mitzi H711506 Mimi Aged Brass 6 Light Flush Mount Instruction Manual

mitzi H711506 Mimi Aged Brass 6 Light Flush Mount

Product Information

The MIMI H711506 is a fixture from the Mitzi lighting collection by Hudson Valley Lighting Group. It is designed for installation in residential or commercial buildings. The fixture is intended to be mounted on a standard round or octagon junction box.

Product Usage Instructions

1. Start by attaching the MOUNTING PLATE (A) to the junction box using the MOUNTING SCREWS (B). Ensure that the junction box is securely mounted to the building’s structure.
2. Connect the Ground wire (Green) to the ground inside the outlet box or to the GROUND SCREW (C) on the MOUNTING PLATE (A). Never connect the ground wire to the hot wire to avoid serious injury or death.
3. Connect the white fixture lead to the neutral wire (Generally white) in the outlet box. Use an approved fastener (WIRE NUT) (D) to secure the wires together. Wrap the connection with electrical tape starting 1 inch below the fastener to seal it and prevent short circuits.
4. Connect the black fixture leads to the hot wire (Generally black) in the junction box. Secure the joined wires as done in the previous step. Never reverse hot and neutral wires to avoid serious injury or death.
5. Attach the FIXTURE ASSEMBLY (F) to the MOUNTING PLATE (A) and secure it with the BOLT NUTS (E).
6. Screw the recommended BULB (G), which is an 8-watt type G16.5 lamp, into the SOCKET of the fixture. Do not exceed the recommended wattage to prevent damage.
7. Hang the GLASS (H) on the FIXTURE ASSEMBLY (F) of the fixture.
8. Finally, restore power to the outlet at the breaker or fuse box.

If any replacement parts are needed, you can find them at www.hvlgroup.com using the following part numbers: HDW-H711506 for the HARDWARE KIT and GLS-H711506 for the GLASS.

WARNING/CAUTION

• DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
• TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
• CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
• UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
• PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.

FIXTURE INSTALLATION

1. Attach the MOUNTING PLATE (A) unto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
2. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
3. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
4. Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires same as previous step.
5. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
6. Attach the FIXTURE ASSEMBLY (F) to the MOUNTING PLATE (A) and secure with the BOLT NUTS (E).
7. Screw the BULB (G) into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 8 WATT TYPE G16.5 LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!
8. Hang the GLASS (H) on the FIXTURE ASSEMBLY (F) of the fixture.
9. Restore power to the outlet at the breaker or fuse box.

• www.hvlgroup.com

Documents / Resources

| mitzi H711506 Mimi Aged Brass 6 Light Flush Mount [pdf] Instruction Manual
H711506, H711506 Mimi Aged Brass 6 Light Flush Mount, Mimi Aged Brass 6 Light Flush Mount, Aged Brass 6 Light Flush Mount, Brass 6 Light Flush Mount, Flush Mount, Mount
---|---

References

• Hudson Valley Lighting Group

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>