mitzi H668701S Alaina Pendant Instruction Manual

: June 13, 2024
: mitzi

Table of Contents

mitzi H668701S Alaina Pendant
Product Information
Product Usage Instructions
FIXTURE INSTALLATION
Documents / Resources

mitzi H668701S Alaina Pendant

Product Information

The product is a lighting fixture manufactured by Hudson Valley Lighting. It is part of the Alaina series, model number H668701S. The fixture is designed to be mounted on a standard round or octagon junction box. The maximum recommended wattage for the bulb is 60 watts (Type G25 lamp).

Product Usage Instructions

Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). Ensure that the junction box is securely mounted to the building structure.
Open the end link on the CHAIN (I) and attach it to the loop on the FIXTURE ASSEMBLY (J). Hang the FIXTURE ASSEMBLY (J) on the CHAIN (I) at the desired height and remove any excess CHAIN (I).
Feed the wire through the CHAIN (I), SCREW COLLAR (G), CANOPY (H), SCREW COLLAR LOOP (F), NIPPLE (E), and MOUNTING PLATE (A). Screw the NIPPLE (E) onto the MOUNTING PLATE (A).
Open the top link on the CHAIN (I) and hang the FIXTURE ASSEMBLY (J) to the SCREW COLLAR LOOP (F).
Cut off any excess wire and strip the insulation off the end of the leads.
Attach the Ground wire (Green) to the ground inside the junction box or to the GROUND SCREW (C) on the MOUNTING PLATE (A). Never connect the ground wire to the hot wire to avoid serious injury or death.
Connect the fixture leads to the neutral (Generally white) wire in the outlet box using an approved fastener (WIRE NUT) (D). Wrap the connection tightly with electrical tape to seal the end of the fastener. Ensure there are no exposed wires or strands that could cause a short circuit.
Connect the smooth fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires securely. Never reverse hot and neutral wires to avoid serious injury or death.
Push the wires back into the junction box. Lift up the CANOPY (H) up to the ceiling and secure it with the SCREW COLLAR (G).
Place the METAL RING (J) on the GLASS (K), then lift the GLASS (K) up to the FIXTURE ASSEMBLY (J) and secure it with the SILICONE WASHER (L) and SOCKET RING (M).
Screw the BULB (N) into the SOCKET of the fixture. Ensure that the wattage of the bulb does not exceed 60 watts.
Restore power to the outlet at the breaker or fuse box.

WARNING/CAUTION

DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.

FIXTURE INSTALLATION

Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
Open the end link on the CHAIN (I) and attach to the loop on the FIXTURE ASSEMBLY (J). Hang the FIXTURE ASSEMBLY (J) on the CHAIN (I) at your desired height, and remove excess CHAIN (I).
Feed the wire through the CHAIN (I) , SCREW COLLAR (G), CANOPY (H), SCREW COLLAR LOOP (F), NIPPLE (E), and MOUNTING PLATE (A), and screw the NIPPLE (E) onto the MOUNTING PLATE (A).
Open the top link on the CHAIN (I), and Hang the FIXTURE ASSEMBLY (J) to the SCREW COLLAR LOOP (F).
Cut off excess wire, and strip the insulation off the end of the leads.
Attach the Ground wire (Green) to the ground inside the junction box (Generally green or bar copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIRE FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH
Connect the fixture lead the ridge(s) to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT
Connect the smooth fixture leads with to the hot (Generally black) wire in the junction box. Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH
Push the wires back into the junction box. Lift up the CANOPY (H) up to the ceiling, and secure with the SCREW COLLAR (G).
Plate the METAL RING (J) on the GLASS (K), then lift the GLASS (K) up to the FIXTURE ASSEMBLY (J) and secure with the SILICONE WASHER (L) and SOCKET RING (M).
Screw the BULB (N) into the SOCKET of the fixture. THIS FIXTURE IS RATED FOR 60 WATT TYPE G25 LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE
Restore power to the outlet at the breaker or fuse box.

PART(S)	REPLACEMENT PART NAME	NUMBER
A,B,C,D,E,F,G	HARDWARE KIT	HDW-H668701S
H	CANOPY	CPY-H668701S
I	CHAIN	CHN-H668701S
K	GLASS	GLS-H668601
L	SILICONE WASHER	WAS-H668701S
J	SOCKET RING	RNG-H668701S
N	BLB-60W-G25	BLB-H668601