KTC HWiFi6-1 Highly Integrated Dual-Band WLAN Module User Manual

HWiFi6-1 user manual

Module Introduction

HWiFi6-1 is a highly integrated dual-band WLAN module that contains a WLAN AP module (BLM7621AX7) and a WLAN WiFi module (BL-M8832AU1).
The BL-M7621AX7 module is built from MT7621DA, MT7905 and MT7975. It combines the 2T2R dual-band WLAN subsystem. The module integrates dual-core MIPS1004Kc (880MHz), HNAT/HQoS/Samba/VPN accelerator, 1-port GbE switch and 1 UART port for debugging. The module is compatible with IEEE 802.11a /b/g/n/ac/ax standard. A WLAN 2.4G RF link with 40MHz bandwidth can support a physical rate of 573Mbps. A WLAN 5.8G RF link with 80MHz bandwidth can support a physical rate of 1201Mbps.
The BL-M8832AU1 incorporates the 2T2R dual-band WLAN subsystem. Compatible with IEEE 802.11a /b/g/n/ac/ax standards, the module provides physical layer rates of up to 1200Mbps, delivers feature-rich wireless connectivity to a high standard, and delivers reliable, cost-effective high throughput from long distances.
Functions of BL-M7621AX7 module:
Operating frequency: 2.4 ~ 2.4835GHz or 5.15 ~ 5.85GHz (reserved 5.926 ~ 7.125Ghz WLAN band)
WLAN functions:
Dual-band 2T2R mode with 20/40/80Mhz bandwidth is supported Supports MU-MIMO receiving and MU-OFDMA sending/receiving Transmit/receive beamformers are supported
Support DBDC (Dual frequency dual concurrent)
Embedded MIPS1004Kc (880MHz, dual-core) with 32KB I cache and 32KB D cache per core Functions of BL-M8832AU1 module:
Operating frequency: 2.4 ~ 2.4835GHz or 5.15 ~ 5.85GHz
Host interface: Compatible with USB3.0 and USB2.0 for WLAN
IEEE standard: IEEE 802.11a/b/g/n/ac/ax
Wireless data rates are up to 573.5Mbps or 1201Mbps

Detailed Specification：

Antenna size:160161.0mm
PCB module size| 1397316.1mm (LWH)
WiFi6 module size| 167.88028.2
Power source| DC 12V±0.5V(power range 5~14V) @ 1500 mA (Peak for 12V)
Working temperature| -10℃ to +40℃
Working humidness| 10% to 95% RH (Non-Condensing)

PIN Description：

P: Power or Ground; I/O: In/Output; I: Input; A I/O: Analog In/Output; AI: Analog Input;
AO: Analog Output; RF: Analog RF Port or RF Ground;

Structurion & PCBA Size

1. PCBA sizePCB size: 1397316.1mm(LWH; Tolerance: ±1mm)
   IPEX / MHF-1 port size: 2.63.01.2mm (LWH, Ø2.0mm)Antenna size: 160161mm(LWH; Tolerance: ±0.2mm)

2. WiFi6 module size：

Sofeware feature

1. Screen sharing：WiFi6 module, can create LAN, realize ISO device or Android device or PC device screen sharing, sharing content including but not limited to video, pictures, files, etc.；
2. Wireless：WiFi6 module，It can realize the interconnection of the conference panel network without wiring, and use the network function.
3. Mobile hotspot: WiFi6 module, can function as a router, to achieve the conference tablet connected to the network, other network equipment connected to the machine hot spot function to be able to access the network;

Warning：
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation

FCC warning:

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body
IC warning:

This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>