BEGA 33328 Wall and Pedestal Light LE Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
**BEGA 33328 Wall and Pedestal Light LE Instruction Manual
**
Instructions for use
Application
Shielded ceiling, wall and pillar luminaire with high protection class. A luminaire made of aluminium alloy and impact resistant crystal glass with light diffusing structures.
Lamp
Module connected : wattage 3.8 W
Luminaire connected : wattage 4.9 W
Rated temperature : ta=25 °C
Ambient temperature: ta max=55 °C
33 328K3
Module designation: LED-0263/830
Colour temperature : 3000 K
Colour rendering index : CRI >80
Module luminous flux : 755 lm
Luminaire luminous flux : 409 lm
Luminaire luminous efficiency : 83,5 lm/W
33 328K4
Module designation : LED-0263/840
Colour temperature : 4000 K
Colour rendering index : CRI >80
Module luminous flux : 780 lm
Luminaire luminous flux : 423 lm
Luminaire luminous efficiency : 86,3 lm/W
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Product description
Luminaire made of aluminium alloy, aluminium and stainless steel BEGA Unidure®
coating technology Crystal glass, white inside 2 mounting holes ø 5.5mm
Distance apart 144mm
2 cable entries for through-wiring of mains
supply cable ø 7-10.5mm
Connection terminal 2.5@
Earth conductor connection
BEGA Ultimate Driver®
LED power supply unit 220-240 V x 0/50-60 Hz
DC 176-264 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK08
Protection against mechanical impacts < 5 joule
10 – Safety mark
– Conformity mark
Weight: 2.8 kg
This product contains light sources of energy efficiency classes C
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components.
You can find them on our website at www.bega.com.
Installation
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo screws.
Remove frame and glass with gasket.
Lead the mains supply cable through the cable entry of the luminaire base.
Fix luminaire base with enclosed or any other suitable fixing material onto
the mounting surface.
Be sure to use the gasket rings supplied.
Make the earth conductor connection and the electrical connection.
Insert glass with gasket and frame. Make sure that the gasket is positioned
correctly. Tighten screws evenly
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Spares
Spare glass : 11 002 814 11
LED power supply unit : DEV-0303/350
LED module : 3000 K LED-0263/830
LED module : 4000 K LED-0263/840
Gasket glass : 83 001 831
BEGA Gantenbrink – Leuchten KG · Postfach 3160 · 58689 Menden ·
info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>