motogadget mo.hub LIN Motoscope Tiny All Models Instruction Manual

Instruction Manual
mo.hub

mo.hub LIN Motoscope Tiny All Models

Thank you very much for purchasing a high quality motogadget product – Made in Germany.
Please read the following information and recommendations thoroughly and follow these instructions during installation and use of the instrument. No liability shall be assumed by motogadget for damage or defects resulting from negligence or failure to follow the operating and

contact:
motogadget GmbH
Wollenberger Str. 4 i/j
D – 13053 Berlin
Tel. +49 (0)30-6900410-0
www.motogadget.de
info@motogadget.de
Copyright © 2009-2023 by motogadget GmbH, Berlin motogadget and mo.hub are registered trademarks of motogadget GmbH, Berlin, Germany.

Review of Delivery

All products from motogadget are thoroughly checked to ensure they are completely fault-free when dispatched. Please check the received goods immediately for possible transport damage. If you fi nd any damage or other defi ciencies, please contact us immediately.
In this regard, we refer to our General T erms of Business and Delivery, which are published at www.motogadget.com. Should a return of the received delivery be agreed, please note that we only take back goods in their original packaging. The mo.unit and its accessories must be returned within the legal period of time and without any traces of use. We shall not assume any liability for returns which are insuffi ciently insured or packed.

Exclusion of Liability

THE DEVICE AND ITS ACCESSORIES MUST BE INSTALLED BY A CERTIFIED MOTORCYCLE TECHNICAN AND IN AN AUTHORIZED SERVICE CENTER. REVERSE POLARITY OR VOLTAGE ABOVE 25V MAY RESULT IN DAMAGE TO THE MO.HUB. THE DEVICE THEN HAS TO BE REPLACED AND ALL CLAIMS OF WARRANTY ARE DELETED.
MOTOGADGET ACCEPTS NO LIABILITY FOR DIRECT OR INDIRECT DAMAGE OR SUBSEQUENT DAMAGE OF ANY KIND RESULTING FROM THE USE, INSTALLATION OR CONNECTION OF THE DEVICE OR OTHER DELIVERED EQUIPMENT. THIS EXCLUSION OF LIABILITY PARTICULARLY INCLUDES DAMAGE TO PERSONS, MATERIAL LOSSES AND FINANCIAL DAMAGES. THE USE IN AREAS OF PUBLIC TRAFFIC ENSUES AT THE USER’S OWN RISK.
DEVICE HOUSINGS AND ALL OTHER DELIVERED PARTS MUST NOT BE OPENED OR DISMANTLED. IN CASE OF NON-COMPLIANCE, ALL WARRANTY CLAIMS BECOMES INVALID. THE USE OF THE DELIVERED DEVICE AND ITS ACCESSORIES FOR RACING OR OTHER COMPETITIONS AS WELL AS FOR ANY USE NOT CORRESPONDING TO THE RECOMMENDED APPLICATION ALL WARRANTY CLAIMS SHALL BE INVALID.

Safety Instructions

• THE VEHICLE BATTERY MUST BE COMPLETELY DISCONNECTED PRIOR TO ANY WORK ON THE VEHICLE’S ELECTRICAL SYSTEM. FIRST, DISCONNECT THE NEGA- TIVE TERMINAL AND THEN THE POSITIVE TERMINAL. FOR RECONNECTION PROCEED IN THE REVERSE ORDER.
• USING THE MO.HUB WITH PLUS POLE CONNECTED TO VEHICLE FRAME (OLDER ENGLISH MOTORCYCLES) IS NOT POSSIBLE.
• INSTALLATION AND ELECTRICAL CONNECTION OF THE MO.HUB MAY ONLY BE CARRIED OUT BY A CERTIFIED MOTORCYCLE TECHNICIAN.
• ALL CABLE DIAMETERS MUST BE DIMENSIONED ACCORDING TO THE CURRENT FLOW (REFER TO CHAPTER 8.5).

Intended use

The mo.hub is a universal data interface between motorcycle and smartphone (and motogadget instrument). It connects the vehicle and the Smartphone via Bluetooth and enables the use of our „mo.ride“ app, with extensive vehicle management such as trip logs, maintenance activities, season progress, last trip data, etc.
The Bluetooth coupling process between smartphone and mo.hub and its confi guration in the app also take place. Further information at www.mo- ride.com

4.1 Areas of application
4.1.1 Smartphone and vehicle via OBD (On Board Diagnostics) interface For compatible vehicles, we provide suitable OBD plugs, which cables are need to be connected to the mo.hub terminals. The instructions for this are given in the coupling process within the „mo.ride“ app.
4.1.2 motogadget instrument and smartphone via the vehicle‘s instrument connector For compatible vehicles, we provide suitable instrument plugs, which cables are need to be connected to the mo.hub terminals. The instructions for this are given in the coupling process within the „mo.ride“ app.
4.1.3 motogadget instrument and smartphone via direct tap on the vehicle wiring harness For all vehicles without a BUS system, the signals are picked up directly on the vehicle wiring harness. The instructions for this are given in the coupling process within the „mo.ride“ app.

4.2 Device cold and warm start
During a cold start, the battery plus is connected to mo.hub T erminal 1 in addition to the vehicle earth (mo.hub T erminal 3). The device is initializing during a cold start. This process takes approx. 3s, which is indicated by a briefl y lit status LED.
During a warm start, vehicle earth and battery plus are connected. The device is in standby mode. The wakeup is done by ignition plus, switched by the ignition lock, at mo.hub T erminal 2.

4.3 Status LED
The following operating states are represented by the status LED:

• LED off: no Bluetooth connection or device off
• LED on: Bluetooth pairing active
• LED flashes once in 3s: Bluetooth connection established

4.4 Bluetooth pairing
Install the app mo.ride (from Android 8.0 / iOS13, availability according to smartphone manufacturer and model may be restricted).
Create and open a new vehicle in the garage. Now continue with button “pair hardware” and follow the further instructions.
Two methods to initialize the pairing process on the mo.hub:
A) Performing a cold start by connecting vehicle earth to mo.hub terminal 3 and battery plus to terminal 1. If allready connected, just unplug the large terminal strip from the mo.hub by pulling on it and then replug it. T ap the housing twice in quick succession with your index finger.
The action was successful if then the LED is continously lit. The pairing process can now be continued in the app.
OR
B) Switch the ignition on and off 10 times in quick succession. The action was successful when the LED is continously lit. The pairing process can then be continued in the app.
For this method, the following is required: connection vehicle earth to mo.hub termnial 3, battery plus to terminal 1 and ignition plus to termnial 2.
Note
When new or after a reset, the mo.hub is ready for pairing and can be coupled immediately after a cold start (LED lit).
The time window for the pairing process (LED lit) is 30s. After the time has elapsed, the LED will switch off and pairing process must be initialized again.
If a mo.unit blue and a mo.hub are used in a vehicle at the same time, the Bluetooth connection is only possible with one device. All other devices are connected to each other by cable via the motogadget LIN bus. Please follow the instructions in the pairing  process.
When reselling an already paired mo.hub, we recommend performing a reset to factory condition. This function is available after pairing; in the mo.hub settings of the mo.ride app.

Overview

Mounting the cable cover & cable guide

Mounting options

|

Connecting motogadget instruments to the mo.hub

8.1 motoscope mini and combi-frame or handle bar clamp

mo.hub
terminal no.| motoscope mini
wire color| combi-frame
wire color| HD handlebar clamp
wire color
---|---|---|---
3| black| orange | yellow | purple| orange | blue
H| red| white| red
S| yellow| |
T| white| |
U| green| |
V| | black| yellow
W| | brown| green
X| | red| purple
Y| | blue| black
Z| | green| white

8.2 motoscope tiny und motoscope classic

mo.hub terminal no.| motoscope tiny wire color| motoscope classic wire color
---|---|---
1| red|
3| black| black and white-green
H| brown| red
S| purple| yellow
T| orange| white
U| green| green
V| white| grey
W| yellow| white-orange
X| blue| blue
Y| | white-yellow

Connecting the vehicle with the mo.hub

9.1 vehicles without data BUS

9.2 BMW modells with LIN Bus
9.2.1 Vehicletype identifi cation
BMW models from 2015 with a 6 pin instrument plug with dimensions of approx. 9x10x22mm, are equipped with a LIN bus for communication between control unit and instrument.
9.2.2 Connecting the vehicle-specifi c plug and the battery cable to the mo.hub

9.2.3 Installation

1. Jack up vehicle, remove seat and tank, disconnect battery (fi rst minus, then plus)
2. Unscrew OEM instrument, unplug connector, unscrew OEM instrument carrier.
3. attach the motogadget instrument to the vehicle-specifi c motogadget retaining plate and connect the tail cable of the motogadget instrument to mo.hub
4. Connect motogadget vehicle-specifi c plug and battery cable to mo.hub
5. Screw the motogadget retaining plate with instrument to the fork bridge with the OEM screws.
6. Attach mo.hub to the upper frame tube with cable ties, avoiding collision pay attention to mo.hub housing and tank.
7. motogadget battery connection cable, OEM instruments connector plug and motogadget Instuments Lay the cable free of kinking and abrasion to the mo.hub and cable with cable ties attach to the frame. Allow enough play for steering movements.
8. Insert the plug of the OEM speedometer (not tachometer!) In the with motogadget Insert vehicle plug. The second OEM instrument plug (if available) with Protect heat shrink tubing from splash water.
9. The eyelet of the motogadget battery connection cable with the battery-plus connection terminal connect
10. Connect the battery (first plus, then minus)
11. Install the tank and seat

9.3 BMW Modells with CAN Bus
9.3.1 Vehicletype identifi cation
BMW models from 2010 – 2014 a 6 pin instrument plug with the dimensions of approx. 14.5×23.5x40mm, are equipped with a CAN bus for communication between control unit and instrument.
9.3.2 Connection of the vehicle-specifi c plug to the mo.hub

9.3.3 Installation

1. Jack up the vehicle, remove seat and tank
2. Unscrew OEM instrument, unplug connector, unscrew OEM instrument carrier.
3. attach the motogadget instrument to the vehicle-specifi c motogadget retaining plate and connect the tail cable of the motogadget instrument to mo.hub
4. Connect motogadget vehicle-specifi c plug and battery cable to mo.hub
5. Screw the motogadget retaining plate with instrument to the fork bridge with the OEM screws.
6. Attach mo.hub to the upper frame tube with cable ties, avoiding collision pay attention to mo.hub housing and tank.
7. OEM instrument connector and motogadget instrument cable kink and scuff -free Lay to the mo.hub and secure the cables to the frame with cable ties. Suffi cient Allow game for steering movements.
8. Insert the plug of the OEM speedometer into the vehicle with motogadget plug.
9. Install the tank and seat

settings for motogadget instruments

motoscope mini
Circ=2000 / ImpW=1 / ImpE=1
motoscope tiny, speedster, vintage
Circ=2000 / Pulse=1
motoscope classic, classic speedo, Chronoclassic, Chronoclassic speedo
Circ=200 / ImpW=4 / ImpE=1

12.3 Return and complaints
Before returning your mo.hub for technical inspection, contact our technical support.
Therefore, visit our website and follow the instructions in area “support”. Please provide the following informations completely: mo.hub serial no. (serial label on top of mo.hub). For returning an item follow the instruction in chapter “service” on our website.

Declaration of Conformity
Hereby, motogadget GmbH declares that the radio equipment type mo.hub is in compliance with Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the following internet address: https://manuals.motogadget.com/mo-hub/en/

WEEE directive
The wheelie bin symbol on the product or its packaging indicates that this product shall not be treated as household waste. In line with EU Directive 2002/96/EC for waste electrical and electronic equipment (WEEE), this electrical product must not be disposed of as unsorted municipal waste. Please dispose of this product by returning it to the point of sale or to your local municipal collection point for recycling. By doing this you will help conserve the environment.

Regulations
PRODUCT INFORMATION:
Manufacturer: motogadget GmbH
Model: mo.hub
FCC ID: 2AIF8-4005000
IC: 21495-4005000

FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
INFORMATION TO USER:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy.
If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the distance between the equipment and the receiver
• Connect the equipment to outlet on a circuit diff erent from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.

Canada – Industry Canada (IC)
This device complies with Industry Canada license-exempt RSS Standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

References

• mo.ride
• motogadget - parts for perfection
• motogadget - parts for perfection
• motogadget Manuals

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>