NINGBO XJ-WB62 WiFi Bluetooth LE 5.0 Combo Module Instruction Manual
- June 13, 2024
- Ningbo
Table of Contents
NINGBO XJ-WB62 WiFi Bluetooth LE 5.0 Combo Module Instruction Manual
Summary
Product characteristics
?802.11b/g/n,Wi-Fi+BluetoothLE5.0Combo,support STA,SoftAP&Sniffer
- Open source, autonomous and controllable RISC-V CPU,1~160MHz ,276KB SRAM
- Ultra low power consumption:Sleep power consumption only 0.5uA,Connected standby consumption
- 40uA(DTIM10)
- Ultra fast connection:Cold start fast connect only70ms
- Ultra Long Range:Maximum transmission power21dBm,sensitivity-98dBm
- High security:Support secure startup、Safety debugging、AES128/192/256encryption engine、WPA3、
- MD5、SHA-1/224/256、PKA (RSA/ECC)encryption engine
- support Wi-Fi & BluetoothLE coexistence
Application Scenario
- Smart lighting
- Smart switch
- Smart socket
- Smart appliance
- Monitoring and remote control
Description
XJ-WB62 is Wi-Fi & BluetoothLE combination。Include 2.4GRF、Wi-Fi 802.11b/g/nandBLE b a s e b a n d / MACdesign。The power management unit provides flexible settings to achieve low power consumption mod e and supports multiple security functions.
Functional Block Diagram
1.X J – W B 6 2 Functional Block Diagram
PINDefine
PINInterface diagram
2.TGW206-16
Pin Function
NO| Name| IO Type| Description| Configurable
Functions
---|---|---|---|---
1| CHIP_EN| I/O| Chip enable pin (active high)|
2| GPIO5| I/O| GPIO5| SDIO,SPI, I2C, UART, PWM0, ADC,ACOMP
3| GPIO2| I/O| GPIO2| SDIO, SFLASH, SPI, I2C, UART, PWM2
4| GPIO11| I/O| GPIO11| SPI, I2C, UART, PWM1, ADC,
5| GPIO12| I/O| GPIO12| SPI, I2C, UART, PWM2, ADC, ACOMP
6| GPIO14| I/O| GPIO14| SPI, I2C, UART, PWM4, ADC, ACOMP, DAC
7| GPIO17| I/O| GPIO17| SPI, I2C, UART, PWM2,
8| VCC| P| Power supply. 3.3V is required|
9| GND| P| Ground connections|
10| GPIO0| I/O| GPIO0| SDIO, SFLASH, SPI, I2C, UART, PWM0
11| GPIO8| I/O| GPIO8 (Boot option).| SPI, I2C, UART, PWM3
12| GPIO1| I/O| GPIO1| SDIO, SFLASH, SPI, I2C, UART, PWM1
13| GPIO3| I/O| GPIO3| SDIO, SPI, I2C,PWM3, 用户通讯串口 RXD
14| GPIO4| I/O| GPIO4| SDIO, SPI, I2C, PWM4, ADC, ACOMP,用户通讯串口 TXD
15| RXD| I/O| UART RX| 该串口只能作为烧录及日志输出串口
16| TXD| I/O| UART TX
Property Specifications
WiFi RF
Product Name | X J – W B 6 2 Module |
---|---|
Standard | IEEE 802.11b/g/n |
Frequency Band | 2.4~2.4835GHz ISM Band |
Modulation Type | 802.11b: CCK, DQPSK, DBPSK |
802.11g: 64-QAM,16-QAM, QPSK, BPSK
802.11n: 64-QAM,16-QAM, QPSK, BPSK
Data Transfer Rate| 1,2,5.5,6,11,12,18,22,24,30,36,48,54,65,72.2Mbps
Spread Spectrum| IEEE 802.11b: DSSS (Direct Sequence Spread Spectrum)
IEEE802.11g/n: OFDM (Orthogonal Frequency Division Multiplexing)
RX Sensitivity| 11b-1Mbps: -98dBm
11b-11Mbps: -91dBm
11g-54Mbps: -77dBm
11n HT20-MCS0: -92dBm
11n HT20-MCS7: -73dBm
Maximum Input Level| 11b: 5dBm
MCS0: -4dBm
MCS7: -13dBm
Output Power| 11b: 18.25dBm
11g: 18.89dBm
11n: 18.88dBm
Interface| UART
Power Supply| DC3.3V
Operating Temperature| -30℃ to +85℃
Size:| 24mm×16mm×2.75mm
BLE RF
Parameter | Conditions | Minimum | Typical | Maximum | Unit |
---|---|---|---|---|---|
Frequency range | 2402 | 2480 | MHz | ||
RX sensitivity | 1 Mbps | – | -93 | – | dBm |
Initial carrier frequency offset | -24 | 5 | 24 | KHz | |
Output power | BLE 1M | – | 7.055 | – | dBm |
Electrical parameters
parameters | minimum value | Typical value | Maximum value | unit |
---|---|---|---|---|
VDD | 2.2 | 3.3 | 3.6 | V |
Distribution current | – | 120 | – | mA |
Work current | – | 55 | – | |
Standby current | – | 23 | – |
Reference application & PCB Layout4
Application schematic diagram
3. X J – W B 6 2
PCB Layout
- Maintain clear space at the module antenna
- Keep the module away from strong interference sources
- Increase the capacitance at the power supply, and ensure that the wiring is short and thick
- The module can be attached to the PCB board or welded to the PCB board with 2.0 pins. 4.2.5 The PCB can be connected to an onboard antenna or an IPEX socket to an external antenna (as follows)
- Onboard antenna:R8(0R) / R9(NC)
- PEX Seat external antenna:R8(NC) / R9(0R)
The recommended module layout is as follows
4 .X J – W B 6 2
PCB package
package size
5.X J – W B 6 2
Pad
6.X J – W B 6 2
software package
Reflow soldering curve
Referred to IPC/JEDEC standard.
Peak temperature: <250°C
Reflow soldering curve
Revision History
parameters | minimum value | Typical value | Maximum value | unit |
---|---|---|---|---|
VDD | 2.2 | 3.3 | 3.6 | V |
Distribution current | – | 120 | – | mA |
Work current | – | 55 | – | |
Standby current | – | 23 | – |
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarant ee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environm ent. This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitte
This module is suitable for appliances such as heaters and heaters. When integrated into the main product, the main product will provide a voltage stabilizing circuit and a 3.3V power supply..
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.The end user manual shall include all
required regulatory information/warning as show in this manual Integration
instructions for host product manufacturers according to KDB 996369 D03
OEMManual v01
List of applicable FCC rules
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the
modular transmitter
Specific operational use conditions
This module is stand-alone modular. If the end product will involve the
Multiple simultaneously transmitting condition or different operational
conditions for a stand-alone modular transmitter in a host, host manufacturer
have to consult with module manufacturer for the installationmethod in end
system.
Limited module procedures
Not applicable
Trace antenna designs
Not applicable
RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Antennas
This radio transmitter XJ-WB62 has been approved by Federal Communications
Commission to operate with the antenna types listed below, with the maximum
permissible gain indicated. Antenna types not included in this list that have
a gain greater than the maximum gain indicated for any type listed are
strictly prohibited for use with this device.
version | REVISION | Modified By | Date |
---|---|---|---|
V0.1 | first edition | MJ | 2020.08.09 |
V0.2 | Update series naming | MJ | 2020.10.27 |
V0.3 | Update GPIO function description | MJ | 2022.01.13 |
Label and compliance information
The final end product must be labeled in a visible area with the following”
Contains FCC ID: 2AXSO-XJ-WB62″
Information on test modes and additional testing requirements
Host manufacturer is strongly recommended to confirm compliance with FCC
requirements for the transmitter when the module is installed in the host.
Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with module
installed with all other applicable requirements for the system such as Part
15 B.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>