AUDIBAX EVENT 18 LED Battery Par Light Instructions

USER’S MANUAL EVENT 18
3x 6W RGBWAUV LED Battery Par Light

DATA SHEET

WELCOME TO AUDIBAX

Thank you very much for choosing Audibax. We hope you enjoy your new product.
It has been developed and designed paying attention to the smallest details, with quality control with European standards supervised by our great team of professional
technicians, who work every day to offer our customers the best quality.
We make sure that every Audibax product is built to last long. All our references are made with long lasting materials and our specialists are dedicated to constantly doing quality controls to guarantee the best result.
Please read carefully this manual in order to use your Audibax product in the best way.
Do not hesitate to visit our website for further information: www.audibax.com

SAFETY INSTRUCTIONS

GENERAL INFORMATION

• It is important to read and follow the instructions carefully.
• Keep all information and instructions in a secure location.
• Always follow the instructions provided.
• Take note of all safety warnings and never remove them from the equipment.
• Use the equipment only as intended and for its intended purpose.
• Ensure that the stands and/or mounts used are sufficiently stable and compatible for fixed installations. Wall mounts should be properly installed and secured, and the equipment should be installed securely to prevent falls.
• When installing the equipment, be sure to observe the relevant safety regulations in your country.
• Do not install or operate the equipment near sources of heat, such as radiators, heat registers, or ovens, and ensure that it is always cooled sufficiently and cannot overheat.
• Do not place sources of ignition, such as burning candles, on the equipment.
• Keep ventilation slits unobstructed.
• For equipment designed for indoor use only should not be used near water, flammable materials, fluids, or gases. Special outdoor equipment should be used in accordance with the manufacturer’s instructions.
• Ensure that no dripping or splashed water can enter the equipment and do not place containers filled with liquids on the equipment.
• Prevent objects from falling into the equipment.
• Use the equipment only with recommended accessories intended by the manufacturer.
• Do not attempt to open or modify the equipment.
• Check all cables after connecting the equipment to prevent accidents or damage due to tripping hazards.
• During transport, take steps to prevent the equipment from falling and causing damage or injury.
• If the equipment is not functioning properly, fluids or objects have gotten inside, or is otherwise damaged, switch it off immediately and unplug it from the power outlet (if applicable). Only authorized, qualified personnel should repair the equipment.
• Clean the equipment with a dry cloth.
• Comply with all applicable disposal laws and separate plastic and paper/cardboard during packaging disposal.
• Keep plastic bags out of the reach of children.

FOR DEVICES DESIGNED TO BE CONNECTED TO THE MAIN POWER SUPPLY:

• ATTENTION: If your equipment has a power cord with a grounding plug, it must be connected to a wall outlet with a ground connection. Never remove the grounding plug from the power cord.
• If your equipment has been exposed to extreme temperature changes, allow it to reach room temperature before turning it on. Otherwise, moisture and condensation may damage the equipment.
• Before plugging in the equipment, make sure that the voltage and frequency of the power outlet match the specifications of the equipment. If the equipment has a voltage selector, only connect it to the power outlet if the values  match. If the power cord or adapter does not fit your outlet, contact an electrician.
• Do not step on the power cord. Make sure it is not pinched at the outlet, adapter, or equipment connection.
• Keep the power cord or adapter within reach and disconnect the equipment from the power supply when not in use or when cleaning it. Always unplug the cord or adapter by pulling the plug or adapter, not the cord. Never touch the  cord or adapter with wet hands.
• Avoid frequently turning the equipment on and off, as this can reduce its useful life.
• IMPORTANT: Only replace fuses with those of the same type and rating. If a fuse repeatedly blows, contact an authorized service center.
• To completely disconnect the equipment from the power mains, unplug the power cord or adapter from the outlet.
• If your device has a Volex power connector, the mating Volex connector must be unlocked before it can be removed. Be careful when laying cables, as the equipment can slide or fall if the power cord is pulled.
• Unplug the power cord or adapter before an extended period of disuse or in case of lightning strike risk.
• Only install the equipment when it is disconnected from the power source.
• To prevent damage and overheating, qualified personnel should regularly clean and service the equipment depending on ambient conditions like dust, nicotine, and fog.
  If the product contains the following symbols, please, read carefully:

CAUTION
Risk of Electric Shock.
Disconnect all power sources before servicing
CAUTION: To reduce the risk of electric shock, do not remove cover (or back). There are no user serviceable parts inside. Maintenance and repairs should be exclusively carried out by qualified service personnel.
The warning triangle with lightning symbol indicates dangerous uninsulated voltage inside the unit, which may cause an electrical shock.
The warning triangle with exclamation mark indicates important operating and maintenance instructions.

IMPORTANT INFORMATION
WARNING! IMPORTANT INFORMATION REGARDING LIGHTING PRODUCTS

1. This product is specifically designed for use in event technology and is not intended to be used as household lighting.
2. It is important to avoid looking directly at the light beam, even for a short period of time.
3. Optical instruments, such as magnifiers, should not be used to look directly at the beam.
4. If you are sensitive to strobe effects, it is possible that they could cause an epileptic seizure. If you have epilepsy, it is important to avoid places where strobe lights are being used.

PACKAGE CONTENT

1 x Event 18
1 x Power cable
1 x Remote control
1 x User’s manual

PRODUCT DESCRIPTION

• Rated voltage: 90V-240VAC, 50/60Hz
• LEDs: 3* 6 W RGBWAUV (6 in 1) LEDs
• Beam angle: 40 degree
• DMX512 Channels: 10 CH
• Dimming: 0-100%
• Built in battery & wireless DMX512, with RF remote control
• Strobe: Independent electronic strobe, 0-20 times / second, the speed can be adjusted
• Battery working time: (+/-) 4 hours Full color,(+/-) 20 hours single color Auto run
• Rapid Recharge Timer: 4-5 hours
• Control Mode: DMX512 control ,Auto Run,Master /Slave,Sound Active
• Product size: 90 x 90 x 100 mm
• Net Weight: 2.8 kgs
• Gross Weight: 3.5 kgs

REMOTE CONTROLLER INSTRUCTIONS

BLACK OUT
Press to turn on the remote control function
Press off existing modes
AUTO
Automatic mode will enable you to run the automatic programs on the product.

1. Press on the remote controller , Display shows “CC00 ”,
2. Press <+> or < – > to either increase or decrease the speed of program
3.  Press to turn off the auto mode

SOUND
Sound-Active mode will enable the product to respond to the music.

1. Press on the remote controller.
2. Press and then press <+> or <- > to increase or decrease the sound sensitivity
3. Press to turn off the sound mode

STROBE

1. Press < STROBE > on the remote controller.
2. Press <+> or < – > to adjust strobe frequency
3. Press to turn off the strobe.

SPEED
Switches the values of the auto programs (CC, CP, dE) between 00 and 99

SENSITIVITY
To adjust sound sensitivity for in Sound-Active mode

1. Press on the remote controller.
2. Press <+> or < – > to either increase or decrease sound sensitivity.

%
% mode will enable you to run the color pulse programs on the product.

1. Press < % > on the remote controller , Display shows “CP00 ”,
2. Press <+> or < – > to either increase or decrease the speed of program
3. Press < BLACK OUT > to turn off the color pulse mode

MANUAL

1. Press on the remote controller.

2. Press , , , , or to choose your wanted colour.
   Press 1 time for 20% brightness;
   Press 2 times for 40% brightness;
   Press 3 times for 60% brightness;
   Press 4 times for 80% brightness;
   Press 5 times for 100% brightness

3. Press <+> or < – > to either increase or decrease the percentage of each colour.