Arrows HOBBY 1300mm Arrow RC Bigfoot Instruction Manual

June 4, 2024
Arrows HOBBY

Arrows HOBBY 1300mm Arrow RC Bigfoot

Arrows HOBBY 1300mm Arrow RC Bigfoot logo

Warning
As this model aircraft is a sophisticated hobby product, it must be flown with safety and common sense in mind, failure in doing so may result in injury or property damage. This product is not intended for use by children without direct adult supervision.

S afety precautions and warnings
As the user, you are solely responsible for the safe operation and maintenance of this product. Follow the directions and warnings listed in this manual, as well as that of supporting equipment chargers, batteries etc and always use common sense. This is not a toy. Not for children under 14 years of age.

  • Always operate your model in an open area away from buildings, cars, traffic or people.
  • Never operate near people-especially children who can wander unpredictably.
  • Never operate in populated areas for any reason, where injury or damage can occur.
  • Always keep a safe distance in all directions around your model to avoid collisions or injury.
  • This model is controlled by a radio signal subject to interference from many sources outside your control.
  • Interference can cause momentary loss of control.
  • Never catch the aircraft while it is in flight, the structure of the fuselage was not designed and protected for this purpose.
  • Never operate your model in bad weather, including in excessively windy or precipitating conditions.
  • Never operate your model with low transmitter batteries.
  • Keep your throttle quadrant in its lowest position prior and after every flight.
  • Use the throttle cut function if able.
  • Always use fully charged batteries and move batteries before disassembly.
  • Avoid water exposure to all equipment not specifically designed and protected for this purpose.
  • Avoid cleaning this product with chemicals.
  • Never lick or place any part of your model in your mouth as it could cause serious injury or even death.
  • Keep all chemicals, small parts and anything electrical out of the reach of children.

Introduction

As a do-it-all multi purpose aircraft, the Arrows Hobby Bigfoot has amazing features found on a whole multitude of aircraft. In terms of flight characteristics, Bigfoot is trainer-like and easy to handle. It also has bush plane genes, with oversized flaps that give unbelievable low and slow performance (takes off within 3 meters and flies on 1/3 throttle) and giant tundra tires for all terrain performance. If you are a fan of scale, you’ll love the landing, navigation and strobe lights along with the eye catching red trim scheme. Designed to be easily assembled, Bigfoot features a completely screw-together design, taking mere minutes to assemble for experienced pilots. Go where no plane has gone before with the Arrows Hobby Bigfoot!

Features

  • Power system: 30A ESC, 3536-850KV motor, 6x 9g servos
  • Unmatched STOL performance for bush flying!
  • Landing, navigation and strobe lights
  • Screw-together assemble
  • Functional flaps
  • EPO construction

Specifications

Wingspan 1300mm(51.1in)
Overall length 1060mm(41.7in)
Flying weight ~ 1310g
Motor size 3536-KV850
Wing load 44.4g/dm² 0.12oz/in²
Wing area 29.5dm² (457.25sq.in)
Prop size 11*7, 2 blades
ESC 30A
Servo 9g Servo x 6
Recommended battery 11.1V 2200mAh 25C

Kit contents

Before assembly, please inspect the contents of the kit. The photo below details the contents of the kit with labels. If any parts are missing or defective, please identify the name or part number  then contact your local shop.

Arrows HOBBY 1300mm Arrow RC Bigfoot 1

  • A: Fuselage
  • B: Main wing set
  • C: Horizontal stabilizer
  • D: Vertical stabilizer
  • E: Antenna
  • F: Wing spar
  • G: Propeller and spinner set
  • H: Screws and pushrods
  • I: Y-harnesses and body clips
  • J: Landing gear set

Model assembly

Landing gear installation

With the fuselage inverted, align the landing gear and plastic fairing with the slot in the fuselage.Arrows HOBBY 1300mm Arrow RC Bigfoot
2

Secure the assembly using the included screws.

Horizontal and vertical stabilizer installation

Align the horizontal stabilizer onto the fuselage.

Arrows HOBBY 1300mm Arrow RC Bigfoot 4

Model assembly

Arrows HOBBY 1300mm Arrow RC Bigfoot 5

Using the included double sided tape, adhere the vertical stabilizer to the fuselage.

Arrows HOBBY 1300mm Arrow RC Bigfoot 6With the fuselage inverted, secure the installed horizontal and vertical stabilizers to the fuselage using the included HKM 3.0x26mm screws. Secure the rudder pushrod using the KA2.0x12mm screws.

Wing installation

Slide the two wing halves onto the wing spar.

Arrows HOBBY 1300mm Arrow RC Bigfoot 7

Connect the flap servos, then the aileron servos using the included Y harnesses. Secure the wing set using included screws. Connect the LED controller to receiver.

Arrows HOBBY 1300mm Arrow RC Bigfoot 8

Install the wing struts onto the fuselage and secure using the included body clips.

Arrows HOBBY 1300mm Arrow RC Bigfoot 9

Antenna installation

Adhere the antenna to the wing surface using the indicated adhesive. Required Adhesives: Medium CA

Arrows HOBBY 1300mm Arrow RC Bigfoot 10

Pushrod installation

Connect the horizontal stabilizer pushrod to the control horn as shown.

2.Connect the vertical stabilizer pushrod to the control horn.

Arrows HOBBY 1300mm Arrow RC Bigfoot 12

Propeller installation

Assemble the spinner and propeller as shown. Note the motor should rotate clockwise when viewing the plane from the rear.

Arrows HOBBY 1300mm Arrow RC Bigfoot 13

Battery installation

Arrows HOBBY 1300mm Arrow RC Bigfoot 14

  1. Remove the battery cover.
  2. Remove the hook and loop tape from the fuselage.
  3. Apply the looped surface to the battery.
  4. Install the battery into the fuselage securing it with the preinstalled battery straps.

Note
The weight of each battery may vary due to different manufacturing techniques. Move the battery fore or aft to achieve the optimal center of gravity.

Receiver diagram

The cables from the servo connector board should be connected to your receiver in the order shown. Note that the LEDs can be powered by any spare channel on the receiver. Tuck the wire leads into the recessed cavity towards the rear of the battery hatch.

Arrows HOBBY 1300mm Arrow RC Bigfoot 15

Preflight check

Important ESC and model information
  1. The ESC included with the model has a safe start.
  2. If the motor battery is connected to the ESC and the throttle stick is not in the low throttle or off position, the motor will not start until the throttle stick is moved to the low throttle or off position.
  3. Once the throttle stick is moved to the low throttle or off position, the motor will emit a series of beeps. Several beeps with the same tune means the ESC has detected the cells of the battery.
  4. The count of the beeps equals the cells of the battery.
  5. The motor is now armed and will start when the throttle is moved.
  6. The motor and ESC come pre-connected and the motor rotation should be correct.
  7. for any reason the motor is rotating in the wrong direction, simply reverse two of the three motor wires to change the direction of rotation.
  8. The motor has an optional brake setting.
  9. The ESC comes with brake switched off and we recommend that the model be flown with the brake off.
  10. However, the brake could be accidentally switched on if the motor battery is connected to the ESC while the throttle stick is set at full throttle.
  11. To switch the brake off, move the throttle stick to full throttle and plug in the motor battery.
  12. The motor will beep one time. Move the throttle stick to low throttle or the off position. The motor is ready to run and the brake will be switched off.
  13. Battery Selection and Installation.
  14. We recommend the 11.1V 2200mAh 25C Li-Po battery.
  15. If using another battery, the battery must be at least a 11.1V 2200mAh 25C battery.
  16. Your battery should be approximately the same capacity, dimension and weight as the 11.1V 2200mAh 25C Li-Po battery to fit the fuselage without changing the center of gravity significantly.
Transmitter and model setup

After assembly and prior to your first flight, make sure all control surfaces respond correctly to your transmitter by referring to the diagram below.

Arrows HOBBY 1300mm Arrow RC Bigfoot 16

Control throws

The suggested control throw setting for the Bigfoot are as follows dual rate setting.

Arrows HOBBY 1300mm Arrow RC Bigfoot 21

Tip
The maiden flight should always be flown using low rates, fly the aircraft until you are familiar with its characteristics prior to trying high rates. Make sure the aircraft is flying at altitude and adequate velocity prior to using high rates, as the aircraft will be sensitive to control inputs with the larger control surface movements.

Clevis installation

Arrows HOBBY 1300mm Arrow RC Bigfoot 17

  1. Pull the tube from the clevis to the linkage.
  2. Carefully spread the clevis, then insert the clevis pin into the desired hole in the control horn.
  3. Move the tube to hold the clevis on the control horn.

Control horn and servo arm settings

  1. The table shows the factory settings for the control horns and servo arms.
  2. Fly the aircraft at the factory settings before making changes.
  3. After flying, you may choose to adjust the linkage positions for the desired control response.

Finding the center of gravity

Finding the correct center of gravity is critical in ensuring that the aircraft performs in a stable and responsive manner. Please adjust the weight distribution so the aircraft balances in the range stated on the diagram.

Depending on the capacity and weight of your chosen flight batteries, move the battery forward or backward to adjust the center of gravity.  If you cannot obtain the recommended CG by moving the battery to a suitable location, you can also install a counterweight to achieve correct CG. However, with the recommended battery size, a counterweight is not required. We recommend flying without unnecessary counterweight.

Before flying the model

Find a suitable flying site

Find a flying site clear of buildings, trees, power lines and other obstructions. Until you know how much area will be required and have mastered flying your plane in confined spaces, choose a site which is at least the size of two to three football fields – a flying field specifically for R/C planes is best. Never fly near people  especially children, who can wander unpredictably.

Performing a range check

A radio range check should be performed prior to the first flight of the day. This test may assist you in detecting electronic problems that may lead to a loss of control- problems such as low transmitter batteries, defective or damaged radio components or radio interference. This usually requires an assistant and should be done at the flying site. Always turn your transmitter on first. Install a fully charged battery in the battery bay, then connect it to the ESC. In this process, make sure that the throttle cut functionality is on, and that the throttle stick is secured in its lowest position- other-wise, the propeller/fan will engage and possibly cause bodily harm.

Note
Please refer to your transmitter manual that came with your radio control system to perform a ground range check. If the controls are not working correctly or if anything seems wrong, do not fly the model until you correct the problem. Make certain all the servo wires are securely connected to the receiver and the transmitter batteries have a good connection.

Monitor your flight time

Monitor and limit your flight time using a timer (such as a stopwatch or on the transmitter, if available). As modern Lithium Polymer batteries are not designed to discharge completely, when the battery runs low, the ESC will lower then completely cut the power to the motors to protect the battery. Often (but not always) power can be briefly restored after the motor cuts off by holding the throttle stick all the way down for a few seconds. To avoid an unexpected dead-stick landing on your first flight, set your timer to a conservative 4 minutes. When your alarm sounds you should land right away.

Flight tips

Take off

Point the aircraft into the wind while slowly applying power until the aircraft starts to track straight, use the rudder when necessary. When the aircraft reaches takeoff speed, ease back on the elevator stick until the aircraft is climbing at a constant rate without decelerating. Climbing at too steep of an angle at the relatively low speeds of a takeoff-climb may result in an aerodynamic stall.

Flying

Always choose a wide-open space for flying your plane. It is ideal for you to fly at a sanctioned flying field. If you are not flying at an approved site always avoid flying near houses, trees, wires and buildings. You should also be careful to avoid flying in areas where there are many people, such as busy parks, schoolyards, or soccer fields. Consult laws and ordinances before choosing a location to fly your aircraft. After takeoff, gain some altitude. Climb to a safe height before trying technical maneuvers.

Landing

Land the aircraft when you start to feel sluggish motor response. If using a transmitter with a timer, set the timer so you have enough flight time to make several landing approaches. The model’s three point landing gear allows the model to land on hard surfaces. Align model directly into the wind and fly down to the ground. Fly the airplane down to the ground using 1/4-1/3 throttle to keep enough energy for proper flare. Before the model touches down, always fully decrease the throttle to avoid damaging the propeller or other components. The key to a great landing is to manage the power and elevator all the way to the ground and set down lightly on the main landing gear. With some practice, you will be able to set the aircraft gently on its main gear and hold it that way until the speed reduces enough where the nose wheel (tricycle landing gear aircraft) or tail wheel (tail draggers) settles onto the ground.

Maintenance

Repairs to the foam should be made with foam safe adhesives such as hot glue, foam safe CA, and 5min epoxy. When parts are not repairable, see the spare parts list for ordering by item number. Always check to make sure all screws on the aircraft are tightened. Pay special attention to make sure the spinner is firmly in place before every flight.

Troubleshooting

Problem Possible Cause Solution
Aircraft will not respond to the throttle but responds to other controls.

ESC is not armed.

Throttle channel is reversed.

| Lower throttle stick and throttle trim to lowest settings.

Reverse throttle channel on transmitter.

Excessive vibration or propeller noise.

| Damaged spinner, propeller, motor or motor mount.

Loose propeller and spinner parts. Propellor installed backwards.

| Replace damaged parts.

Tighten parts for propeller adapter, propeller and spinner.

Remove and install propeller correctly.

Reduced flight time or aircraft  underpowered.

| Flight battery charge is low. Propeller installed backward. Flight battery damaged.| Completely recharge flight battery.

Replace flight battery and follow flight battery instructions.

Control surfaces unresponsive or sluggish.

|

Control surface, control horn, linkage or servo damage.

Wire damaged or connections loose.

|

Replace or repair damaged parts and adjust controls.

Do a check of connections for loose wiring.

Controls reversed.| Channels are reversed in the transmitter.| Do the control direction test and adjust controls for aircraft and transmitter.

Motor loses power

Motor power pulses then motor loses power.

| Damage to motor, or battery. Loss of power to aircraft.

ESC uses default soft Low Voltage Cutoff LVC.

|

Do a check of batteries, transmitter, receiver, ESC, motor and wiring for damage replace as needed.

Land aircraft immediately and recharge flight battery.

LED on receiver flashes slowly.

|

Power loss to receiver.

| Check connection from ESC to receiver. Check servos for damage.

Check linkages for binding.

Spare parts list

AHAF101 Fuselage AHAF117 LED set
AHAF102 Main wing AHAF118 LED controller
AHAF103 Horizontal stabilizer AHPROP008 Propeller
AHAF104 Vertical stabilizer AHMount001 Motor mount
AHAF105 cowl AHBoard007 Motor board
AHAF106 Battery cover AHShaft001 Motor shaft
AHAF107 Spinner AHKV850 Brushless motor 3536-KV850
AHAF108 Antenna AHESC30A 30A ESC
AHAF109 Linkage rods AHSER9GP 9g servo positive
AHAF110 Wing struts
AHAF111 R Clasp
AHAF112 Screws
AHAF113 Front landing gear set
AHAF114 Rear landing gear set
AHAF115 Wheel set
AHAF116 Sticker

Disclaimer of Warranties

  • This model must not be used by children younger than 14 years
  • It contains small parts that could be swallowed
  • Keep hands, face, hair and loose clothing away from the propeller
  • Do not reach into rotating parts
  • Always disconnect the battery connector after the flight and remove the battery
  • Only fly where it is safe and where you do not endanger third parties
  • Keep the operating instructions in a save place and read them carefully and completely before using the model.
  • We recommend people with no knowledge of model flying to commission the model under the guidance of an experienced pilot
  • Before each flight, test the range of the remote control and the charge status of the rechargeable battery and check the batteries or rechargeable batteries in the remote control.

Do not fly near crowds of people, towards people or animals, in poor visibility, near high-voltage lines or radio masts  during thunderstorms, rain, snow or in a damp environment.

  1. Always keep the aircraft in sight and under control.
  2. Always use fully charged batteries / rechargeable batteries.
  3. Always switch on model first, then transmitter, and always switch off model first, followed by the transmitter.
  4. Do not use the model if it is visually or mechanically damaged.
  5. Always check all screw connections and structures for tightness and damage.
  6. Never reach into the rotating propeller risk of injury.
  7. Always disconnect and remove the flight battery from the model after the flight.
  8. Always charge and store the battery outside of the model, charge on a non-flammable surface, never store the battery in the model.
  9. Never charge batteries unobserved.
  10. Check about the legal provisions applicable in your country

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals