connects2 CAM-VW12 Dual Lens Brake Light Camera User Manual
- June 6, 2024
- Connects2
Table of Contents
User Manual
CAM-VW12
V1.02-21
Volkswagen Crafter
2006 – 2016
Dual Lens Brake Light Camera
PRODUCT FEATURES:
| Reversing Camera| Driving Camera
---|---|---
• Resolution:
• Total Pixels:
• Lens size:
• Image Sensor:
• Night Vision Distance:
• Waterproof Rating:
• Viewing Angle:
• Lens Adjust:
• Video Output:
• Power Rating:| 580 TV Lines
648 x 488 pixels
1.8mm
Colour 1/3” CMOS
35ft
IP68
Vertical: 80° Horizontal: 145° Diagonal: 175°
20° (Vertical movement only)
1.0 Vp-p/75 Ohm
12V| 580 TV Lines
648 x 488 pixels
3.6mm
Colour 1/3” CMOS
IP68
Vertical: 55°
Horizontal: 80° Diagonal:
110°
30° (Vertical movement only)
1.0 Vp-p/75 Ohm
12V
DISCLAIMER
The information provided in this document is subject to change without notice
due to manufacturer changes and/or improvements to the product/s. This
instruction manual is based on documented data and research. The manufacturer
of this product cannot be held responsible for any changes made to the vehicle
by the manufacturer or damages that may occur through the installation of this
product in
accordance with the steps outlined herein.
PRODUCT INFORMATION
Connects2Vision
CAM-VW12
The CAM-VW12 is a dual-lens reverse/driving camera solution for vehicles with
solid rear doors/bulkheads. With the addition of this dual camera, the driver
can view the rear of the vehicle via a live stream, and can additionally
reverse in comfort with the aid of a reverse camera feed.
This product includes the following:
- 1x Dual Lens Reverse/Driving Camera
- 1x 10m 7-pin Extension Cable
- 1x 4-pin to 7-pin Cable Splitter
WIRING DIAGRAM
TECHNICAL SUPPORT
Connects2 want to provide a fast and suitable resolution should you encounter any technical issues. With this in mind, when contacting Connects2, try to provide as much information as possible. This will speed up the process and help us to help you.
Please use our dedicated online technical support centre: support.connects2.com/tickets/technical/
PRIOR TO INSTALLATION
Read the manual prior to installation. Technical knowledge is necessary for
installation. Please ensure you use the correct tools to avoid damage to the
vehicle or product.
Connects2 can not be held responsible for the installation of this
product.
INSTALLATION
- Begin to remove the pre-existing rear brake light. Once removed, disconnect all the wiring/light elements from the plastic housing.
- With the appropriate monitor and place in mind, begin to thread the 10-metre Extension Cable from the opening of the brake light, through the vehicle, all the way to the dashboard.
- Connect the Dual Lens Camera 7-pin connector to the corresponding 7-pin connector on the Extension Cable. Connect the Black (Ground) & Red (Switched +12V) flying wires to their relevant source.
- Attach the Cable Splitter to the opposite end of the Extension Cable.
- Attach the Yellow 4-pin connector from the Cable Splitter to a Reverse Camera Input source. Then connect the Black 4-pin connector to a relevant Video Input source.
- To test the camera connection, turn on the ignition. The rear camera feed should now be visible on the screen. Put the vehicle into reverse and the reverse camera feed will automatically populate on the screen.
If the camera feed is unresponsive, please uninstall the wiring and reinstall it carefully in accordance with the above steps.
For further help and support, please contact us directly at
support.connects2.com/tickets/technical
and fill out a support ticket with the full details of your issue.
NOTES __
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>