elk HOME 89966-6 34 Inch Wide 6 Light Chandelier Installation Guide
- June 16, 2024
- elk HOME
Table of Contents
elk HOME 89966-6 34 Inch Wide 6 Light Chandelier
Specifications
- Item #: 89966/6, 89976/6
- Manufacturer : Elk Home
- Website : www.elkhome.com
WARNING: DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.
WARNING: This fixture is intended for installation by the National
Electrical Code (NEC) and all local code specifications. If you are not
familiar with code requirements, installation by a certified electrician is
recommended. Before assembly, remove all parts and part packages from the box.
If anything is missing, please contact the retailer from which the product was
purchased.
INSTALLATION
-
Carefully pull house wires down out of the junction box so house wires are easily accessed to connect fixture wires.
-
If the screw collar loop (W) is already attached to the mounting bracket (A), proceed to Step 3. To assemble screw collar loop (W) to mounting bracket (A): Hold mounting bracket (A) so the head of the ground screw is pointing down towards the floor. Hold threaded pipe so two hex nuts already attached to threaded pipe (E) are pointing down towards the floor. From the side of the mounting bracket with the ground screw head, screw the short end of the threaded pipe (E) into the hole in the centre of the mounting bracket (A) until the hex nut on threaded pipe (E) touches the mounting bracket. Thread hex nut (V) onto the end of the threaded pipe (E). Tighten hex nut (V) to secure threaded pipe (E) to mounting bracket (A). Thread screw collar loop (W) onto the end of threaded pipe pointing down towards the floor. Tighten the screw collar loop up against the hex nut on the threaded pipe (E).
-
Place mounting bracket (A) up against the junction box. Screw collar loop (E) should be pointing down towards the floor. Align each slot in mounting bracket (A) with each hole in the junction box.
-
Thread one junction box screw (B) into each slot in the mounting bracket (A) and into holes in the junction box. Tighten junction box screws (B) to secure mounting bracket (A) to the junction box.
CAUTION: Make sure house wires are still easily accessible. DO NOT pinch wires between the mounting bracket and ceiling.
-
Carefully push fixture wires from the top of the fixture body (O) up through the bottom of the centre stem (M). Pull fixture wires taut. Screw the centre stem (M) onto the top of the fixture body (O).
-
Slip fixture wires through the hole in the top trim (N). Slip hole in top trim (N) over top of centre stem (M).
-
Push fixture wires up through the bottom of the loop (L). Pull fixture wires taut. Screw the bottom of the loop (L) onto the top of the centre stem (M).
-
Connect one locking link (G) to loop (L).
-
Determine the desired hanging height of the fixture. Cut chain (H) to length to achieve the desired height.
-
Slip the chain link at the end of the chain (H) onto the locking link (G) on loop (L).
-
Weave fixture wires through chain links, skipping every other chain link.
-
Slip the threaded ring (F) down over the end of the chain (H).
-
Position canopy (D) so outside of the canopy is pointing down towards the fixture. Slip hole in canopy (D) over the end of the chain (H).
-
Strip 3/4” of insulation from the ends of fixture wires.
-
Carefully push fixture wires up through the hole in the screw collar loop (W) attached to the mounting bracket (A) and the out end of the threaded pipe inside the junction box. Carefully pull fixture wires so they are easily accessible to connect to house wires.
-
To aid in connecting fixture wires to house wires, temporarily connect a second locking link
(G) to link at the end of the chain (H) and to screw collar loop (W). -
Slightly loosen the ground screw on the mounting bracket (A). Do not completely remove the ground screw. Wrap house ground wire (copper) around the ground screw, leaving enough ground wire
to attach to the fixture ground wire. Twist the end of the fixture ground wire and the end of the house ground wire together. Twist wire nut (C) onto the ends of the wires. Completely tighten wire nut (C). Reference the chart below for correct wire connections.
Connect Supply (House) Ground Copper Wire to:
Bare Copper Wire or,
Bare Silver Wire or,
Green Insulated Wire.
18. Twist the end of the house lead wire (black) and the end of the fixture lead wire together. Twist wire nut (C) onto the ends of the wires. Completely tighten wire nut (C). Twist the end of the house neutral wire (white) and the end of the fixture neutral wire together. Twist wire nut (C) onto the ends of the wires. Completely tighten wire nut (C). Reference chart to the right for correct wire connections.
19. Wrap electrical tape (not included) around wire nuts (C) and wires. Ensure wires are securely fastened into wire nuts.
20. Carefully push all wires and wire nuts into the junction box.
Connect Black Lead Supply (House) Wire to:| Connect White Neutral Supply
(House) Wire to:
---|---
Black Wire or,| White Wire or,
Parallel Cord (Round and Smooth) or,| Parallel Cord (Square and Ridged) or,
No printed words on wire insulation or,| Printed words on wire insulation or,
Insulated Wire (other than green)
with Copper Conductor.
| Insulated Wire (other than green)
with Silver Conductor.
*When parallel wire (SPT 1 & SPT 2) is used: The lead wire is round in shape or smooth.
The neutral wire is square in shape or ridged.
- Remove the second locking link (G) from the last link on chain (H) and screw collar loop (W).
- Raise canopy (D) up to ceiling. Pass hole in the canopy (D) over screw collar loop (W). Position canopy (D) up against the ceiling.
- Raise threaded ring (F) up to canopy (D). Screw threaded ring (F) onto screw collar loop (W). Tighten the threaded ring (F) to secure the fixture to the ceiling.
- Attach a second locking link (G) to the link at the end of a chain (H). Attach locking link (G) at end of the chain (H) to loop on screw collar loop (W).
- Set each shade (K) down over the socket.
- Screw recommended bulbs (E12 candelabra bulb type, not included) into sockets. Verify the correct bulb wattage marked on the socket of the fixture. WARNING: DO NOT exceed maximum bulb wattage.
FAQ
- Q: What should I do if any parts are missing?
- A: If any parts are missing, please contact the retailer from which the product was purchased.
- Q: What is the customer support contact number?
- A: For any questions or assistance, please call 800-613-3261 during M-F 8:00 AM-6:00 PM ET.
ANY QUESTIONS CALL: 800-613-3261
M-F 8:00AM-6:00PM ET
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>