Frontier P265v3 Fiber TV Remote Control User Manual

Quick Setup Guide Frontier remote

The following steps will guide you to quickly set-up your Frontier TV remote for your TV.

1. Turn on your TV and the Frontier STB. Make sure you can see live television

2. Locate the 3-digit code for your TV brand in the list to the right and circle the correct code
   If your TV brand is not listed, codes for additional TV brand sare listed at the back of this manual.

3.  Once you locate the brand code, press and hold the and keys together. The RED LED on the remote control will blink twice and then stay on.

4. Enter the 3-digit TV code for your TV brand using the number pad. The RED LED will blink twice and then stay on.

5. Press and release the <CH +> button repeatedly until the TV turns off. You can also “back up” by pressing the <CH -> button.

*Please note – some TVs may respond slower than others. Please allow 1 second between button presses. 6. Test that remote control is programmed for your TV

1. Turn the TV on using the key.
2. Press <VOL +> and <VOL -> to make sure that the volume keys work.
3. Press and keys.
4. If any of these keys do not work as expected, press and hold that key. Release it as soon as it works.
5. If all these keys work, press to save this TV brand code programming. The RED LED will blink 3 times and then turn off

Your Remote Control is now programmed for your TV!

Acronyms

1. RC = Remote Control
2. STB = Frontier TV Set Top Box
3. VOL = Volume
4. CH+ = Channel Up
5. CH- = Channel Down

Frontier TV Remote Control Codes for Major TV Brands
TV Brand : Code

• AOC 026
• Audiovox 035
• Coby 070
• Envision 114
• Funai 128
• Haier 146
• Hitachi 164
• Insignia 180
• JVC 193
• LG 210
• Magnavox 222
• Mitsubishi 243
• Panasonic 279
• Philips 285
• Pioneer 290
• Polaroid 294
• Proscan 302
• RCA 321
• Samsung 331
• Sansui 332
• Sanyo 333
• Sceptre 335
• Sharp 342
• Sony 352
• Sylvania 371
• Toshiba 397
• Viewsonic 418
• Vizio 424
• Westinghouse 433
• Zenith 440

Troubleshooting

• If the button does not work correctly, make sure the TV is on and go back to Step 1 of the Quick Start Guide. You can also try the Code Search Method below.
• If the , , or <A/V> buttons do not work correctly, please refer to the Key Fix Feature.
• If you think you made a mistake with programming your remote, you can always press the button and start over. The RED LED will turn off if the RC is not in programming mode.
• If you don’t press any buttons for 60 seconds, the remote control will automatically exit programming mode.
• Note, if you press the button many times and the lights on the remote control all flash rapidly, the programming attempt was not successful.
• If the Brand Search method does not work, please try the Code Search Method below, which scans the complete database for all TV codes.
• If you are still having problems programming the remote, please call 877-462-0488

Code Search Method to Program the RC
(This method could take up to 12 minutes)

1. Turn on your TV and the Frontier STB.
2.  Make sure you can see live television.
3. Press and hold the and buttons together, then release both.
   • The RED LED will blink twice and then stay on.
4. Press and hold down the button.
5. The Remote Control will try a new TV code every second, and the RED LED will blink each time a new code is sent.
6. When the TV turns off, stop pressing the play button right away.
   • Please note – some TVs may respond slower than others.
7. You can press the <CH +> or <CH -> buttons to go forward or back one TV code at a time.
8. Test that the remote control is programmed for your TV.
   • Turn the TV on using the key.
   • Press <VOL +> and <VOL -> to make sure that the volume keys work.
   • Press and .
   • If any of these keys do not work as expected, press and hold that key. Release it as soon as it works.
9. If these keys all work, press to save this TV brand code programming. The RED LED will blink 3 times and then turn off. Your Remote Control is now programmed for your TV!
10. Troubleshooting
11. If the button does not work correctly, make sure the TV is on and go back to Step 1 of the Code Search Method.
12. If the , , or <A/V> buttons do not work correctly, please refer to the Key Fix Feature.
13. If you think you made a mistake with programming your remote, you can always press the button and start over. The RED LED will turn off if the RC is not in programming mode.
14. Please Note, the Code Search Method could take up to 8 minutes, as it must go through over 500 codes. The most common codes are tried first, but you may need to press and hold for a while to locate the correct code.
15. Once you have tried all the TV codes in the remote control, the RED LED and the backlit buttons will flash 4 times rapidly, the RED LED will turn off and the remote will exit the programming mode.
16. If you are still having problems programming the remote, please call 877-462-0488

OPTIONAL FEATURES

< STB Power> Button Turns on TV and STB
Your remote has separate power buttons for the TV and STB. You can program the key to turn on/off both your TV and STB at the same time.

1. Turn both your TV and STB on.
2. Press and hold the and buttons together, then release both.
   • The RED LED will blink twice and then stay on.
3. Press 9 – 7 – 7.
   • The RED LED will blink twice and remain on.
4.  Press .
   • The RED LED will blink 3 times and then turn off.
5. Test that the key now turns on the TV and STB at the same time.
6. If you want to reset the remote so that the key controls Only the STB, follow the same steps as above but press in Step 4.

Control TV Volume Through STB

If the volume control keys don’t work with your TV, you can program the remote so that the STB will control the volume.

1. Press and hold the and buttons together, then release both.

2. The RED LED will blink twice and then stay on.

3. Press 9 – 5 – 5.

4.  The RED LED light will blink twice, and remain on.
   Press .

5. The RED LED will blink 3 times and then turn off.

6. If you want to change it back again so that volume buttons control the TV follow the same steps as above but press in Step 5.

Key Fix

If your remote control  programmed for your TV, but the , , or the <A/V> keys do not work correctly, then you can try using the Key Fix feature to fix the buttons.

1. Press and hold the and buttons simultaneously.
2. The RED LED will blink twice and then stay on.
3. Press and hold the key that does not work correctly. The remote control will try a new code every second.
4. Once the TV responds correctly, release the button.
5. Press to save the current settings and finish programming your remote control.

Reset the Remote Control Original Settings

1. Press and hold the and buttons together, and release.
2. The RED LED will blink twice and then stay on.
3. Press 9 – 0 – 0.
4. The RED LED will blink 3 times and then turn off to indicate original settings are restored.
5. CAUTION, all previous programming in the remote control will be lost if you follow this procedure.

General Instructions

1. Make sure the remote control has a clear, unobstructed view of the STB and TV.
2. Your Frontier TV remote control will only operate your Frontier TV STB and your TV.
3. The remote will not operate other devices like DVD Player or Audio Receiver.
4. The ,<VOL +>, <VOL ->, and <A/V> buttons will always control your TV.
5. All other keys on the remote control will always control your Frontier TV STB.

Getting Started

1. Turn on your TV and the STB using the and buttons.
2. If you have just watched a DVD, make sure your TV is set to the correct A/V Input for your STB.
3. Press the <CH +>,or <CH -> buttons to see the next higher or lower channel.
4. You can go directly to any channel by entering the channel number on the number pad and pressing .
5. Press to see a list of TV programs.
6. Press to return to TV watching.
7. Press the button to launch the Frontier TV Main Menu. From the Main Menu you can access all the features of your Frontier TV service.
8. Press keys to navigate through the Frontier CC TV Menus and Guides. To select any item, press .
9. Press to return to the last channel.
10. Press to see information about the current program.
11. Press to return to the previous menu option or to watch TV.

New and Special Buttons

1. “On Demand” displays a list of movies and other programs you can watch at any time.
2. “Widgets” displays local weather, traffic, and other information.
3. displays your list of recorded programs if you have DVR service.
4. “Favorites” displays your list of favorite channels.
5. is a rocker button. Press lower half of the button to pause the program. Press upper half of the button <►> to continue to play from where you left off.
6. jumps back 30 seconds in the program you are watching.
7. jumps forward 30 seconds in the program you are watching.
8. records the current program.
9. Buttons , and will only operate during normal TV watching if you have DVR service.
10. “If the RED LED starts blinking 5 times rapidly when you press the <CH +/->, <VOL +/->, and , or if the buttons stop lighting up, you should replace the remote control  batteries”

COMPLETE LIST OF TV BRAND CODES

TV Brand : Code

• A.R. Systems 001
• Abex 002
• ABS 003
• Accurian  600
• Acer 441
• Action 004
• Admiral 442
• Advent 005
• Adventura 006
• Aftron 007
• Aiko 443
• Aim 008
• Aiwa 009
• Akai 010
• Akiba 011
• Akira 012
• Akura 601
• Alaron 013
• Alba 444
• Albatron  602
• Alfide  016
• Alienware 017
• Alleron  445
• Allstar 446
• A-Mark 018
• Ambassador 019
• America Action 020
• Ampro 021
• Amstrad 022
• Amtron 023
• Anam 604
• Anam National 024
• Anhua 025
• Anitech 447
• Ansonic 026
• Anthem 448
• AOC 028
• Aomni 605
• Apex Digital 449
• Apple 029
• Archer 030
• Archos 031
• Aristona 032
• Asberg 033
• Astar 034
• Atlantic 450
• Audiosonic 035
• Audio-Technica 451
• Audiovox 036
• Aurora Systems 037
• Aventura 606
• Axion 452
• Baile 038
• Bang & Olufsen 039
• Basic Line 607
• Vidikron 416
• Vidtech 417
• Viewsonic 418
• Viking 419
• Villain 553
• Viore  420
• Visa 554
• Visart 555
• Visco 421
• Vision  422
• Vistron 556
• Vito 423
• Vizio 424
• Voodoo 694
• Vortec 425
• Voxson 426
• VU 695
• Waltham 427
• Wards 428
• Warumaia 696
• Watson 429
• Waycon 430
• Wega 431
• Weltblick 432
• Westinghouse 433
• Wharfedale 697
• White Westinghouse 434
• WinBook 557
• Wyse 558
• XR-1000 559
• Xrypton 435
• Yamaha  436
• Yamishi 437
• Yapshe 698
• Yokan 438
• Yoko 439
• Zenith 440
• Zonda 560
• ZT Group 699

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>