KLEIN TOOLS PJSFM1 Frother Rechargeable Personal Jobsite Fan Instructions

: June 13, 2024
: KLEIN TOOLS

Table of Contents

CONTENTS
GENERAL SPECIFICATIONS
MAINTENANCE
WARRANTY
DISPOSAL / RECYCLE
FEATURE DETAILS (FIG.A)
SYMBOLS ON PRODUCT (FIG.B)
OPERATING INSTRUCTIONS
FCC & IC COMPLIANCE
CUSTOMER SERVICE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)
10D Nail Hole

KLEIN TOOLS PJSFM1 Frother Rechargeable Personal Jobsite Fan

KLEIN TOOLS PJSFM1 Frother Rechargeable Personal Jobsite
Fan

GENERAL SPECIFICATIONS

Cell Type: 18650 Lithium-ion
Capacity: 5200mAh (18.98Wh)
Operating/Storage Altitude: 6562 ft. (2000 m)
Operating Temperature: 14° to 104°F (-10° to 40°C)
Charging Temperature: 32° to 104°F (0° to 40°C) (For optimum charging, ambient temperature should be below 86°F (30°C))
Storage Temperature: -4° to 113°F (-20° to 45°C) (up to 3 months)
Storage Humidity: <75% Relative humidity
Operating/Charging Humidity: <85% non-condensing
Runtime (minimum): High 5 hour, Low 9 Hour
Charging Time: Full charge in 4.5 hours under optimum charging conditions
Shelf Life: Fully charge every 3 months
Life Expectancy: Up to 500 cycles typical (depending on use & care)
Charging Requirements: 5V 2.0A, 10W
Dimensions: 10.6″ x 9″ x 4″ (269 x 228 x 101 mm)
Weight: 2.37 lb (1076 g)
Drop Protection: 3 ft. (.91 m)
Ingress Protection Rating: IP54
Standards: UL 507, CSA C22.2 No. 113-18, FCC: 47CFR Part 15(2018) and ANSI C63.4 (2014), UL 2054, IEC 62133, UN38.3, DOE/CEC, IEC #60335-1, #60335-2-80, RoHS, REACH, NRCan, NOM-003-SCFI-2000 / NMX-J-521/1-ANCE-2012

Specifications subject to change.

WARNINGS

Read, understand, and follow these instructions to ensure safe operation. Failure to observe these warnings can result in risk of fire, electric shock, serious injury and/or property damage.

Use of a power supply, charger, or cable not recommended or sold with this unit may result in a risk of fire or injury to persons.
DO NOT use the product that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
DO NOT subject to vibration, impacts, or drops. The housing may not show signs of damage, but internal components may have been compromised. It is advisable to replace the unit if any such severe events occur.
DO NOT expose to direct sunlight, open flame, heat sources, equipment that produces heat, or extremes in environmental temperature.
DO NOT expose product to rain or snow.
Keep away from high voltage devices.
DO NOT attempt to repair the fan or charging cable. There are no user-serviceable parts.
DO NOT immerse in water or other liquids. Avoid spilling liquids or falling foreign objects into openings on the enclosure.
Risk of fire and burns. DO NOT open, crush, heat above manufacturer’s specified maximum temperature or incinerate.
Water-resistant port cover must be properly sealed to achieve specified water & foreign object ingress protection. Keep seal free of dirt, oil, sand, or other material that interferes with proper sealing. Failure to do so can result in risk of fire or electric shock.
DO NOT open water-resistant cover if wet or in a wet environment. Thoroughly dry the unit and the seal around water resistant cover completely before opening water-resistant cover.
When the fan is in use or charging, make sure there is adequate space to allow ventilation of internally generated heat.
Use safety-rated power supply or wall adapter. Never use power supply or wall adapter that exceeds the specified charging voltage and current.
Route the power supply cable so that it will not to be stepped on or pinched by other objects.
DO NOT attempt to insert other USB connector types into USB-C port.

MAINTENANCE

CLEANING : Be sure device disconnected from all power sources and devices. Use clean, dry, soft, lint-free cloth to wipe down the entire unit. Do not use abrasive cleaners or solvents.

STORAGE : If storing for more than 1 month, charge completely before storage, and recharge approximately every 3 months to avoid full discharge. Store in cool temperatures, mild humidity, and away from direct sunlight (See GENERAL SPECIFICATIONS). Leaving in a vehicle or other confined spaces in extreme hot temperatures can lead to decrease in service life, overheating, or fire. Extreme cold temperatures below the specified storage range can also harm performance and service life. Keep away from corrosive chemicals and gases. After taking out of storage, inspect visually to make sure device and all accessories look satisfactory. Allow unit to return to ambient conditions before recharging or charging other devices.

RECHARGING : Recharge as needed. There are no pre-designated intervals at which to recharge as long as you are using the unit regularly. Avoid discharging completely on a regular basis, as this can impact overall life. Regularly inspect ports and charging cable for any debris, dirt, damage, and corrosion. DO NOT attempt to fix. Replace device and/or cable as needed.

WARRANTY

www.kleintools.com/warranty

DISPOSAL / RECYCLE

Do not place equipment and its accessories in the trash.
Items must be properly disposed of in accordance with local regulations. Please see www.epa.gov/recycle for additional information.

FEATURE DETAILS (FIG.A)

Fan blades
Fan cage
Fan cage arms
Clamp (with rubberized grip)
Handle
Power button
Battery status indicator
Charging port flap
USB-C input
10D Nail Hole
Magnets (x2)

SYMBOLS ON PRODUCT (FIG.B)

Warning or Caution
Risk of Electrical Shock
Read Instructions
Conforms with European Economic Area directives
Conforms with United Kingdom Conformity
Assessment Requirements
WEEE: Electronics disposal
Magnet
IP54 Ingress Protection Rating
NOM (Norma Oficial Mexicana)
Independently tested by Intertek and meets applicable standards
Energy efficiency verified

OPERATING INSTRUCTIONS

Read these instructions carefully before operating and keep for future reference.

CHARGING BATTERY

Use the included USB-A to USB-C charging cable and connect the USB-C end to the jobsite fan USB-C input 9 and then connect the USB-A end to the charging source’s USB-A port.
The battery level indicator bars will illuminate (see TABLE 1 below):
- 4 bars solid (Red, Yellow, 2 Green solid): 100% charge
- Red solid, yellow solid, one green solid: 75% to 99% charge
- Red solid, yellow solid, one green blinking: 50% to 74% charge
- Red solid, yellow blinking: 25% to 49% charge
- Red blinking: 0% to 24% charge
A full charge could take up to 4.5 hours, depending on the charger’s output. Charge completely before using. To maximize battery life, see MAINTENANCE section (other side).
To check the battery level, press and hold the power button for 5 seconds. The battery level will illuminate without changing the speed of the fan

TABLE 1

Not Illuminated

|

Green

|

Yellow

|

Red

|

Blinking

USING THE FAN

Pressing the power button will show battery level, releasing the button will turn on the fan:

Press and release once to turn the fan on HIGH
Press and release a second time to turn the fan on LOW
Press and release a third time to turn the fan OFF

NOTE : When charging the fan, the unit will operate at LOW speed only.

MOUNTING OPTIONS

Clamp – open the clamp by squeezing the handles together.
Open the clamp fully and push as far onto the intended object before releasing the clamp. The rubberized texture inside the clamp provides better grip to materials including conduit.
Magnets – two magnets can be placed onto any ferrous surface.
For best results, mount the fan with the magnets aligned vertically.
Nail hole – place the hole over the nail head and slide into the slot for secure mounting.

TROUBLESHOOTING

PJSFM1 will NOT recharge IF :

The charging cable (USB-A to USB-C) is damaged. Replace with equivalent (USB-A to USB-C) charging cable.
The charging source or device is unable to meet specified charging requirements. Use appropriate charging source or device that meets specified charging requirements.
The connector on the charging source is damaged, replace charging source.