mitzi HL699101-SBK One Light Wall Sconce Onda Instruction Manual

mitzi HL699101-SBK One Light Wall Sconce Onda

Product Information

• Product Name: Onda HL699101
• Manufacturer: Hudson Valley Lighting
• Compatible Brands: Troy Lighting, Mitzi, Corbett Lighting

Product Usage Instructions

Hardwire Fixture Installation

1. Attach the MOUNTING PLATE (A) unto the junction box using the MOUNTING SCREWS (B). Ensure that the junction box is securely mounted to the building structure.
2. Attach the Ground wire (C) to the ground inside the outlet box or the GROUND SCREW (D) on the MOUNTING PLATE (A). Never connect the ground wire to the hot wire to prevent serious injury or death.
3. Connect the white fixture lead to the neutral wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (E). Secure the connection with electrical tape to avoid short circuits.
4. Connect the black fixture leads to the hot wire in the junction box. Fasten the wires together as done in the previous step. Never reverse hot and neutral wires to prevent serious injury or death.
5. Attach the FIXTURE ASSEMBLY (H) to the MOUNTING PLATE (A) and secure it with the SET SCREWS (E).
6. Place the SHADE (K) onto the FIXTURE ASSEMBLY (H) and secure it using the RING (I).
7. Screw the BULB (J) into the SOCKET of the fixture. Ensure that the bulb does not exceed the recommended wattage of 60 watts (Type A lamp).
8. Restore power to the outlet at the breaker or fuse box.
9. Turn the SWITCH (L) on the FIXTURE ASSEMBLY (H) to activate the light.

Precautions

WARNING/CAUTION

• DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
• TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
• CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
• UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
• PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.

Installation Instructions

HARDWIRE FIXTURE INSTALLATION

1. Attach the MOUNTING PLATE (H) unto the junction box using the MOUNTING SCREWS (J). This fixture is designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
2. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the GROUND SCREW (L) on the MOUNTING PLATE (H). NEVER CONNECT GROUND WIRE TO “HOT” WIRE. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
3. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (K). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT.
4. Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
5. Attach the FIXTURE ASSEMBLY (H) to the MOUNTING PLATE (A) and secure with the SET SCREWS (E).
6. Place the SHADE (K) onto the FIXTURE ASSEMBLY (H) and secure using the RING (I).
7. Screw the BULB (J) up into the SOCKET of the fixture. THIS FIXTURE IS RATED FOR 60 WATT TYPE A LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE.
8. Restore power to the outlet at the breaker or fuse box.
9. Turn the SWITCH (L) on the FIXTURE ASSEMBLY (H).

PLUG IN FIXTURE INSTALLATION

1. Mark holes on the wall for the WALL ANCHORS (F), drill holes on the ceiling and push the WALL ANCHORS (F) into the wall.
2. Attach the MOUNTING PLATE (A) onto the wall, secure the WOOD SCREWS (G) into the WALL ANCHORS (F).
3. Attach the FIXTURE ASSEMBLY (H) to the MOUNTING PLATE (A) and secure with the SET SCREWS (E).
4. Place the SHADE (K) onto the FIXTURE ASSEMBLY (H) and secure using the RING (I).
5. Screw the BULB (J) up into the SOCKET of the fixture. THIS FIXTURE IS RATED FOR 60 WATT TYPE A LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE.
6. Restore power to the outlet at the breaker or fuse box.
7. Plug the CORD (M) into the wall outlet. Turn the SWITCH (L) on the FIXTURE ASSEMBLY (H).

PART(S)/ REPLACEMENT PART NAME /NUMBER

• A,B,C,D,E,F,G/ HARDWARE KIT/ HDW-HL699101
• I/ RING/ RNG-HL699101
• K/ SHADE/ SHD-HL699101

www.hvlgroup.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>