i-tec U3HUB778 USB 3.0 Metal Charging Hub User Guide
- May 15, 2024
- i-tec
Table of Contents
USB 3.0 METAL CHARGING HUB
4X USB-A 3.0 Port
User guide
P/N: U3HUB448
U3HUB778 USB 3.0 Metal Charging Hub
Please read the entire instruction manual carefully.
Detailed manual is available on our website
www.itec.cz/en/ in the tab „Manuals, drivers“. In
case of any issues, please contact our technical support at:
support@itecproduct.com
https://i-tec.cz/en/produkt/u3hub448-2/
INTRODUCTION
i-tec USB 3.0 Metal Charging HUB is an ideal companion for everybody who does
not have enough USB ports in his/her notebook, ultrabook or PC and who has to
constantly connect and disconnect his/her favorite USB equipment such as flash
disks, mobile phones, tablets, digital cameras, MP3 players, printers, etc.
This HUB offers 4 USB 3.0 ports with the Plug & Play function and standard USB
charging – the HUB will automatically detect connected equipment for USB
charging. The USB 3.0 interface is important mainly for data transfers from
USB 3.0 memory cards and flash disks which will use its high transfer speed
most.
The advantage is included external power adapter which you can use for backing
up data on external hard drives or for connecting high power consumption
devices which are powered directly from the USB port.
This HUB does not require installation of drivers. You will just connect it
by the USB cable to your computer and immediately you can start using it. This
HUB has a built in overcurrent protection of your computer in case of short
connection on the peripheries. The interface is compatible with USB 2.0 / 1.1.
Thanks to its compact dimensions and low weight it is an ideal companion to
your notebook when traveling.
SPECIFICATION
- 4x USB 3.0 port for connecting USB equipment
- 1x USB 3.0 cable for connecting the HUB to a notebook / PC
- Transfer rate up to 5 Gbps
- USB charging detection mechanism for mobile devices
- Plug & Play function
- Overload and overcurrent protection
- LED diode
- Storage temperature -10~85 °C
- Working temperature 0–40 °C
- Power adapter: input AC 100–240 V, 50–60 Hz, 0.8 A; output DC 5.0 V, 2.0 A
- OS Windows 7 32/64bit, 8 32/64bit, 8.1 32/64bit, 10 32/64bit, macOS X 10.x or higher
- Product dimensions 112 x 37 x 18 mm
- Product weight 70 g
DESCRIPTION
- 4x output USB 3.0 ports for connecting USB equipment
- LED diode – the diode is ON when the HUB is connected to the power adaptor or to a USB port of a notebook / PC
- Input for connecting the power adaptor
- USB 3.0 cable type A for connecting to a notebook / PC
CHARGING
You can use external power adapter, if you connect printer, scanner or other high power consumption devices to USB ports in HUB (power adapter is included). Respect the basic rules while using this power adapter (for ex. do not let in reach of children, if the adapter is in 230 V circuit, do not put it into the water and so on).
CHARGING
The HUB supports charging of the connected USB mobile equipment such as
smartphones (including iPhone and Samsung phones), e-book readers, multi-media
players, GPS navigators, and tablets (e.g., Asus, Toshiba, GoClever,
Prestigio, Emgeton, Sencor). Using the original cable connect the equipment to
be charged to the USB port of the HUB. At the same time the power adaptor
needs to be connected to the HUB as well.
INSTALLATION IN WINDOWS 7 / 8 / 8.1 / 10 AND
HIGHER, MACOS X AND HIGHER
The HUB is installed automatically, no need install drivers.
Connect the connector of the power adaptor to the HUB and connect the power
adaptor to a socket outlet with 230V. Then plug the HUB via USB cable into
available USB port (USB 3.0, 2.0 or 1.1 standard) of your notebook / PC and
follow the on-screen instructions. The HUB will be installed and displayed in
Device manager as “Generic USB Hub” and “Generic USB SuperSpeed Hub”.
SYSTEM REQUIREMENTS
Windows 7 32/64bit, Windows 8 32/64bit, Windows 8.1 32/64bit, Windows 10 32/64bit, macOS X 10.x or higher
PACKAGE CONTENTS
- i-tec USB 3.0 Metal Charging HUB 4 Port with bulit-in USB cable (28 cm)
- Power adapter (DC cable 120 cm)
- Quick Start
SAFETY INSTRUCTIONS
-
Do not expose to extreme temperatures and air humidity.
-
Use the device on flat surfaces – you will prevent it from slipping and falling to the ground.
-
Save the user manual for a possible use later.
In cooperation with the service department: -
Check functionality after falling to water or to the ground.
-
Check functionality when the cover is broken.
-
Send the device back if it does not work in accordance with the user manual.
External power supply exclusively for use with U3HUB448.
FAQ
available on our website www.i-tec.cz/en/ on the „FAQ“ tab of this product.
EUROPEAN UNION ONLY
NOTE: MARKING IS IN COMPLIANCE WITH EU WEEE DIRECTIVE
This equipment is marked with the above recycling symbol. It means that at the end of the life of the equipment you must dispose of it separately at an appropriate collection point and not place it in the normal domestic unsorted waste stream. This wil benefit the environment for all. (European Union only)
EU DECLARATION OF CONFORMITY
Manufacturer i-tec Technologies s.r.o., Kalvodova 2, 709 00 Ostrava –
Mariánské Hory, Czech Republic declares that this product
Product : i-tec USB 3.0 Metal Charging HUB 448 – 4port
Model : U3HUB448 / UHB348
Determination : Product is intended for use as an acessory for PCs.
EC Directive 2014
EMS (For EMC) : EN 55032:2012; EN 55035:2017; EN 61000-3-2:2014; EN
61000-33:2013
For Electrical Safety : EN 62368-1:2014+A11:2017
RoHS: 2011/65/EU; EU 2015/863 and it is safety under conditions of
standard application Signed for and on behalf of:
Ostrava 16. 01. 2024
Ing. Lumír Kraina
Executive Name and Signature
Amendment to user manual providing all necessary information required by
COMMISSION REGULATION (EU)
2019/1782. (This product meets all the requirements laid down by the above
regulation).
| Information published | Value and precision | Unit |
|---|---|---|
| Manufacturer’s name or trade mark, commercial registration number and address |
Shenzhen Xingzhongguangmai
Electronic Co.,
LtdBantian, Shenzhen,
Guangdong,
China
Model identifier| XZGM-052000FU
Input voltage| 100–240| V
Input AC frequency| 50/60| Hz
Output voltage| DC 5.0| V
Output current| 2| 2
Output power| 10| W
Average active efficiency| 84.9| %
No-load power consumption| 0.05| W
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply within the limits of a
Class B digital device pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>