PLANET Technology GSD-1022UP SFP Desktop Gigabit PoE Switch User Manual

PLANET Technology GSD-1022UP SFP Desktop Gigabit PoE Switch

Package Contents

Thank you for purchasing PLANET 2-Port 10/100/1000T 802.3bt PoE + 4-Port 10/100/1000T 802.3at PoE + 2-Port 10/100/1000T + 2-Port 1000X SP Desktop Switch, GSD-1022UP. Open the box of the GSD-1022UP and carefully unpack it. The box should contain the following items:

If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

Hardware Introduction

Front Panel
The Front Panel of the GSD-1022UP consists of 2-Port 10/100/1000T 802.3bt PoE, 4-Port 10/100/1000T 802.3at PoE, 2-Port 10/100/1000T and 2-Port 1000X SP. The LED Indicators are also located on the front panel of the GSD-1022UP as shown in Figure 2-1.

LED Indicators

Multiple Functions of DIP Switch
The front panel of the GSD-1022UP provides one DIP switch for Legacy, BT and UPoE mode selection. The detailed descriptions are shown in the following table.

Note Please adjust the DIP switch before powering on the GSD- 1022UP.

Switch Rear Panel
Figure 2-2 shows the rear panel of the GSD-1022UP

AC Power Receptacle
Power Note The device is a power-required device, which means it will not work till it is powered. If your networks should be active all the time, please consider using UPS (uninterrupted power supply) for your device. It will prevent you from network data loss or network downtime.

Power Note In some areas, installing a surge suppression device may also help to protect the GSD-1022UP from being damaged by unregulated surge or current to the GSD-1022UP or the power adapter.

Hardware Installation

This part describes how to install the GSD-1022UP and make connections to it. Please follow the procedure below
Note : This GSD-1022UP does not need software configuration.

Desktop Installation
To install the GSD-1022UP on the desktop, simply follow these steps: Step 1: Attach the rubber feet to the recessed areas on the bottom of the GSD-1022UP as shown in Figure 3-1.

Step 2: Place the GSD-1022UP on the desktop near an AC power source.
Step 3: Keep enough ventilation space between the GSD-1022UP and the surrounding objects.

Note When choosing a location, please keep in mind the environ- mental restrictions discussed in Section 4 under Product Specifications.

Step 4: Connect the GSD-1022UP to network devices.
A. Connect one end of a standard network cable to the 10/100/1000BASE-T RJ45 ports on the front of the GSD-1022UP.
B. Connect the other end of the cable to the network devices such as printer servers, workstations or routers, etc.

Note Connection to the Switch requires UP Category 5, 5e, 6 network cabling with RJ45 tips.

Step 5: Supply power to the GSD-1022UP.

A. Connect one end of the power cable to the GSD-1022UP.
B. Connect the power plug of the power cable to a standard wall outlet.
When the GSD-1022UP receives power, the Power LED should remain solid Green. 3.2

Rack Mounting
To install the GSD-1022UP in a 19-inch standard rack, follow the instructions described below:

Step 1: Place the GSD-1022UP on a hard flat surface, with the front panel positioned towards the front side.
Step 2: Attach a rack-mount bracket to each side of the Switch with supplied screws attached to the package. Figure 3-2 shows how to attach brackets to one side of the GSD-1022UP.

Caution You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws would invalidate your warranty.

Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second bracket to the opposite side.
Step 5: After the brackets are attached to the GSD-1022UP, use suitable screws to securely attach the brackets to the rack, as shown in Figure 3-3.

Step 6: Proceed with Steps 4 and 5 of Desktop Installation to connect the network cabling and supply power to the GSD-1022UP.

Wall Mounting

Step 1: Please find the wall that can mount the GSD-1022UP.
Step 2: Install two screws on the wall.
Step 3: Hang the GSD-1022UP on the screws from the wall, as shown in Figure 3-4.
Step 4: Proceed with Steps 4 and 5 of Desktop Installation to connect the network cabling and supply power to the GSD-1022UP.

Note Before mounting the device to the wall, please check the loca- tion of the electrical outlet and the length of the Ethernet cable.

Installing the SP Transceiver
The sections describe how to insert an SP transceiver into an SP slot of the GSD-1022UP. The SFP transceivers are hot-pluggable and hot-swappable. You can plug in and out the transceiver to/from any SP port without having to power down the GSD-1022UP as shown in Figure 3-5.

Approved PLANET SP Transceivers
GSD-1022UP supports both single mode and multi-mode SP transceivers. The following list of approved PLANET SP transceivers is correct at the time of publication:
Gigabit SFP Transceiver Modules

Note It is recommended to use PLANET SP on the GSD-1022UP. If you insert an SFP transceiver that is not supported, the GSD- 1022UP will not recognize it.

1. Before you connect the GSD-1022UP to the other network device, we have to make sure both sides of the SP transceivers are with the same media type, for example, 1000BASE-SX to 1000BASE-SX; 1000BASE-LX to 1000BASE-LX.
2. Check whether the fiber-optic cable type matches with the SP transceiver requirement.
3. To connect to 1000BASE-SX SFP transceiver, please use the multi-mode fiber cable with one side being the male duplex LC connector type.
4. To connect to 1000BASE-LX SP transceiver, please use the single-mode fiber cable with one side being the male duplex LC connector type.

Connect the Fiber Cable

1. Insert the duplex LC connector into the SP transceiver.
2. Connect the other end of the cable to a device with SP transceiver installed.
3. Check the LNK/ACT LED of the SP slot on the front of the GSD-1022UP. Ensure that the SP transceiver is operating correctly.

Remove the Transceiver Module

1. Make sure there is no network activity by consulting or checking with the network administrator. Or through the management interface of the switch/ converter (if available) to disable the port in advance.
2. Remove the Fiber-Optic Cable gently.
3. Lift up the lever of the MGB module and turn it to a horizontal position
4. Pull out the module gently through the lever as shown in Figure 3-6.

Product Specifications

Physical Dimensions

The GSD-1022UP dimensions (W × D × H): 220 × 150 × 44mm

Customer Support

Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team.

PLANET online FAQs: https://www.planet.com.tw/en/support/faq
Support team mail address : support@planet.com.tw

Copyright © PLANET Technology Corp. 2023 Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>