motogadget mo.switch Basic LED Instruction Manual

motogadget mo. switch Basic LED

Product Information

switched by an electronic switching module (i.e. MO.UNIT).
Manufacturer| moto gadget GmbH
Manufacturer Address| Wollenberger Str. 4i/j, 13053 Berlin
Contact Information| Tel. +49 (0)30-6900410-0, motogadget.com,
info@motogadget.de

Product Usage Instructions

Step 1: Review of Delivery
Please check the contents of the package upon delivery to ensure all components are present.

Step 2: Exclusion of Liability
Please note that Moto Gadget shall not be liable for any damage or defects resulting from negligence or failure to follow the operating and safety instructions provided.

Step 3: Safety Instructions
Read and follow all safety instructions provided in the user manual.

Step 4: mo. Switch combinations
The mo. switch basic LED can be combined with different numbers of push buttons depending on the desired functionality. Here are the available combinations:

Horn turn left
Lights turn right
5| Kickstarter & instrument or E-starter & no
instrument
Horn turn left / right
6| E-starter & instrument
Light starter or instrument
Horn turn left / right
Light starter/instrument

Step 5: Setup
Follow the instructions below to set up the mo. switch:

1. Insert the push-button inlay (A) into the housing (B).
2. Connect the push-button inlay to the housing using the push-button inlay clamping screw.
3. If needed, use the adapter sleeve (22mm to 1zoll) for installation.

Step 6: Installation
Mount all handlebar attachments and position them correctly. Clamp the mo. switch the housing to the handlebar. Then, drill four holes with a diameter of 5mm into the handlebar. Carefully deburr the holes inside and outside.

Step 7: Mounting and Wiring
For mo. switch basic LED with 2 buttons, use the following wiring:

MO.UNIT
Brown| Button A switches to ground and connects to the desired MO.UNIT
input
Green| Button B switches to ground, and connects to the desired MO.UNIT
input

For mo. switch basic LED with 3 buttons, use the following wiring:

MO.UNIT
White| Button A switches to ground and connects to the desired MO.UNIT
input
Yellow| Button B switches to ground, and connects to the desired MO.UNIT
input
Green| Button C switches to ground, and connects to the desired MO.UNIT
input

Declaration of Conformity
Motogadget GmbH declares that the product complies with EU directives. The full text of the EU Declaration of Conformity can be found at the following internet address: https://manuals.motogadget.com/mo-switch-basic-led

THIS PRODUCT CAN HANDLE CURRENTS OF MAX. 1A AND IS NOT SUITABLE TO SWITCH LOADS DIRECTLY. LOADS MUST BE SWIT-CHED BY A ELECTRONIC SWITCHING MODULE (i.e. MO.UNIT).

Thank you very much for purchasing a high-quality moto gadget product – Made in Germany.
Please read the following information and recommendations thoroughly and follow these in-structions during the installation and use of the product. No liability shall be assumed by motoga-dget for damage or defects resulting from negligence or failure to follow the operating and

contact: motogadget GmbH Wollenberger Str. 4i/j 13053 Berlin Tel. +49 (0)30-6900410-0 motogadget.com info@motogadget.de
Copyright © 2023 motogadget GmbH, Berlin. motogadget are registered trademarks of motogadget GmbH, Berlin, Germany.

Review of Delivery

All products from moto gadget are thoroughly checked to ensure they are completely fault-free when dispatched. Please check the received goods immediately for possible transport damage. If you find any damage or other deficiencies, please contact us immediately. In this regard, we refer to our General Terms of Business and Delivery, which are published at www.motogadget.com. Should a return of the received delivery be agreed upon, please note that we only take back goods in their original packaging. The mo. switch and its accessories must be returned within the legal period and without any traces of use. We shall not assume any liability for returns that are insufficiently insured or packed.

Exclusion of Liability

THE DEVICE AND ITS ACCESSORIES MUST BE INSTALLED BY A CERTIFIED MO- TORCYCLE TECHNICAN AND IN AN AUTHORIZED SERVICE CENTER. MOTOGADGET ACCEPTS NO LIABILITY FOR DIRECT OR INDIRECT DAMAGE OR SUBSEQUENT DAMAGE OF ANY KIND RESULTING FROM THE USE, INSTALLATION, OR CONNECTION OF THE DEVICE OR OTHER DELIVERED EQUIPMENT. THIS EXCLUSION OF LIABILITY PARTICULARLY INCLUDES DAMAGE TO PERSONS, MATERIAL LOSSES, AND FINANCIAL DAMAGES. THE USE IN AREAS OF PUBLIC TRAFFIC ENSUES AT THE USER’S OWN RISK. THE USE OF THE DELIVERED DEVICE AND ITS ACCESSORIES FOR RA- CING OR OTHER COMPETITIONS AS WELL AS FOR ANY USE NOT CORRESPONDING TO THE RECOMMENDED APPLICATION ALL WARRANTY CLAIMS SHALL BE INVALID

Safety Instructions

• THE VEHICLE BATTERY MUST BE COMPLETELY DISCONNECTED BEFORE ANY WORK ON THE VEHICLE’S ELECTRICAL FIRST, DISCONNECT THE NEGATIVE TERMINAL AND THEN THE POSITIVE TERMINAL. FOR RECONNECTION PROCEED IN THE REVERSE ORDER
• USING THE SWITCH WITH A PLUS POLE CONNECTED TO THE VEHICLE FRAME (OLDER ENGLISH MOTORCYCLES) IS NOT POSSIBLE.
• INSTALLATION AND ELECTRICAL CONNECTION OF THE UNIT MAY ONLY BE CARRIED OUT BY A CERTIFIED MOTORCYCLE TECHNICIAN.
• ALL CABLE DIAMETERS MUST BE DIMENSIONED ACCORDING TO THE CURRENT FLOW
• ALL ELECTRICAL CONNECTIONS IN THE WIRING LOOM AND AT THE CONNECTION TERMINALS HAVE TO BE CARRIED OUT FAILURE AT CONNECTING JOINTS MAY CAUSE CONTACT RESISTANCE AND LEAD TO HEAT GENERATION DURING HIGH CURRENT FLOW. THERE IS A RISK OF SERIOUS OR LETHAL INJURIES.

mo. switch combinations

Setup

Installation

• Mount all handlebar attachments and finalize their position. Clamp mo. switch the housing to the handlebar.
• Drill 4 holes with a 5mm diameter into the handlebar. Deburr the holes inside and outside carefully

Mounting and wiring

Guide the mo. switch connection cable through the handlebar hole at the clamping point and then through the second, central handlebar hole. Clamp the housing to the handlebar with the clamping screw. Carefully insert the push- button inlay into the housing and pull the cable piece by piece. Fasten the inserted push-button inlay to the housing with the supplied countersunk screw. Lay the connecting cable from the handlebars on the vehicle to the mo. unit without pulling or kin-king. The individual wires are connected as follows:

mo. Switch basic LED 2 buttons:

• black vehicle ground
• red terminal 15 (switched +12V), or AUX1 or AUX2 of the mo.unit
• brown button A switches to ground and connects to the desired mo. unit input
• green  button B  switches to ground, connects to the desired mo. unit input

mo. Switch basic LED 3 buttons:

• black vehicle ground
• red terminal 15 (switched +12V), or AUX1 or AUX2 of the mo. unit
• white button A switches to ground and connects to the desired mo. unit input
• yellow button B  switches to ground, connects to the desired mo. unit input
• green button C  switches to ground, connects to the desired mo. unit input

Declaration of Conformity
Hereby, Moto Gadget GmbH declares the product complies with EU directives. The full text of the EU Declaration of Conformity is available at the following internet address: https://manuals.motogadget.com/mo-switch-basic-led

References

• motogadget - parts for perfection
• motogadget - parts for perfection
• motogadget Manuals

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>