TOOLOTS CH84 Heat Transfer Press Instructions

TOOLOTS CH84 Heat Transfer Press

Product Information

The heat transfer press is a solid steel welded framework that is scratch- resistant. It has an intelligent digital time and temperature control panel with a memory function and automatic countdown and alarm. The machine is good for heat transfer printing on t-shirts, bags, puzzles, mouse pads, etc. It comes in four different platen sizes: 40 x 80 cm, 60 x 80 cm, 70 x 90 cm, and 80 x 100 cm. The voltage for the machine is 220/110 V, and the power ranges from 3 KW to 9 KW depending on the platen size. The time range is from 0-999 seconds, and the temperature range is from 0-299 degrees Celsius.

Product Usage Instructions

1. Only use the heat transfer press as intended.
2. Keep children away from the machine.
3. Make sure to use the correct outlet before using the device.
4. Burns can occur from contact with a hot surface, so avoid touching it.
5. Use an air compressor with at least 35L capacity.
6. Turn off the device when not in use and remove the power plug.

How to Print a T-Shirt?

1. Set the temperature and time using the temperature setting button (TEMP), temperature up arrow key, temperature down arrow key, and time setting button (TIME).
2. Place the T-shirt on the platen.
3. Put the design face down on the t-shirt.
4. Press the handle with the desired pressure until it clicks into place.
5. Wait for the automatic countdown and alarm to finish.
6. Lift the handle and remove the t-shirt from the plate.

The Question Prompt for the Failure Printing

We are sorry, but we do not understand the question prompt for the failure printing. Could you please provide more information or clarify the question?

TRANSFER PARAMETERS

Platen Size (CM) Platen Size (Inches) Voltage (V)

• 40 x 80 16” x 32” 220/110
• 60 x 80 24” x 32” 220/110
• 70 x 90 28” x 35” 220/110
• 80 x100 32” x 39” 220/110

Power (KW) Time Range (Sec) Temperature Range(℃)

• 3 0-999 0-299
• 6 0-999 0-299
• 8 0-999 0-299
• 9 0-999 0-299

NOTICE

1. Use the heat transfer press only as intended
2. Please keep children away from the machine
3. Make sure the correct outlet is before using the device
4. Burns can occur from contact with a hot surface
5. Please choose an at least 35L air compressor
6. Turn off the device when not in use and remove the power plug

Solid steel welded framework, scratch-resistant, Intelligent digital time &temp control panel with memory function, Automatic countdown and alarm, Good in heat transfer printing on t-shirts, bags, puzzles, mouse pads, etc.

Product Characteristics

1. Fully digital temperature and time control, LCD displays show the temperature and time;
2. The processing time is electronically controlled, and the finalization of process steps is warned by light
3. The working surface is covered by imported heat-resistant cloth, so it has a long working life and is easily cleaned.
4. The pressure can be adjusted easily
5. A heat-resistant silica-gel sponge is placed on the motherboard, so the machine can print many kinds of products.
6. The heating pipeline is connected to a heating plate, so the working surface can be heated even for a short period, so the machine is safe and durable.
7. Aluminum heat plate, heating uniformity on the surface.
8. Teflon coated on the heat plate, a convenient and attractive appearance.
9. The silicon pad can endure a maximum of 300 degrees without any distortion

Read before operating:

• Be sure to operate with safe ground wire!!!
• Check the voltage before using it. Turn off the power supply.
• When using the machine, please don’t heat the machine without operating it for a long time.
• When finish the transfer press, please turn off the machine
• When heating the machine, don’t touch the up heat plate in case of scald.
• When you press the handle, if you feel the pressure is too much and hard to press it, please adjust the using pressure by hand. Keep children away from the machine.

Setting Temperature & time

1. “TEMP” temperature setting button;
2. Temperature UP Arrow Key &Down Arrow Key;
3. “TIME” time setting button

Operation (The temperature shows C degrees)

• No.1: Turn the power switch on, and press the power button, then the power indicator is lightened
• No.2: Setting the temperature, press the “TEMP” key, then, press the UP arrow key or down arrow key, and set the right temperature. ( for the T-shirt: 180 C degrees.)
• When the temperature reaches the right range, the indicator on the top of the temperature adjuster is switched off.
• Then the following operations can be conducted.
• No.3 Setting time, Press the “TIME” key, then, press the UP arrow key or down arrow key, and set the right time. (For T-shirt: 15-20 sec.)
• No.4 Flatly place the cloth on the lower printing plate, then cover the printing paper (please note the working surface of the paper), and push the handle down to the specified point.
• , Please note that the force should not be more than 25 Kg at this time, or otherwise. The handle will be transformed.
• a. Sublimation Heat Transfer: Temperature 170~190°C,Time: 15-20sec.
• b.Film heat transfer: Temperature 110-150°C, Time: 8~15 sec.
• c.Foam Heat Transfer: Temperature 120-160°C, Time:8-15 sec
• d. Fot-fix rhinestone: Temperature 160-180°C, Time: 10~15 sec.

How to print a T-shirt?

• A. Take a digital photo Print it out on sublimation paper with sublimation ink in your printer (mirror image printing). Cut the picture size to be large as you want, put it on your tee shirt, and fix it with adhesive tape.
• B. Puta T-shirt in the machine. (put the printed sublimation paper on the shirt properly.)

1. Get ready on the power, press the power button, and the indicator is lighted!
2. Adjust the temperature ( 170°C- 180″°C) and time ( about 15-20 seconds). When the temperature reaches the right degree, the top temperature indicator will be extinct.
3. Put the heating flat down (please note the right surface of the paper). Please note that the pressure should be not too much. or too little!
4. When the temperature gets to the sct time. ce buzzer rings (please turn off (the bullion and raise) Your customized T-shirt is done! very Simple:)

THE QUESTION PROMPT FOR THE FAILED PRINTING

• A . the color is lighter: the temperature is too low, or the pressure is not even, or the time is too short
• B . The design is indistinct: the time is too long and leads to ink diffusing
• C . The design has no luster: the pressure is too high or the temperature too high .
• D . Part of the design is indistinct: the heat printing zone or the heating is not even.
• E . Scar on design: heat printing time is too long.
• F . Dept of color is not the same: pressure is not even or the coating is not even.
• G. Paper stick to the object: the temperature is too high, or the coating of the object is not good.

Print your own customized product you need

1. One inkjet printer/six colors printer (For example Epson R-230/R270/R290/T50)
2. One CISS (Continuous ink supply system) Different models of Inkjet Printers will need different CISS
3. Sublimation ink
4. High-temperature resistant tape;
5. Sublimation paper; or Heat transfer fabric paper

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>