RENISHAW RSP3-1 REVO 3-D Scanning Probes Installation Guide
- June 4, 2024
- RENISHAW
Table of Contents
RENISHAW RSP3-1 REVO 3-D Scanning Probes
INTRODUCTION
The RSP3 range of probes gives REVO-2 the ability to carry cranked stylus
arrangements while maintaining optimum metrology performance. The probes can
be used for both 3-D scanning (X, Y, Z) and touch-trigger applications. They
enable accurate scanning measurement with effective stylus lengths ranging
from 20 mm to 394 mm. The RSP3 range is used for 3-axis scanning with fixed
REVO-2 head angles during measurement. Each probe is designed to provide
optimized accuracy and contact force over a specified stylus range.
Consequently, the RSH3 stylus holders are intended for use only with their
respective RSP3 probes.
Key benefits
Workpiece access
REVO’s infinite positioning and crank stylus carrying capabilities provide
better part access. Each RSP3 probe has been optimised for maximun performance
over their specific stylus range and crank carrying capabilities.
High accuracy 3-D scanning
RSP3 probes can be used with both straight and cranked styli for high accuracy
3-D scanning.
Part of the REVO 5-axis multisensor system
RSP3 probes are automatically interchangeable with all other probes available
for REVO-2, including surface finish analysis and non-contact inspection
probes. As a result, the system provides the optimum tool to measure multiple
features all on one CMM platform.
Specification
Probe attributes| Scanning with 3-axis measurement (X, Y, Z) and 3-axis
touch-trigger
---|---
Measurement range| ±0.5 mm deflection in all directions in all
orientations
Overtravel range
| X, Y| 2 mm
+Z| 1.7 mm
-Z| 1.2 mm
Resolution| Capable of <0.1 μm
Spring rate
| Nominally 0.6 N/mm – when using shortest specified stylus Nominally 0.2 N/mm – when using longest specified stylus
Weight
| ****
RSP3-1
| 86 g (3.03 oz) (excluding stylus holder and
stylus)
RSP3-2
| 90 g (3.17 oz) (excluding stylus holder and
stylus)
RSP3-3
| 94 g (3.32 oz) (excluding stylus holder and
stylus)
RSP3-4
| 101 g (3.56 oz) (excluding stylus holder and
stylus)
Effective stylus length range
Always observe the specified stylus range for the scanning module being used.
Stylus holders incorporate M3 thread.
| ****
RSP3-1 + RSH3-1
| EWL 20 mm – 50 mm (0.79 in – 1.97 in)
using 20 mm – 50 mm stylus
RSP3-2 + RSH3-2
| EWL 44 mm – 99 mm (1.73 in – 3.90 in)
using 20 mm – 75 mm stylus
RSP3-3 + RSH3-3
| EWL 114 mm – 194 mm (4.49 in – 7.64 in)
using 20 mm – 100 mm stylus
RSP3-4 + RSH3-4
| EWL 214 mm – 394 mm (7.64 in – 15.51 in)
using 20 mm – 200 mm stylus
Mounting| Magnetised kinematic coupling
Crash protection
| ±X, ±Y, Z| Via break out of probe or stylus holder
+Z| Via integral bump-stop design
Change rack options
| ****
RCP TC-2
| Thermally controlled change port used for RSP3 probe changing (only).
This port mounts to the MRS or MRS2.
FCR25 with FCR25 front spacer kit
| Triple port unit which mounts on MRS. Used for changing RSH3-1/2/3/4 stylus holders.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>