BRIO AB 0388 RC Race Car Instructions

BRIO AB 0388 RC Race Car

Battery operated play functions:

Remote-Control Race Car with age-appropriate controls and functions that are designed for toddlers. Large one- button steering system helps make racing simple and fun.
Before using the Remote-Control Race Car:

•  Install the batteries according to the picture below.
•  Switch on the car by pushing the switch button to the ON position on the bottom of the car.
•  Point the remote controller unit towards the car and race!

Keep in mind that:

•  The product is not water-resistant. Wipe off the car with a clean cloth to remove any foreign materials.
•  The child’s hair can easily get caught in moving parts.
•  The product is only recommended for indoor play.
•  The remote-control has a range of up to 15 meters
•  The car is put into sleep mode after 5 minutes of inactivity. To reactivate, just turn the car off (OFF) and restart the car (ON).

If the Remote-Control Race Car does not work properly:

1.  Try turning the car off, and then turn it on again.
2.  Change the playing surface.
3.  Make sure nothing is stuck to or in the wheels.
4. Replace the batteries.

Frequency range:

Maximum RF output power of the product: -5.8 dBm

When the child presses the top button, the race car drives straight ahead.

When the child presses the bottom button, the race car drives in reverse.

When the child presses the right button, the race car makes a narrow right- hand turn and drives around its own axis.

When the child presses the left button, the race car makes a narrow left-hand turn and drives around its own axis

With both buttons pressed, the race car makes a softer right-hand turn while driving forward.

With both buttons pressed, the race car makes a softer left-hand turn while driving forward.

With both buttons pressed, the race car makes a narrow right-hand turn while driving in reverse.

With both buttons pressed, the race car makes a narrow left-hand turn while driving in reverse.

Inserting and changing the batteries:

this remote control is powered by 3 x AA 1.5V batteries (not included). Use a screwdriver to open the battery compartment cover (see illustration). Always position new battery as shown (+/–). Close the cover and tighten the screw.

This race car is powered by 4 x AA 1.5V batteries (not included). Use a screwdriver to open the battery compartment cover (see illustration). Always position new battery as shown (+/–). Close the cover and tighten the screw.

Important

• Only adults should install and replace batteries.
•  Different types of batteries or new and used batteries are not to be mixed.
•  Only recommended batteries of the same or equivalent type as recommended (1.5V)
• re to be used.
•  Batteries are to be inserted with the correct polarity.
•  Exhausted batteries are to be removed from the toy.
•  The supply terminals are not to be short-circuited.
•  Always remove batteries if the toy is not to be used for some time.
•  Protect the toy from water or dampness.
•  Do not attempt to recharge non-rechargeable batteries.
•  Rechargeable batteries are to be removed from the toy before being charged.
•  Rechargeable batteries are only to be charged under adult supervision.
•  Used batteries and electrical components must be disposed of at an approved collection point.
•  Electrical components or batteries must not be thrown with household waste.

BRIO AB, Box 305, SE-201 23 Malmö, Sweden. Tel: +46 40 619 40 00. © 2019 BRIO AB/0388-896 D This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>