BEGA 24149 Wall Ceiling Light LED Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

Instructions for use
Product description
Installation
Cleaning · Maintenance
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 24149 Wall Ceiling Light LED Instruction Manual

Instructions for use

Dimension

Application
Unshielded wall luminaire with integral passive infrared motion and light sensor. A luminaire made of aluminium alloy and crystal glass. The integrated passive infrared motion and light sensor responds to heat emission in the dark and therefore activates in case of human or animal movement in the vicinity of the luminaire. Configuration is done via Bluetooth and the free BEGA Tool app.

Lamp
Module connected wattage 6.5 W
Luminaire connected wattage 9 W
Rated temperature ta=25 °C
Ambient temperature ta max=30 °C

24 149K3
Module designation LED-1182/830
Colour temperature 3000 K
Colour rendering index CRI >80
Module luminous flux 1100 lm
Luminaire luminous flux 838 lm
Luminaire luminous efficiency 93,1 lm/W

24 149K4
Module designation LED-1182/840
Colour temperature 4000 K
Colour rendering index CRI >80
Module luminous flux 1155 lm
Luminaire luminous flux 881 lm
Luminaire luminous efficiency 97,9 lm/W

Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e.g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Product description

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Crystal glass, white inside
Silicone gasket 2 mounting holes ø 4.5mm
Distance apart 178mm 2 cable entries for through-wiring of mains supply cable ø 7-12mm
Connection terminal 0,5-2,5@
Earth conductor connection
Passive infrared motion sensor (PIR)
Range up to 10m
Horizontal opening angle 110°
Vertical opening angle 93°
Minimum temperature difference between moving object and environment 4 °C
Object speed ideally 1m/s
Adjustable sensitivity of the motion sensor (inertia)
Shut-down delay adjustable between 5s and 240min
Light sensor: adjustable value range from darkness to approaching dusk (approx. 150lx)
Fixed pre-set time hysteresis for suppression of undesired switching operations in luminaires during rapid brightness fluctuations
Luminaire dimmable (0 to 100%)
Adjustable basic brightness
Luminaire can be switched on and off with a non-adjustable soft start function (1s) or directly to the set brightness value
Transmission frequency range: 2400-2483.5MHz
Maximum transmission output: 10mW
LED power supply unit 220-240 V x 0/50-60 Hz
DC 176-264 V
DC Start ≥ 198 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK05
Protection against mechanical impacts < 0.7 joule
Conformity mark
Weight: 1.6 kg

Range / Detection area
The specifications for the range and detection area of the PIR motion sensor are reference values. The detection area is up to 110° horizontally and 93° vertically, with a depth of max. 10m depending on the direction of motion (see sketch). Too minor temperature difference between the moving object and the ambient temperature can influence the detection range. Local conditions and external heat sources may affect both the range and the detection area.
Dimension

Installation

Undo hexagon socket head screw (wrench size 3mm) through the opening in the luminaire housing up to the stop and lift luminaire top. Disconnect the earth conductor connection from the plug connection. Disconnect plug-connection of the LED connecting cable.

Orientation of the sensor
The sensor is factory-configured for the maximum detection area. In order to avoid the unintentional adjustment of the sensor in public areas, the alteration of the factory setting must be made before the luminaire base is mounted. To do so, loosen the two rear screws (Torx driver T10) slightly and rotate the sensor ball to the desired position (see Fig. A). Tighten the mounting screws evenly
Installation

Lead the mains supply cable through the cable entry of the luminaire base. Notice position of use “arrow down” of the luminaire back plate. Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface. Make the earth conductor connection and the electrical connection.

In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire. Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.

Make sure that gasket is positioned correctly. Connect the LED connection cable by means of a plug connector. Make earth conductor connection between luminaire top and luminaire base. Push plug into coupler as far as it will go. Install luminaire top and tighten.

EU Declaration of Conformity
BEGA Gantenbrink-Leuchten KG hereby declares that the radio system type 24 149 complies with Directive 2014/53/EU (RED). The complete text of the EU Declaration of Conformity is available at the following Internet address: https://www.bega.com/conf/de/24149

Commissioning
The power supply must be connected for the commissioning of the luminaire. The brightness sensor will need up to 10 minutes after activation of the power supply to correctly calibrate the brightness value. Once installed, the luminaire can be operated immediately in its factory settings; configuration via smartphone will not be required. The factory settings as are follows: Mode: PIR and light PIR sensitivity: 100 % (high sensitivity) Shut-down delay: 5 minutes Brightness threshold: 40 (approx. 50lx) Dimming level luminaire: 100 % Basic brightness: 20 % Softstart (1s): active Alternatively, the integrated PIR motion and light sensor can be configured via smartphone using the free BEGA Tool app. The default values can be reinstated at any time via the BEGA Tool app.

bega.com/bega-tool-ios

bega.com/bega-tool-android

Download the app for Android or iOS. Create a project and add the luminaire as your starting point. The individual QR code required for commissioning is enclosed with the luminaire. Please retain the other enclosed QR codes in your on-site documentation (e.g. Instructions for use at top of Page 1). You will also find an additional QR code on the LED module in the luminaire.

The luminaire can only be controlled with the smartphone that was used to configure the sensor. The “Share access” function in the BEGA Tool app grants other smartphones configuration and control rights. The luminaire can be reset to factory settings in the app, if required. Follow the in-app instructions.

Please note:
The integrated light sensor operates with a time delay to prevent responses to short-term brightness fluctuations in the environment of the luminaire. The time delay is around 1 to 3 minutes. A manual darkening of the sensor will therefore not result in an immediate response.

Once commissioned successfully, you can choose between three operating modes and one manual control mode.

Operating modes:

PIR motion and light sensor
PIR motion sensor only
Light sensor only

Manual switching:

Sensor deactivation and manual control of the luminaire (on/off

Reset to factory settings
The luminaire must be switched off five times within 30 seconds for at least 2 seconds each time to manually reset it to factory settings (see sketch). The luminaire can furthermore be reset to the factory settings via the BEGA Tool app. The reset is confirmed with five flashes of the luminaire. The smartphone will be disconnected.
Diagram

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt and deposits. Do not use high pressure cleaners.

Replacing the LED module
The designation of the LED module is noted on a label in the luminaire. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.The module can be replaced by qualified persons using standard tools. Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module. Inspect and, if necessary, replace the luminaire gaskets. Defective glass must be replaced. Close the luminaire.

Please note:
After replacing the LED module, the PIR motionand light sensor of the luminaire must be reconfigured (see section Commissioning). To do so, you must use the QR code enclosed with the replacement module. Please paste the additional enclosed QR codes over the QR codes in documentation provided by the customer.

Spares

Spare glass 11 003 511
LED power supply unit DEV-0261/24V
Control board BT 61 001 895
PIR Light sensor 61 001 916
LED module 3000 K LED-1182/830
LED module 4000 K LED-1182/840
Gasket glass 83 000 557 .1
Gasket housing 83 002 168 B1