BLOW BL003 Car GPS Tracker Instruction Manual
- June 10, 2024
- BLOW
Table of Contents
BLOW BL003 Car GPS Tracker User Manual
78 –630#
Product Overview
Thank you for purchasing portable GPS tracker.It’s for monitoring and protecting people and property with built–in U–blox GPS and GSM/GPRS technology.It also with strong magnet in the rear and 8000mA backup battery.
Accessories
1X Device
1X USB charge cable
1X User Guide
Hardware Specification
| Content | Specs. |
|---|---|
| Mainframe Dimension | 10456.524mm |
| Net weight | 195g |
| GSM frequencies | 850/900/1800/1900Mhz |
| GPRS | Class12,TCP/IP |
| GPS chip | UBLOX G7020 |
| Voltage range | 3.6–4.2VDC |
| Standby Current | ≤2mAh |
| GPS locating time | cold start=38s warm start=32s hot start=2s |
| GPS Accuracy | ≤ 10m |
| GPS sensitivity | –159DB |
| Work environment temperature | –40°C+80°C |
| Work environment humidity | 20%–80%RH |
| Battery | Chargeable 3.7v 8000mAh |
SIM Card Installation
The SIM card is not included in the package.Any SIM card which support GSM 2G can work and be available from the user’s local operator.
Note: Before installing the SIM card,please check if the SIM card has PIN code or not, if yes, please use a cell–phone to unlock the card’s PIN code. And make sure it’s activated with credits.
Device Charging
For the first time use,please fully charge the battery for around 2–3 hours with the USB charger.
Turn on the device by Inserting Card
Please insert the SIM card in the right direction. You will see the indicator light sparkles,then turn off.That means the SIM card inserted successfully.
After normal turn–on, the platform will upload position in 10 minutes and you can log on the website for checking.
Led indicator:
| Solid blue | Sim card inserted wrongly |
|---|---|
| Flashing blue | Searching GPS signal |
| Blue OFF | Start to work |
| Red ON | Charging the battery |
| Red off | Full charing |
Configuration and Operation by SMS
1. To Set the Authorized Number
Command : CENTER,000000,phone number#
NOTE : The letters or symbols should be English and the letters should be
in capital.
Example : CENTER,000000,123456789#
※ Using your mobile phone,send the above command to the phone number of the
device,it will reply: Center OK!
※ To delete this number,you can send :CENTER,000000,0# to the phone number of
the device.
2. GPRS Setting
In order to use the GPRS function,the user needs to setup the APN by sending
SMS command.
—what is APN? Access Point name(APN) is the name used to identify a general
packet radio service (GPRS) bearer service in the GSM mobile network. The APN
defines the type of service that is provided in the packet data connection.
※ Make sure that the SIM card in the tracker supports the GPRS function.
※ The APN can be acquired from your local GSM operators.
Command : APN,APN information,user name,password#
Note : Some APN without user name and password,so please leave it blank.
For example : APN,internet,123,456# (with the user name and password)
APN,internet# (without the user name and password) ※ please set it up when the
device can not connect with the web platform or the APP.
※ After sending the command,it will reply:APN OK!
3. Set up the SMS Language
Command : LANG,0# (English)
LANG,1# (Chinese)
※ The default language is Chinese.
※ This is to set up the language of SMS reply content.
※ after sending the command,it will reply:LANG OK!
4. Location request
4.1. Reply with coordinates and web link Command:URL#
The device will reply : the IMEI No,the date,the time,the map link,the
longitude and latitude
Example : 3568xxxxxxx2219<01–03 14:59:43>
http://maps.google.com/maps?q=N22.669534,E114.011888
※ Put the coordinates to Google earth or Google maps,click on search
button,then you will find the position.
※ Click on the link then the location can be shown directly on Google Map on
your mobile phone.
5. Vibration Alarm
Command :
VA,ON# (turn on this function)
VA,OFF# (turn off this function)
※ This function is off by default setting.
※ After sending the command,it will reply:VA OK!
6. Over–Speed Alert
Command :
OS,80# (80 is the set–up speed)
OS,OFF# (turn off this function)
※ this is to turn on/off the over–speed alarm,speed unit:km/h
※ speed range:30–180km
※ this function is off by default setting.
※ after sending the command,it will reply:OS OK!
7. Checking Settings
7.1. Command:ST#
※ The device will reply:
IMEI：888xxxxxxxxx888
MC：1(Alarm mode )
VA：0 (Vibration alarm on/ff)
OS: 0 （Over speed alarm on/off）
LA：0（Light perception alarm on/off）
HBT：10 (Heartbeat packet time)
LANG： 1（language）
GMT：E8 (time zone)
7.2. Command:QP#
※ The device will reply :
IMEI:3568XXXXXXXXX90
APN:cmnet
IP:b.gps903.net/7700
LMT,0#
CENTER:
SOC4：0
GSM:100
GPS:FIXED
BAT:3.9
8. Reboot device Command:RESET#
※ The device will restart itself without changing any settings.
9. Initialization Command:RFS#
※ This is to make all settings back to the factory default,except the IP.
※ Only the center number has the right to operate.
※ please caution to use.
10. Working Modes
Command:
WKMD,2# (super–long standby mode)
WKMD,1# (power–saving mode)
WKMD,0# (safe mode) ※ the default mode is safe mode.
※ Super–long standby mode:The platform only work when you send a SMS command
to get the location,this is the most power–saving.
※ Power–saving mode:The platform only upload LBS location and the location
precise varies according to the cities where it is located . It is purely
power-saving.
※ Safe mode:The platform will upload GPS location with high precision in real
time. But it is very power-consuming.
11. Set up data upload time interval
Command :WKMD,0#20#
※ WKMD,0# represents the safe mode
※ time can be from 20s to 120s. The time must be a multiple of 10.
※ the default is 20s
※ after sending the command,it will reply:WKMD,0:OK!
How to Connect Device to the Platform for real time tracking via GPRS
1. Check through PC
Web Platform : www.gps903.net (International)
Choice your language
Account: Device IMEI (on the device casing)
Original passwords: 123456
Operations of APP in a Cellular Phone
2. APP NAME: GPSONE
※ please search it in the IOS app store or Google play store or scan the QR
code
※ please login the app as following:
Geo Fence
An electronic fence can be set up after log–in APP or PC. Then you can check the messages from the device messages.
Cautions:
Please comply with the instructions to extend the unit life:
- Don’t use & store the unit in dusty places.
- Don’t put the unit in overheated or over cooled places.
- Clear the unit with a piece of dry cloth. Don’t Clean in chemicals,detergent.
Using other batteries will cause unwanted situation.
Made in ChRL for:
PROLECH R. i S. Leszek Sp. J.
Stary Puznów 58B
08–400 Garwolin, Poland
Electrical equipment marked with the bin icon cannot be disposed of along with ordinary municipal waste. Such equipment should be collected and recycled.
www.blow.com.pl
www.prolech.com.pl
References
- BLOW | Sklep internetowy
- BLOW | Sklep internetowy
- gps903.net/
- Prolech Importer Sprzętu Elektronicznego
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>