TOOLOTS 2300W Multifunctional Ceramic Tile Cutting Machine Instruction Manual
- October 30, 2023
- TOOLOTS
Table of Contents
2300W Multifunctional
Ceramic Tile Cutting Machine
Instruction Manual
FRODUCTION TO CUTTING MACHINE PARAMETERS
‘Analysis of Ingenious manufacturing parts
- Product Name: electric tile cutting machine
- Fuselage material: reinforced aluminum fuselage
- Slide rail material: solid steel
- Automatic water adding: Yes
- Motor power. 2300W
- Cutting depth: 30mm
- Product features: linear cutting, chamfering, diagonal cutting. ground mosaic, edge grinding and soothing
Three specifications are available
| Model 800: | the total length:1100mm | the maximum cutting length:80cm |
|---|---|---|
| Model 1000: | the total fength:1300mm | the maximum cutting length: 100em |
| Model 1200: | the total tength:1500mm | the maximum cutting length:120em |
ELECTRIC BOX OPERATION GUIDE
-
Gear adjustment
Press + to speed up and – to slow down. -
Length adjustment: Long press the “manual mode” for 3 seconds, and the individual bits of the display will jump. Press “+” or “-” to lengthen and decrease. Briefly press the manual mode for ten digit runout once, and then press the hundred digit runout once. After the length is set, confirm it according to the automatic mode. 3. Manual mode : Short press the manual mode, press “+” and then press to start, it is forward, short press “-” and then press to start, it is backward.
-
Automatic mode: Short press the automatic mode, press start to move forward automatically, and move backward automatically after the length is completed 5 remote control matching long press the stop key for 3 seconds, and the display displays press the remote control to match.
Automatic payment operation button| Remote control operation key|
---|---|---
| 1. Linear cutting
Accurately measure the required size from the cutting piece, fix the guiding
rule and turn on the circulating water| Note: the hardness of ceramic tiles is
different, and the cutting speed is adjusted, which is not easy to be too
fast
| 2. Diagonal cutting
Turn on the infrared to align the tip of (the ceramic tile, align the tip of
the ceramic tile with the cutting piece at the other end, and then fix the
semicircle to fix the backer| Note: the hardness of ceramic tiles is
different, and the cutting speed is adjusted, which is not easy to be too
fast
3. Polygon cutting
Draw the cutting line with an angle ruler, align the drawn line with infrared,
and then fix iton the edge with a semicircle
4. Grinding angle while cutting
Use 502 glue to stick the cutting part and the edging wheel together
concentrically. Aner the glue is dried and fixed, install the motor and adjust
the height
5.45 degree inner chamfer Adjust the machine head to 45°, turn the back of the ceramic tile upward, and adjust the size according to the required width
6. Rounding edge
Adjust the backer to the grinding size
Adjust the cutting depth Note: the hardness of ceramic tiles is different, and
the cutting speed is adjusted, which is not easy to be too fast
6 slotting
Adjust the backer and the cutting depth.
The water spray nozzle must be aligned with the contact point between the
edging wheel and the ceramic tile
Note: the hardness of ceramic tiles is different, and the cutting speed is
adjusted, which is not easy to be too fast
7 water pump
The water pump should be cared for frequently and cleaned after work
Infrared ray adjustment
1.2 point is the light up and down adjustment
3.4 point is the left-right adjustment of light
Extend 1200mm and connect the long extension rod with the short extension rod.
Cutting depth adjustment Slightly loosen the fixing screw and adjust it
according to the required cutting depth
Track and slider maintenance
Always refuel the track and pull it back ten to twenty times
Head left and right adjustment
Slightly loose screw Then adjust it to the left or right according to the
actual situation. When the screw is tightened (the screw is loosened first),
it is adjusted to the right, and when the screw is tightened (the screw is
loosened first), itis adjusted to the left
ELECTRIC CERAMIC TILE STONE CUTTING
SAFETY TIPS
- Diamond cutting blades that do not meet the performance specified by the manufacturer shall not be used.
- Broken, deformed or cracked cutting pieces shall not be used.
- Do not start the cutting machine when the cutting blade is in contact with the workpiece.
- Replace the cutting blade, adjust the cutting depth and repair the water pipe. Press and hold the leakage protection switch on the plug of the cutting machine, and the cutting machine is in the power-off state.
- Keep your hands away from the sawing area or diamond saw blade. If you hold the safe place of the cutting machine with both hands, you will not be hurt by the saw blade.
- Always use the diamond saw blade with proper size and axial shape. If the diamond saw blade is inconsistent with the parts of the cutting machine, it will cause eccentric operation and damage the equipment.
- Do not use damaged washers and bolts with inconsistent dimensions. The use of damaged washers and bolts with inconsistent dimensions will lead to improper operation and inaccurate normal operation of the equipment.
- When using this machine for automatic cutting, first slow down the cutting speed and slowly increase the speed, So as to avoid the damage of the cut object and the blocking of the machine.
- After cutting, the motor idles for two minutes, which is conducive to the discharge of water vapor inside the motor and prolong the service life of the motor.
Please keep this manual
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>