i-tec MySafe Advance 2.5 Inch USB-A User Guide

: June 12, 2024
: i-tec

Table of Contents

MySafe Advance 2.5 Inch USB-A
SPECIFICATION
SYSTEM REQUIREMENT
HARDWARE INSTALLATION OF SATA HDD
SOFTWARE INSTALLATION
PACKAGE CONTENT
SAFETY INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MYSAFE USB 3.0 ALUBASIC
User guide
P/N: MYSAFEU312

MySafe Advance 2.5 Inch USB-A

USB 3.0 Docking Station
Please read the entire instruction manual carefully. Detailed manual is available on our website www.i-tec.cz/en/ in the tab „Manuals, drivers“. In case of any issues, please contact our technical support at: support@itecproduct.com

www.i-tec.cz/en

SPECIFICATION

External USB 3.0 enclosure for 2.5” SATA I / II / III hard disk drives
Transfer interface: 1x USB 3.0
Compatible with all 2.5″ SATA HDD (with height up to 9.5 mm)
Solid Aluminum body for excellent heat dissipation and hard drive protection
Backward compatible with USB 2.0 / USB 1.1 devices
Supports the following speed data rates: SuperSpeed (5Gbps) / HighSpeed (480Mbps) / FullSpeed (12Mbps) / LowSpeed (1.5Mbps)
Hot Plug-and-Play
Active LED to indicate HDD status (it shines – HDD is connected, it twinkles – record/reading is underway)
Power supply 5 V, 900 mA
Weight: 60 g
Size: 126 x 76 x 13 mm

SYSTEM REQUIREMENT

Windows 7/8/8.1/10 – automatic installation of drivers from OS
Mac OS 10.x and higher – automatic installation of drivers from OS
Available USB port (we recommend using free USB 3.0 port to use maximal speed of HDD).

HARDWARE INSTALLATION OF SATA HDD

Proceed according to following instruction:

Remove the screws on the sides of enclosure and pull out internal part of enclosure.
Connect SATA connector of HDD to SATA port of the motherboard.
Insert HDD with internal part back to the enclosure.
Screw the screws back on the sides of enclosure.

SOFTWARE INSTALLATION

Windows 7/8/8.1/10 or Mac OS 10.x
After the connection to PC or Macintosh – system will detect equipment and will complete the driver installation automatically.
Note: For proper device functionality you have to format the HDD first. Follow the instructions below.

NEW HDD FORMAT

Right click „Computer“.
Select „Manage“.
Left click „Disk Management“.
Choose „Unallocated“ HDD with right capacity.
Right click disk area and select „New Simple Volume“, then click „Next“.
Use max. capacity of Volume and click „Next“.
Select „Assign the following drive letter“ and click „Next“.
Select „Format this volume with the following settings“ (use original settings). Click „Next“ and „Finish“.
Format of HDD will process. Format time depends on capacity of volume. After finish is HDD visible in OS.

PACKAGE CONTENT

External enclosure for 2.5“ HDD
USB 3.0 cable (50 cm)
Tool and screws
User’s Guide

SAFETY INSTRUCTIONS

Do not expose to extreme temperatures and air humidity.
Use the device on flat surfaces – you will prevent it from slipping and falling to the ground.
Save the user manual for a possible use later.

In cooperation with the service department:

Check functionality after falling to water or to the ground.
Check functionality when the cover is broken.
Send the device back if it does not work in accordance with the user manual.

FAQ
Available on our website www.i-tec.cz/en/ on the „FAQ“ tab of this product.

EUROPEAN UNION ONLY
NOTE: MARKING IS IN COMPLIANCE WITH EU WEEE DIRECTIVE
This equipment is marked with the above recycling symbol. It means that at the end of the life of the equipment you must dispose of it separately at an appropriate collection point and not place it in the normal domestic unsorted waste stream. This wil benefit the environment for all. (European Union only)

EU DECLARATION OF CONFORMITY

Manufacturer :
i-tec Technologies s.r.o., Kalvodova 2,
709 00 Ostrava – Mariánské Hory, Czech Republic
declares that this product
Product
Naam: i-tec MYSAFE AluBasic 2,5″ USB 3.0 SATA Case
Model
MYSAFEU312 / K2501U3_K2501A/B/C-U3S

Determination
Product is determined for using in PC as equipment.
Meets the essential requirements according to:
EC Directive 2014/30/EU, and 2011/65/EU
EMS (For EMC):
EN 55032:2015+A11:2020+A1:2020; EN IEC 61000-3-2:2019+A1:2021; EN 61000-3-3:2013+A1:2019
EN 55035:2017+A11:2017;
RoHS:
2011/65/EU; (EU) 2015/863
and it is safety under conditions of standard application

Additional information
Identification Mark

Ostrava
01. 09. 2022 Ing. Lumír Kraina
Executive Name and Signature

FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.