ILUMINAR IL-A153026-FSG-120 iL1 Power Cable Sold Seperately User Manual
- June 13, 2024
- ILuminar
Table of Contents
- ILUMINAR IL-A153026-FSG-120 iL1 Power Cable Sold Seperately
- TECHNICAL SPECS
- PHYSICAL SPECIFICATIONS
- VOLTAGE AND AMPERAGE
- MOUNTING & COVERAGE
- HARDWARE AND ACCESSORIES
- IN THE BOX
- HANGING INSTALLATION
- CONNECTION
- AVAILABLE CABLES
- GUARANTEE
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ILUMINAR IL-A153026-FSG-120 iL1 Power Cable Sold Seperately
Please read this manual thoroughly prior to installing or operating the ILUMINAR Lighting iL1.
- Observe all safety precautions (see page 12), seek the services of a qualified electrician, installation professional, or call ILUMINAR Lighting technicians for assistance.
- DO NOT handle or touch the fixture while in use.
- Connect the fixture only to the power sources of the appropriate voltage using the correct AC plug type. Protect power cables from being pinched, walked on, or otherwise damaged. Be especially careful where the power cable enters the power outlet to the unit. Only connect the fixture to an electrical outlet or extension cord of comparable standard and level rating. Connect the fixture ONLY to the power sources of the correct voltage using the plug received.
- The fixture should only be cleaned as directed. Always seek service for your system by qualified service personnel if any of the following occur:
- The fixture shows a noticeable change in performance.
- The power-supply cord or plug is damaged.
- The fixture has been dropped, or the exterior is damaged.
- MODEL:
- 2.6
- VOLTAGE:
- **** 100-277V
- WATTS:
- 530W
- 660W
- SKU:
- IL-A153026-FSG-120
- IL-A166026-FSG-120
TECHNICAL SPECS
530W 660W
| PPF | 1378 μmol/s | 1716 μmol/s |
|---|---|---|
| BTU | 1802 | 2244 |
| Efficacy | 2.6 μmol/J | |
| Min Power Factor | >0.9 | |
| THD | <20% | |
| Crest Factor | 0.99 | |
| Rated Voltage | 120-277V AC | |
| Voltage Range (+/-10%) | 100-277V | |
| Frequency | 50 / 60Hz | |
| Dimmable | 0-10V Controllable | |
| Ambient Temperature | 0 – 35°C / 32-95°F | |
| Relative Humidity | 98% | |
| Color Temperature | 4000k | |
| Color Rendering Index | 88 | |
| Minimum Mounting Height | >18” to top of Canopy | |
| Emitter Cooling | Passive Thermal Management | |
| Light Distribution +/- 5% | 125º | |
| Waterproof Rating | iP65 for Damp/Wet Conditions | |
| LED Lifespan (90% of | 54,000+ hours |
PHYSICAL SPECIFICATIONS
530W 660W
| Length | 1140mm | 44.9” | 1500mm | 59.1” |
|---|---|---|---|---|
| Width | 129mm | 5.1” | 129mm | 5.1” |
| Height | 200mm | 7.9” | 200mm | 7.9” |
| Weight | 10.2kg | 22.5lbs | 12.5kg | 27.5lbs |
VOLTAGE AND AMPERAGE
530W 660W
| Length | 1140mm | 44.9” | 1500mm | 59.1” |
|---|---|---|---|---|
| Width | 129mm | 5.1” | 129mm | 5.1” |
| Height | 200mm | 7.9” | 200mm | 7.9” |
| Weight | 10.2kg | 22.5lbs | 12.5kg | 27.5lbs |
iL1 LED SPECTRUM
MOUNTING & COVERAGE
HARDWARE AND ACCESSORIES
- The iL1 can be hung from steel cables or can be mounted to a rack. Before you begin installation, check that you have all the necessary parts to begin.
IN THE BOX
HANGING INSTALLATION
- Set the hooks on the beam.
- Hang the light into hooks.
CONNECTION
If you plan to utilize several LEDs in your room or facility, one of the many
benefits of the ILUMINAR Lighting LED is that you can “daisy chain” one
fixture to another to save space and use only one outlet to run several lamps,
thus minimizing the amount of cords used in your space. If you plan to utilize
the ILUMINAR Touch+ Controller, connect the connections from the controller to
the fixture and then connect the Daisy Chain Controller Cable from fixture to
fixture. Please consult with our lighting layout designers to ensure proper
spacing of outlets for your unique setup.
AVAILABLE CABLES
PPFD MAP iL1 530W at 1.5ft
| Clearance | 1.5 | ft |
|---|---|---|
| Qty | 1 | u |
| Average PPFD | 562.14 | μmol/m2/s |
| Max PPFD | 1171 | μmol/m2/s |
| Min PPFD | 164 | μmol/m2/s |
| Median PPFD | 476.5 | μmol/m2/s |
| Min/Average | 29.17 | % |
| Watts | 557.7 | W |
Legend
PPFD MAP iL1 530W at 4ft
| Clearance | 4 | ft |
|---|---|---|
| Qty | 1 | u |
| Average PPFD | 203.39 | μmol/m2/s |
| Max PPFD | 256 | μmol/m2/s |
| Min PPFD | 146 | μmol/m2/s |
| Median PPFD | 202.5 | μmol/m2/s |
| Min/Average | 71.78 | % |
| Watts | 557.7 | W |
Legend
PPFD MAP iL1 660W at 1.5ft
| Clearance | 1.5 | ft |
|---|---|---|
| Qty | 1 | u |
| Average PPFD | 626.34 | μmol/m2/s |
| Max PPFD | 1195 | μmol/m2/s |
| Min PPFD | 183 | μmol/m2/s |
| Median PPFD | 532 | μmol/m2/s |
| Min/Average | 29.22 | % |
| Watts | 661.2 | W |
Legend
PPFD MAP iL1 660W at 4ft
| Clearance | 4 | ft |
|---|---|---|
| Qty | 1 | u |
| Average PPFD | 252.1 | μmol/m2/s |
| Max PPFD | 320 | μmol/m2/s |
| Min PPFD | 172 | μmol/m2/s |
| Median PPFD | 251 | μmol/m2/s |
| Min/Average | 68.23 | % |
| Watts | 661.2 | W |
Legend
CAUTION
- Leave at least one inch of space between the fixture and the mounting area for maximum performance and lifespan.
- ALWAYS wear protective eyewear when looking directly at the diodes to prevent eye damage.
- Only handle, clean or move fixture when it’s unplugged and completely cool.
- Keep the fixture free of dust, debris, deposits to ensure the maximum potential of the fixture.
- NEVER use cloth to clean the diodes. This will scratch the diodes and could potentially break or dislodge them.
- DO NOT use chemicals to clean the fixture. Use ONLY low pressure air or low pressure water to remove dust and debris.
- Do NOT use sulfur vaporizers.
GUARANTEE
At ILUMINAR Lighting, we stand behind our products and our technology as well as our customers. All ILUMINAR Lighting fixtures are backed by our 5-Year Guarantee. Please visit our website iluminarlighting.com/warranty for more information.
References
- Led Grow Lights | Iluminar Lighting | Led Grow Lights | Canada
- TERMS AND CONDITIONS | ILUMINAR Lighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>