KLEIN TOOLS 93MCLG Self Leveling Mini Cross Line Laser Level Instruction Manual

KLEIN TOOLS 93MCLG Self Leveling Mini Cross Line Laser Level Instruction

Manual

GENERAL SPECIFICATIONS

Klein Tools 93MCLS and 93MCLG are self-leveling laser alignment instruments that can be used to deliver horizontal and vertical cross lines for alignment and layout applications. Their compact size allows for easy storage with convenient storage pouch.

• Operating Altitude: 6562 ft. (2000 m)

• Relative Humidity: <80% non-condensing

• Operating Temp: 20°F to 115°F (-10°C to 45°C)

• Storage Temp: -5°F to 140°F (-20°C to 60°C)

• Lasers: • 93MCLS: 630-642 nm, =<1 mW each beam,
  Class II laser Product

• 93MCLG: 508-530 nm, =<1 mW each beam,
  Class II laser Product

• Accuracy: ±3/16″ (±5 mm) per 33 ft (10 m).

• Battery Type: 2 × 1.5V AA Alkaline

• Dimensions: 3.1″ × 2.9″ × 2.2 ( 79 × 73.7 × 55.9 mm)

• Weight: 7.4 oz. (210 g) without battery

• Calibration: Accurate for one year

• Standards: Conforms to: EN 50689:2021, IEC 60825-1:2014.
  Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed. 3., as described in Laser Notice No. 56, dated May 8, 2019.

• Ingress Protection: IP54 Dust & Water Resistant

Specifications subject to change.

WARNINGS
To ensure safe operation and service of the instrument, follow these instructions. Failure to observe these warnings can result in serious personal injury, fire, or electrical shock. Retain these instructions for future reference.

WARNING: LASER RADIATION. DO NOT STARE INTO BEAM. Class 2 Laser.

• Exposing eyes to laser radiation can result in severe and permanent eye injuries.
• NEVER look directly into the laser beam emitted by this instrument.
• DO NOT use the instrument if it appears to be damaged.
• DO NOT modify the instrument in any way, as to do so could result in emission of hazardous laser radiation than could result in severe eye injuries.
• DO NOT use optical equipment such as lenses, prisms, optical scopes, etc. to transmit, retransmit, or view the laser beam as this could result in severe eye injuries.
• This product should not be used by untrained operators or operators who have not read and fully understood the instructions.
• DO NOT remove warning labels from this instrument as this could result in serious personal injury and increases the risk of exposure to hazardous laser irradiation.
• This instrument is IP54 dust & water resistant. Following any contact with water, thoroughly dry the instrument with a dry, lint-free cloth.
• There are no user serviceable parts in this instrument.

FEATURE DETAILS

SYMBOLS ON INSTRUMENT

FIG 2 SYMBOLS ON INSTRUMENT.JPG

FIG 3 SYMBOLS ON INSTRUMENT.JPG

OPERATING INSTRUCTIONS

VERIFYING ACCURACY OF LASER LINES

HORIZONTAL BEAM LEFT/RIGHT TILT
Position the instrument on the floor x distance from front of the device to the vertical wall as shown. Rotate the instrument on the bracket to the left so that the right side of the beam is projected on the wall directly across from the instrument, mark the vertical location on the wall (a). Rotate the instrument to the right and repeat marking the vertical location of the left side of the beam (b). The maximum distance (delta) between a and b is shown in the table below.

HORIZONTAL BEAM OUT-OF-PLANE TILT

VERTICAL BEAM TILT

BATTERY REPLACEMENT

When the laser lines flash 3 times within 1.5 seconds followed by 30 seconds of solid laser lines, the batteries must be replaced.

CLEANING

Be sure laser level is turned off and wipe with a clean, dry lint free cloth. Do not use abrasive cleaners or solvents.

STORAGE

Remove the batteries when the instrument is not in use for a prolonged period of time. Do not expose to high temperatures or humidity. After a period of storage in extreme conditions exceeding the limits mentioned in the General Specifications section, allow the laser level to return to normal operating conditions before using.

FCC AND IC COMPLIANCE

See this product’s page at www.kleintools.com for FCC compliance information.
Canada ICES-003 (B) / NMB-003 (B)

WARRANTY

www.kleintools.com/warranty

DISPOSAL / RECYCLE

Do not place equipment and its accessories in the trash.
Items must be properly disposed of in accordance with local regulations. Please see www.epa.gov/recycle for additional information.

CUSTOMER SERVICE

KLEIN TOOLS, INC.
450 Bond Street Lincolnshire, IL 60069 1-800-553-4676
customerservice@kleintools.com www.kleintools.com

Read More About This Manual & Download PDF:

References

• Reduce, Reuse, Recycle | US EPA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>