Honeywell ES800 Portable Evaporative Air Cooler User Manual
- October 30, 2023
- Honeywell
Table of Contents
Honeywell ES800 Portable Evaporative Air Cooler User Manual
PARTS DESCRIPTION
- Remote Control
- Louvers
- Water Level Indicator with Light
- Detachable Water Tank
- Remote Control Receptor
- Control Panel
- Handle
- Castors
- Rear Grill
- Power Cord Inlet
- Power Adapter & Cord
WARNING — READ AND SAVE THE AIR COOLER SAFETY & MAINTENANCE GUIDE AND USER MANUAL BEFORE USING THIS PRODUCT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY DAMAGE AND/ OR IMPAIR ITS OPERATION AND VOID THE WARRANTY. IN CASE THERE IS ANY INCONSISTENCY OR CONFLICT BETWEEN THE ENGLISH VERSION AND ANY OTHER LANGUAGE VERSION OF THE CONTENT OF THIS MATERIAL, THE ENGLISH VERSION SHALL PREVAIL
USE & OPERATION
CONTROL PANEL
-
Model without Ionizer
-
Model with Ionizer*^
Icons on Display Screen
Power ON/OFF
Cool
Speed
Timer
Ionizer*^
Swing
QuietSleep
TurboBlast
Low Water Alarm
*Applicable for models with this feature only.
^ Ionizer reduces particles in the air. This is not an air purifier
FUNCTION BUTTONS
POWER
Connect the power adapter to the cooler and to the electrical outlet. Press
the button to turn the unit on. The cooler will start automatically at low
speed. To turn the unit off, press the button again.
*COOL or COOL/IONIZER^ /**
Press the COOL/ION / button until is illuminated on the display screen. This
activates evaporative cooling. The water pump will operate and you will feel
the cooler air after the Honeycomb Cooling Media is completely wet.
WARNING: Please ensure sufficient water is in the water tank otherwise you may hear a Low Water Alarm and the cooler will start in a Fan only mode without evaporative cooling.
An Ionizer helps to reduce particles in the air, thus promoting cleaner air quality. For models with the Ionizer feature, pressing the / button again will activate the Ionizer and you will see illuminated on the display. When is not illuminated, the unit will function in a Fan only mode without evaporative cooling.
Press the / button until both and lights are illuminated together on the display screen. Both Cool and Ionizer can be activated imultaneously.
To turn off Cool and Ionizer, press the button until both and icons are switched off from the display screen, or press the button to turn off the unit.
SPEED
Press the button repeatedly to change the fan speed between – – – .
When AUTO is selected, the wind speed will gradually decrease and increase between the TurboBlast and QuietSleep fan speeds.
QUIETSLEEP/ TURBOBLAST
Press the button to select either QuietSleep or TurboBlast modes. QuietSleep
mode minimizes wind sp
eed for lower airflow. TurboBlast mode blasts wind at high speed for stronger
airflow.
Note: In QuietSleep mode, all the display lights of the unit will be
switched off. The lights can be switched on by pressing any button.
TIMER
Press the button until the desired time duration setting is selected. When the
set time has passed, the unit will automatically turn off (unit remains in
Standby mode until power cord is unplugged from electrical socket). The TIMER
function allows you to program the unit for up to 7.5 hours of use
REMOTE CONTROL
POWER: ON / OFF
FAN SPEED: Low / Medium / High / Auto
SWING: Controls the motion of the louvers
COOL / IONIZER : Cooling or Ionizer*^ function ON / OFF
TIMER: Controls the Timer function for automatic off
QuietSleep / TurboBlast : QuietSleep / TurboBlast mode
*Applicable for models with this feature only.
^ Ionizer reduces particles in the air. This is not an air purifier.
NOTE:
- The remote control requires a CR2025 (1 x 3V) coin type or equivalent battery for replacement. Open the battery compartment at the back of the remote control and insert the battery inside. Care must be taken to insert the batteries according to the correct polarity (+ / –) markings shown inside the battery compartment.
- Always point the remote control signal transmitter towards the unit when operating. Make sure that the signal path is not obstructed.
- Remove the batteries if the unit is not going to be used for an extended period of time.
- Do not drop the remote control.
- Do not mix different types of batteries such as alkaline, carbon-zinc, or rechargeable batteries.
- Do not mix old and new batteries.
- Do not recharge the battery.
- Exhausted batteries are to be removed from the product and safely disposed of as per local regulations.
- Do not dispose of batteries in fire. Batteries may explode or leak.
- This product contains a lithium button/coin cell battery. If a new or used lithium button/ coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
- The batteries shall be disposed of properly, including keeping them away from children.
- Even used batteries may cause injury.
- WARNING: Chemical Burn Hazard. Keep batteries away from children.
COOLER LOCATION
Make sure to position the air cooler correctly before you set up and start using the product. Please refer to the COOLER LOCATION section of the separate Safety & Maintenance Guide.
FILLING WITH WATER & ICE
CAUTION:
Remove the power adapter and cord from the unit and the electrical outlet
before emptying or refilling the water tank. Wait for 2 minutes before
removing the Water Tank to allow any excess water in the Honeycomb Cooling
Media to drip into the tank before removing it.
Note: After removing the tank, water from the Honeycomb may continue to drip and collect in the tank compartment. Simply wipe dry with a clean, dry cloth.
Slide out the Water Tank. Refill the tank when water level is low. Do not fill
water above the “Max.” water level mark to avoid water droplets collecting on
the louvers. Check the water level in the tank before running the COOL
function. The Low Water Alarm will sound when water is low. Running the unit
in COOL mode with inadequate water may cause pump failure.
If ice is available, you may add ice in the top ice compartment to enhance the cooling performance.
Note: The water capacity refers to the total volume of water that can be
contained within the air cooler water tank and water distribution system. The
water capacity in the tank at the “Max.” indicator level may be lower than the
actual water capacity of the air cooler.
WARNING: Do not fill water tank with dirty water or salt water. This can damage the unit and Honeycomb media
**WATER FILTER***
Some models are equipped with a water filter in the tank, which helps to
filter dust, hair and other particles from entering the water tank. Simply
pour water over the filter when refilling the tank.
To clean the water filter, simply push the bottom of the filter cup upwards to release from the filter frame. Remove dust and hair from the filter sponge and rinse under clean water. When clean, replace the sponge and secure the filter cup back into the frame.
*Applicable for models with water filter feature only.
AUTO-OFF SAFETY SYSTEM
This unit is equipped with an Auto-Off Safety System. When the water tank is
detached from the unit or if the tank is incorrectly positioned, the air
cooler will turn off automatically. To restart the cooler, the tank must be
attached to the unit correctly
**LOW WATER ALARM***
The unit is equipped with a low water sensor. In Cooling Mode, when water in the tank is below the minimum level, you will hear a beeping sound and the indicator light will flash continuously. The unit will automatically pause evaporative cooling.
Refill the water tank to deactivate the alarm in cooling mode. First switch OFF the unit and unplug from the power outlet. Fill the water tank with water above the minimum water level mark. Plug in and switch ON again.
To deactivate the alarm and continue using the unit as a fan (without evaporative cooling), switch the unit OFF and then ON again. The Low Water Alarm will not activate in Fan only mode. The Low Water Alarm will sound again if the COOL function is activated while the water tank is still empty
WATER LEVEL INDICATOR LIGHT
When the unit turns on, the water level indicator located at the front of the water tank will light up to produce an elegant glow. This can be convenient as a night light during the night. This light will remain on for as long as the air cooler is turned on.
CLEANING & DRAINING THE WATER TANK
If the cooler will not be used for a long period of time, please refer to the STORAGE & MAINTENANCE GUIDELINES located in the separate Safety & Maintenance Guide.
WARNING:
Before cleaning the unit, switch the unit OFF and disconnect the power adapter
from the unit and electrical socket
- Slide out and empty the water tank.
- Rinse the water tank with clean water.
- Carefully remove the Water Tank Filter* (if your unit has this) from the tank. Remove dust and hair from filter and then rinse with water until clean. Dry and replace the filter back into the water tank.
- Use a damp cloth to remove dirt and dust from the surface of the unit. Never use corrosive elements or chemicals to clean this product.
- When the product is not in use, store the unit in a dry place out of direct sunlight.
*CLEANING THE CARBON DUST FILTER AND HONEYCOMB COOLING MEDIA**
WARNING:
Before cleaning the unit, switch the unit OFF and disconnect the power adapter
from the unit and electrical socket.
- The appliance is supplied with a Carbon Dust Filter* and Honeycomb Cooling Media.
- The Carbon Dust Filter* and Honeycomb Cooling Media are located inside the Rear Grill. See Figure 1 for instructions on how to remove them from the unit for cleaning and maintenance.
- Do not run the unit in COOL mode with stale water in the tank. You must empty the water tank and refill with fresh water, especially if the tank has not been cleaned in a long time.
- The cleaning frequency for the Honeycomb media depends on local air and water conditions. In areas where the mineral content of water is high, mineral deposits may build up on the Honeycomb Cooling Media and restrict air flow. Draining the water tank and refilling with fresh water at least once a week will help reduce mineral deposits. If mineral deposits remain on the Honeycomb Cooling Media, the media should be removed and washed under fresh water. The media should be cleaned every two months or sooner, depending on your needs.
- For best results allow the Honeycomb Cooling Media to dry after each use by turning off the cool function 15 minutes before turning the unit off.
*Removing the Carbon Dust Filter/ Honeycomb Cooling Media:**
- Carefully remove the rear grill from the unit.
- Remove the two band holders to release the carbon dust filter*.
- Rinse the filter with clean water and let it dry before re-installing to the rear grill.
- Pull out the Honeycomb Cooling Media. Slide down and remove the Honeycomb Frame.
- Replace or clean media with water and a damp cloth as needed.
WARNING: DO NOT operate the Air Cooler when the Rear Grill is removed from the Air Cooler, or if there is a loose-fitting Rear Grill. Doing so can cause serious injury or dangerous electrical shock.
Applicable for models with Carbon Dust Filter only.
Scane by Qr code
www.honeywellaircomfort.com
E-mail:
info@honeywellaircomfort.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>