SUNSUN CTM-4800 SuperEco Pond Pump User Manual
- June 4, 2024
- SUNSUN
Table of Contents
SUNSUN CTM-4800 SuperEco Pond Pump
Please read and follow the operating instructions and safety information prior to the initial operation. Technical changes reserved! Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further developments.
The information contained in this document may alter at any time without prior notice. No part of this document may be copied or otherwise duplicated without prior written consent. All rights reserved. WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating manual, nor in the diagrams and illustrations shown. Although WilTec Wildanger Technik GmbH has made every possible effort to ensure that this operating manual is complete, accurate, and up-to-date, errors cannot be ruled out entirely. If you have found an error or wish to suggest an improvement, we look forward to hearing from you.
Send us an e-mail to: service@wiltec.info
or use our contact form: https://www.wiltec.de/contacts/
The most recent version of this manual in several languages can be found in our online shop: https://www.wiltec.de/docsearch
Our postal address is: WilTec Wildanger Technik GmbH Königsbenden 12 52249 Eschweiler Germany
To return your goods for an exchange, repair, or other purposes, please use the following address. Attention! To allow for a trouble-free complaint or return, it is important to contact our customer service team before returning your goods.
- ADDRESS: Retourenabteilung WilTec Wildanger Technik GmbH Königsbenden 28 52249 Eschweiler Germany
- E-mail: service@wiltec.info
- Phone: +49 2403 55592–0
- Fax: (+49 2403 55592–15)
Introduction
Thank you for choosing to purchase this quality product. To minimize the risk of injury, we ask you to always take some basic safety precautions when using this product. Please read this operating manual carefully and make sure that you understand it. Keep these operating instructions in a safe place.
Caution
- In and near standing water, garden ponds, and swimming ponds, the use of this device is only allowed with a fault current protection switch with a triggering nominal current up to 30 mA (according to VDE 0100 Article 702 and 738).
- The device is not suitable for use in swimming pools, paddling pools of any kind, or bodies of water in which people or animals may stay during operation. Operation of the device with people being in the danger area is not permitted. Ask an electrician, if necessary.
- The device is not intended for use by persons (including children) with impaired or limited physical, sensory, and mental abilities or lack of experience and/or real knowledge unless they are supervised by a person responsible for their safety or follow the instructions made by this person on how to correctly use the device.
- Children should be supervised to ensure that they do not play with the device.
Attention
- Perform a visual inspection of the device before every use. Do not use the device if the safety appliances are damaged or worn out. Never override safety regulations.
- Only use the device accordingly to the intended purpose stated in this manual.
- You are responsible for the safety of the working zone.
- If the cable or the plug is damaged due to external influences, the cable must not be repaired. It must be replaced with a new one. This work may only be carried out by a qualified electrician.
- The voltage of 230 V AC indicated on the nameplate of the device must match the existing mains voltage.
- Never lift, carry, or fix the device by using the power cable.
- Make sure that the electrical plug connection is protected from flood and moisture.
- Always unplug the appliance before working on it.
- Avoid exposing the device to direct water jets or rain.
- The user is responsible for complying with local safety and mounting regulations. Ask an electrician, if necessary.
- The user must take appropriate measures (e.g., installation of an alarm system, a reserve pump, etc.) to prevent damage caused by the flooding in case of device malfunctioning.
- In case of device failure, repairs can only be carried out by an electrician.
- The device must never run dry or be operated with its suction line fully closed.
- Do not use this device to operate swimming pools.
- This device must not be integrated into any kind of domestic water circuit meant for potable water.
Warning: Read all safety precautions and instructions. Failure to obey the safety precautions and instructions might cause an electric shock, a fire, and/or severe injuries. Keep all safety precautions and instructions for future use.
Resistance
The maximum temperature of the pumped liquid should not exceed +35 ℃ in continuous operation. The transport of aggressive fluids (acids, bases, etc.) as well as of abrasive substances (e.g., sand) must be avoided.
Electrical connection
- The electrical connection is made to an earthed socket 230 V ~ 50 Hz. Fuse min. 6 A.
- The motor is protected from overcharge and blockage with the help of built-in thermal motor protection. When overheated, the pump motor is automatically switched off by the thermal protection; after cooling down, the pump automatically re-starts.
Mains connection
The pond pump that you have purchased is already equipped with a protection plug. The pump is meant to be connected to a 220/230 V~50 Hz safety socket. Make sure that the socket is sufficiently protected (min. 6 A) and fully functional. Plug in the plug, the pump is operational.
Installation
- Make sure that the existing mains voltage and frequency match the specifications on the name plate.
- Do not place the pump directly into the pond mud. Place it on a stone to avoid that mud be sucked in.
- Check the pump head (maximum depth). The corresponding value is given on the nameplate, too.
- The pump is installed the following way: either in a stationary position with a fixed pipeline or in a stationary position with a flexible pipeline.
- Place the cable in a secure manner so that it cannot be damaged.
- Connect the pump to the power supply.
- The pump works until it is disconnected again.
Commissioning
After thoroughly reading the instructions for installation and use, you can operate the pump; obey the following hints:
- Check if the pressure line is properly attached.
- Check if the electric source has 230 V~50 Hz.
- Check if the socket is in a good condition.
- Make sure that neither humidity nor water may get into contact with the mains connection.
- Place the pump beneath the surface of the water.
- Avoid any running dry of the pump.
- Never operate the pump without a filter basket; a filter basket protects the pump against any coarse dirt that would obstruct the pump.
- Do not place the pump directly into the pond mud.
Maintenance hints
- The pond motor pump is a practice-proven quality product subjected to rigorous final inspections.
- However, for long working life and continuous operation, we recommend regular checking and proper care.
- To ensure proper operation of the pump, it is necessary that you perform regular cleaning. We recommend that the pump be cleaned on a weekly basis.
- Clean the pump with a soft brush and under running water. Remove all residues accumulated on the pump shaft.
Wintering
- Take the pump out of the water and disconnect it from the power supply.
- Clean the pump as described in the instructions.
- Check the pump for damage such as cracks in the housing.
- Store the pump under frost-free condition and, if possible, in a container with water.
Exploded view, parts list, and structure
№| Name| №| Name
1| Nut| 7| Rotor unit
2| O-ring 1| 8| O-ring 3
3| Outlet| 9| Ceramic bearing
4| Outlet adaptor| 10| Ceramic bearing
5| O-ring 2| 11| Motor housing
6| Pump housing| |
Technical specifications
Item num- ber| Model| Power consumption
(W)
| Max. flow rate (ℓ⁄h)| Lifting height (m)
---|---|---|---|---
50378| CTM- 4800| 30| 4500| 4
50379| CTM- 5800| 40| 5200| 4.8
50380| CTM- 5000| 30| 5000| 3.2
50381| CTM- 6000| 40| 6000| 4.2
50382| CTM- 7000| 50| 7000| 4.6
50383| CTM- 8000| 70| 8000| 5.6
51024| CTM- 2800| 10| 3000| 2
51025| CTM- 3800| 20| 3600| 2.8
51026| CTM- 10000| 80| 10,000| 6
51027| CTM- 12000| 70| 12,000| 5.6
51028| CTM- 14000| 120| 14,000| 7
51029| CTM- 16000| 140| 16,000| 7.5
- Power supply: 230 V~50 Hz
- Length of cable (m): 10
- Particle size (㎜): 6
- Hose connection (㎜): 25 / 33 / 38 (1″–1½″)
Regulations for waste disposal
The Waste Electrical and Electronic Equipment Directive (WEEE Directive,
2012/19/EU) of the EU was implemented in the German law related to electrical
and electronic equipment and appliances.
All WilTec electric devices that fall under the WEEE directive are labeled
with the symbol of a crossed-out wheeled rubbish bin. This symbol indicates
that this electric device must not be disposed of with domestic waste.
WilTec Technik GmbH is registered with the German registration authority EAR
(Stiftung Elektro-Altgeräte Register) under the WEEE-registration number
DE45283704.
Disposal of used electrical and electronic devices (intended for use in the
countries of the European Union and other European countries with a separate
waste collection system for these devices).
The symbol on the packaging or the product itself indicates that this product
must not be treated as normal domestic waste but must be disposed of at a
recycling collection station for electrical and electronic waste. By disposing
of this product correctly, you contribute to the protection of the environment
and the health of your fellow people. Inappropriate disposal threatens the
environment and health.
Material recycling helps to reduce the consumption of raw materials. Additional information about the recycling of this product can be provided by your local commune, the municipal waste disposal facilities, or the store where you purchased the product.
Address: WilTec Wildanger Technik GmbH Königsbenden 12 / 28 52249 Eschweiler Germany
Important Note: Reproduction and any commercial use (of parts) of this operating manual, requires written permission of WilTec Wildanger Technik GmbH.
References
- Aoyue.de
- Teichtip.de
- WilTec - Ihr Online Shop für Haus, Garten, Werkstatt, Freizeit
- Unternehmen: WilTec Wildanger Technik GmbH