanger and lead it back through the fixing terminal.
Pull the steel wire tight and fix it with a screw.
Connect wires to the terminals and make sure to connect the steel wire to the earth terminal.

Maintenance:

Spares:

BEGA-45485-1K2-Pendant-Luminaire-FIG-1

Lamp

Luminaire with lampholder E 27
- Lamp output max. 1 × 60 W 45 485.1K2 inclusive BEGA LED lamp 13548 dimmable
LED 7 W 805 lm
- Colour temperature 2700 K
45 485.1K3 inclusive BEGA LED lamp 13586 dimmable
- LED 7 W 805 lm
Colour temperature 3000 K
Detailed technical and lighting data for the lamps can be found in the data sheets on our website.

Application

Pendant luminaire · indoor luminaire for free radiating and uniform light with hand-blown opal glass, satin matt, and metal housing.

Metal housing and canopy
- Colour white
Hand-blown opal glass, satin matt White flex suspension 3 × 0,75 @ with 1 steel messenger wire
- The overall length of the luminaire is approx. 1950mm
Connection terminal 2.5@
- Earth conductor connection
Lampholder E 27
- Safety class I
c – Conformity mark
- Weight: 1.4 kg

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Suspend the luminaire from the ceiling hook.
Make earth connection and electrical connection to the terminals.
Insert the lamp into the lamp holder.
Unscrew the glass cover and lift it.
Place glass onto the glass support and adjust it accordingly.
Screw the glass cover onto the glass.
Press the canopy against the ceiling.
The clamping effect for different cable diameters can be adjusted by the knurled nut at the lower part of the canopy

Shortening of flex suspension

The flex suspension can only be shortened at the canopy end.
Remove terminals from the cable.
Loosen the fixing screw at the hanger, pull out the steel wire, and loosen the screws from the cable collar.
Shorten the cable to the desired length and strip end approx. 10 cm.
Please consider these when cutting the cable to the required length.
Place the cable back into the cable collar and tighten both screws. Make sure that approx. 5 mm of the cable coating protrudes out off the collar.
Lead the steel wire through the little hole in the hanger and lead it back through the fixing terminal. Pull the steel wire tight and fix it with a screw.
Connect wires to the terminals and make sure to connect the steel wire to the earth terminal.

Relamping · Maintenance