BEGA 22633 Ceiling · Wall · Pillar luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 22633 Ceiling · Wall · Pillar luminaire
DIMENSION
Application
Ceiling, wall and pillar luminaire with safety guard. A luminaire made of
aluminium alloy and impact resistant crystal glass with light diffusing
structures.
Product description
- Luminaire made of aluminium alloy
- and stainless steel
- BEGA Unidure® coating technology
- Crystal glass, white inside
- 2 mounting holes ø 5.5 mm
- Distance apart 144 mm
- 2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm
- Connecting terminal and
- earth conductor terminal 2.5@
- Lampholder E 27
- Safety class I
- Protection class IP 65
- Dust-tight and protection against water jets Impact strength IK06
- Protection against mechanical impacts < 1 joule
- Safety mark
- EC– Conformity mark
- Weight: 3.0 kg
Safety
- The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
- The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Lamp
Luminaire with screw base E 27
Lamp output max. 75 W
This product contains light sources of energy efficiency classes E, F
- Supplied lamp
- BEGA LED lamp 13 584
- LED Retrofit 7 W · 805 lm · 3000 K
- Luminaire efficiency: 48%
Additional BEGA LED lamps are available for this luminaire:
-
13 586 LED 7 W · 805 lm · 3000 K
dimmable -
13 588 LED 8 W · 1055 lm · 3000 K
-
13 590 LED 12 W · 1400 lm · 3000 K
-
13 592 LED 12 W · 1400 lm · 3000 K
dimmable
Radio-controlled version (Zigbee 3.0):
-
13 555 LED 9 W · 805 lm · 2700 K
dimmable -
13 556 LED 9 W · 805 lm · 2700 – 6500 K
dimmable · tunable white -
13 557 LED 9.5 W · 805 lm · 2700 – 6500 K
dimmable · tunable white · RGBW
Detailed technical and lighting data for the lamps can be found in the data sheets on our website.
Installation
- Undo screws.
- Remove protective guard and glass with gasket.
- Lead the mains supply cable through the cable entry into the luminaire back housing.
- Fix the luminaire back housing with enclosed or any other suitable fixing material onto the mounting surface.
- It is absolutely essential to use the enclosed gaskets.
- Make earth conductor connection.
- Push silicone sleeves over the lines and make electrical connection.
- Insert lamp.
- Insert glass with gasket and protective guard. Make sure that the gasket is in correct position. Tighten screws evenly.
Relamping · Maintenance
- Disconnect the electrical installation.
- Open the luminaire and clean.
- Use only solvent-free cleaning agents. Change the lamp.
- Check the gasket and replace, if necessary. Close the luminaire.
- For cleaning, do not use high pressure cleaners.
Spares
- Spare glass 11 002 665 11
- LED lamp 3000K 13 584
- Lampholder 63 000 355
- Gasket 83 001 831
CONTACT
- ADDRESS: BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden ·
- EMAIL: info@bega.com
- WEB: www.bega.com