TOOLOTS TD3WS Benchtop Low Speed Centrifuge Instruction Manual

TD3WS Benchtop Low Speed Centrifuge
Instruction Manual

Benchtop low-speed centrifuge
TD3WS
operation instruction
Before use, please read the operation
instruction handbook

Safety alerts and precautions:

Safety alerts：

1. Before use, please read the operation instruction handbook.
2. Do not use in wet, hot or dusty locations to avoid instrument failure.
3. When the instrument is running, it must not move the instrument and must not open the door cover of the instrument.
4. The countertop of the installation instrument should be solid and flat, there should be no shaking phenomenon, all four rubber machine feet should be in full contact with the countertop and uniform force.
5. Centrifuge tube added liquid as evenly as possible, if the difference between the addition will produce large vibration, at this time should be stopped to check, so that the addition meets the requirements, centrifugal test tube must be placed in even symmetry, not singular into or asymmetrical into the rotor.
6. After each use, open the instrument door cover, allow the water in the centrifugal cavity to evaporate, and clean the inner cavity of the instrument. The instrument must have a reliable ground wire when using a power supply.

Precautions：

1. Do not strongly collide, vibrate or re-throw the instrument to avoid non-serviceable consequences of damage to the mechanical or electrical parts of the instrument.
2. Do not use the instrument in wet or hot places to avoid extensive damage to the electrical part of the instrument.

【Product Name】Centrifuge 【Model】TD3WS 【Product performance structure and composition】It consists of a control system, centrifugal cavity, drive system, rotor, refrigeration system (If it is a refrigerated centrifuge) and safety
protection.
【Scope of application】This product is suitable for use by trained professional operators and technicians.
【 Taboo 】 It is taboo to use without professional operators or personnel without relevant operational qualifications.
【Precautions】See above.
【Alerts and suggestive content】Stop prompts
【Operating instructions】See below
【 Label, packaging identification sample 】 Please read the instructions

【Storage conditions/methods】
Rooms with ventilation/drying/light avoidance/non-corrosive gases should be stored.

Overview

This manual adapts to TD3WS benchtop low-speed centrifuges can be widely used in biochemistry, genetic engineering, radioimmunology and other fields, is an ideal experimental instrument for research institutes. This machine  uses DC variable frequency motor, microcomputer control, liquid crystal display, lift speed, low noise, small vibration, electronic door lock safe and reliable. (See Table 1/Table 2 for major technical performance)
Table 1: Technical parameters

Table 2: Instrument rotor parameters

angle
rotor| 4000 rpm| 2200 xg| 6 x 15 ml| 012.4 x 106
NO.2| 4000 rpm| 2200 xg| 8 x 15 ml| 012.4 x 106
NO.3| 4000 rpm| 2200 xg| 12 x 7 ml| 012.4 x 106

structural characteristics:

1. The machine uses brushless DC motor direct drive, No
   sparks in operation, No toner pollution, the noise is small, can
   meet the requirements of laboratory work.

2. The use of special shock-absorbing system, shock-absorbing
   effect is good.

3. The use of microcomputer control, high speed control
   accuracy, touch panel can facilitate the user to accurately set
   operating parameters.

installation requirements:

1. The instrument is placed on a solid work surface (preferably
   reinforced concrete countertop).

2. The instrument should be placed on the table level, to ensure
   reliable contact between the four feet and the table.

3. Indoor should be dry, good ventilation, relative humidity
   remains below 85%, indoor temperature should be 5 °C to 35 °C

Operating procedures:

1. Open the door cover, install the rotor, screw tight.
2. After the addition of centrifuge tube into the rotor, centrifuge tube must be placed in even symmetry (centrifuge tube test fluid visually uniform), after the hand gently rotate the rotor.
3. Close the door cover, pay attention to make the door cover locked, finish by hand to check whether the door cover is closed, otherwise the centrifuge does not run.
4. Plug in the power supply and press the power switch (the power switch is on the back of the centrifuge).
5. Set speed or time: centrifuge in the stop, start state, speed and time parameters can be set according to the requirements of the experiment.
   (1) When setting the speed and time, press the “▲” or “▼ ” key to the experimental requirements value, release the key, the digital tube flashes 3 times, you can automatically confirm the set parameters.
   (2)When the above two steps are completed, and then press the start button centrifuge to start running, the control panel shows the speed and the remaining centrifuge time.
   (3)Centrifuge countdown to “0”, automatically stop, speed of 0, buzzer prompt.
   (4)In operation, press the “RCF” key, showing the current speed of centrifugal force.
   (5)When the rotor stops, open the door cover to remove the centrifuge tube.
   (6)Turn off the power after use.

Safety precautions:

1. Centrifuge in operation, Do not move centrifuges, Do not force open the door cover.
2. The per centrifuge should be solid and flat, and the four rubber machine feet should be in contact with the table and evenly stressed, so as not to produce vibration.
3. Centrifuge tube liquid as far as possible visual uniformity, if the difference between the addition of liquid too large operation will produce large vibration, at this time should stop inspection, so that the addition meets the  requirements, centrifugal test tube must be placed in even symmetry.
4. If there is a centrifugal test tube rupture in operation, should be immediately stopped processing.

Benchtop low-speed centrifuges
Packing list

Product form picture

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>