MOZA RACING R3 Racing Wheel and Pedals User Manual

: June 12, 2024
: MOZA RACING

Table of Contents

MOZA RACING R3 Racing Wheel and Pedals
R3 WHEEL BASE
Precautions
Specs
FCC Warning
ES Steering Wheel
SR-P Lite Racing Pedals
Packing List
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MOZA RACING R3 Racing Wheel and Pedals

R3 WHEEL BASE

Product Introduction

3.9 N·m Peak Torque
intelligent Temperature Control System
Servo Direct Drive System
Ultra-low Static Torque
Lightweight Design
MOZA Pit House Control Center Software
Aviation-grade Aluminum Body
MOZAApp Cloud Control

Connection Ports

MOZA-RACING-R3-Racing-Wheel-and-Pedals-01 Dimension Xbox Console Connection Guide

Connect the SRP Lite pedal set to the PEDAL port on the base.
Plug the power cord into an electrical outlet.
Plug the supplied usb cable into the corresponding ports on base and Xbox.
Turn on the base by pressing the power button located at the rear and then turn on the Xbox console. If the rpm light on the wheel is in flow breathing mode, it indicates that you have successfully connected to Xbox. However, if the rpm light is in flashing mode, it means that you are in PC mode. In this case, press and hold the Xbox and Radio buttons on the steering wheel simultaneously for 3 seconds to switch to Xbox mode.

PC Connection Guide

Attach the base to the rig mount using either 2 or 4 screw holes on the bottom.
Plug in both the power supply and USB cable into their corresponding ports located at the rear of R3 base. Then connect the USB cable to an available port on your PC.
Briefly press down on the power button located at the back of R3 base to switch it on.
Download the latest version of Moza Pit House from the help center on the Moza Racing website (www.mozaracing.com)
For more information and instructional videos, please visit our officlal website at www.mozaracing.com

Desk Clamp Installation Guide
Attach the base to the clamp using the 4 mounting holes located on the underside of the base. Tighten the clamp to the desk securely to prevent any movement during use.
MOZA-RACING-R3-Racing-Wheel-and-Pedals-07

More information and tutorial videos are available on the official website (www.mozaracing.com)

Precautions

Do not expose the equipment to liquids and moisture to avoid fire/electric shock.
Avoid using the equipment in direct sunlight.
For your safety and well-being, please monitor your gaming time and take breaks as needed.
The device is not suitable for children under 6 years old, small accessories may cause a choking hazard!
Children under 13 years old must be accompanied by their parents.
- Do not dismantle the equipment without the manufacturer’s permission, otherwise you will lose your warranty.
The equipment must be connected using the factory-supplied power supply to prevent an electrical hazard.
To ensure safety, repair or replacement of parts should only be carried out by an authorized repair centre.
- The use of non-standard power supplies is prohibited even if the relevant voltage and other data match.
Only use AC power supplied by a standard wall outlet to avoid damage to the product. Exposure of the equipment to heat sources is prohibited.
Unplug the unit from the power cord and disconnect it if it is not to be used for a long period of time.
If you observe any abnormalities, please stop using it immediately and seek assistance from MOZA officials or the authorized center relevant to your concern.
Stay tuned to the MOZA website and public platform for the latest product information.

This product is intended solely for use in simulated driving activities. It is important to distinguish between simulated games and real-life driving to ensure safety on the road.

Software Introduction

The main page allows you to check the working status of your connected devices and adjust settings. Additionally, you can quickly start games from this page.
With both click and go presets to fully customizable advanced tuning, everyone from beginners to pro drivers can easily find that perfect setup.
Customize force feedback in our FFB Effect Equalizer section, to ensure you get exactly the right feel for every condition.
One click updates the MOZA Racing ecosystem, enjoy the latest features with ease.
For more detailed instructions, please visit the MOZA website (www.mozaracing.com) and download the user manual from our help center page.

Bluetooth connection

Download the MOZA RACING App from the App Store and open it. Tap on “Connect to the device” to begin searching for your device.
Once you have found your device, click on “Connect.”
Click on “Enter the car” to access the settings page.
On the setting page, you can configure and adjust the parameters for both the base and steering wheel.

Specs

Supported Platforms: Xbox Series XIS, Xbox One, Windows 10/11
Drive Type: Direct Drive
Max Wheel Rotation: Limitless
Housing Material: Aviation-grade Aluminum Alloy
Housing Color: Black
Peak Torque: 3.9 N·m
Input Voltage: 110V~240V AC ->12V DC
USB Refresh rate: 1 000Hz
APP Function: Supported
Connection Ports: power, USB, dash, pedals, emergency stop, shifter and handbrake
Accessories: user manual and warranty card, power supply, data cable, and tool kit. Fixing
Method: bottom mount with 2/4 holes
Upgradable firmware: supported

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

This device may not cause harmful interference
This device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

FCC RF exposure statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

IC Caution:

Radio Standards Specification RSS-Gen, issue 5
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.

RF exposure statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

ES Steering Wheel

Product Introduction

Aluminum Wheel Rim Racing Level QR System
Aluminum Alloy Shifters
22 Programmable Buttons
RGB Sequential Shift Light Indicator

Xbox Console buttons

Please note that the RPM LEDs are designed to work with games that support the R3 RACING WHEELAND PEDALS. Please visit www.mozaracing.com/ to see a regularly updated list of compatible games at the bottom of the page.
To switch between Xbox mode and PC mode, please follow these steps: Press and hold the 51 and 52 buttons simultaneously for more than 3 seconds to switch between Xbox and PC mode. When the rpm light flashes at high frequency, it means that you have successfully switch to the other mode. When the rpm light is in the flowing breathing mode, it indicates that the steering wheel is in Xbox mode; When the rpm light is in flashing mode, it indicates that the steering wheel is in PC mode.
lt’s important to note that the LSB and RSB buttons on the Xbox console’s steering wheel only function in specific games.
The list of Xbox Series XIS and Xbox One games that are compatible with R3 is located at

QR Use Guide

Align the 6 ball bearings on the wheel QR with the 6 notches on the base QR mount.
Press the quick release onto the base mount. keeping the bearings and notches aligned.
The quick release will automatically lock into place, if it does not remove it, recheck the alignment and try again.
To remove the wheel, squeeze the black quick release part with the MOZA logo towards the wheel with both hands and pull out the wheel at the same time

Steering Wheel Configuration
The ES steering wheel can be set up easily and quickly in the MOZA Pit House software.

Joystick mode : can be set to button and D-pad
RPM indicator switch mode : choice of three modes; in-game rpm, off and constant Indicator modes: there are two modes, mode 1 and mode 2, which are explained in detail, when the mouse is moved over the option.
RPM indicator timing: choose between early, normal, late or custom to fully match in-game RPM timing.
Brightness: adjust the brightness of the RPM/shift LEDs

(For detailed steering wheel settings and functions, please visit the Maza Racing official website)

Specs

Wheel Rim Material: Aluminum Alloy
Shifter Paddle Material: Aluminum Alloy
Size: 280mm
Buttons: 22
High Brightness LEDs: 10 Pcs
Intelligent Telemetry: Supported
RPM LEDs Fully Adjustable through
MOZA Pit House: Supported Release Method: Quick Release

SR-P Lite Racing Pedals

Product Introduction

High Strength Steel
High Precision Hall Sensors
A Wide Range of Use Scenarios
Detachable
Adjustable Pedal Output Curve

Pedal Installation Guide

Mount the pedal on the footrest and adjust the mounting holes, fix the M4*10 screws to the footrest using a 2.5mm hexagonal spanner. To ensure stability in use, it is recommended that all 4 screws of each pedal are fitted in place.
Connect the connecting cable to the corresponding mounting connector, you can use the cable clip under the pedal base to keep cabling tidy.
To connect the steering wheel to the pedal, please follow these steps: connect one end of the RJ45 cable to the Wheel Base port and the other end to the Pedal port on the base.
The working status of the pedal can be seen in the MOZA Pit House. (If the unit is still grey or does not respond when pressed, unplug the base, close MOZA Pit House, reconnect the base and open Moza Pit House)
The start, end and travel of the pedal can be set in the MOZA Pit House.

Pedal Spacing Adjustment Instructions
Move the pedal left and right to adjust the distance between the pedal and the base holes, align the holes and tighten the screws, (the same for the throttle, brake and clutch) MOZA-RACING-R3-Racing-Wheel-and-
Pedals-16

Instructions for Adjusting the Height of the Pedal Plate

Use a 2.5mm hexagonal spanner to turn the screws on the face of the pedal plate counter clockwise and use a 7mm open-end spanner to remove the back nut from the
the plate screws, move the plate up and down to adjust the plate height according to your needs, then tighten the nuts and screws until they fit the plate and fix it (the plate is adjusted in the same way for the throttle, brake and clutch) MOZA-RACING-R3-Racing-Wheel-and-
Pedals-17