B E G 93460 LUXOMAT PD4N-M-DACO Dali-2 Instruction Manual

June 12, 2024
B E G

B E G 93460 LUXOMAT PD4N-M-DACO Dali-2 Instruction Manual
B E G 93460 LUXOMAT PD4N-M-DACO Dali-2

Safety instructions

Work on the mains supply may only be carried out by qualified professionals or by instructed persons under the direction and supervision of qualified skilled electrical personnel in accordance with electrotechnical regulations

Disconnect supply before installing! This device is not to be used to isolate other equipment from the mains supply.

DALI is not SELV – the installation instructions for low voltage apply. The DALI screw clamps must not be connected to 230VAC!

After inserting the connection cables, plug on the supplied cover.

Note Icon
Read this supplementary sheet and the operating instructions before putting the device into operation. Knowledge of these documents is part of the intended use!

Oeration

Note Icon
Occupancy detector with integrated DALI application controller for energy- efficient lighting control. DALI-2 certified product. Integrated DALI power supply. DALI interface for controlling digital, dimmable ECGs in broadcast mode. Manual switching or dimming via conventional pushbuttons. Bidirectional IR communication enables fast integration into the project management function of the B.E.G. One app.

Complete range of functions can only be activated using the BLEIR-Adapter and a compatible Smartphone or Tablet (Android, iOS). Factory setting 10 min follow-up time and 500 lux brightness set value. Single master version, not networkable. Detection area can be extended with slave devices.

Number of DALI participants can be determined quickly and reliably via the B.E.G. Online DALI Line Planner. For a reliable calculation, it is recommended to always use 80% of the guaranteed output current as a basis.

Mounting

Range of coverage/Product Code

| 1| 2| 3
---|---|---|---
2.50m| Ø 24.00m| Ø 8.00m| Ø 6.40m
5.00m| Ø 48.00m| Ø 16.00m| –

Mounting hints

Overview

Fig. 1a : Device is inserted into false ceiling

Fig. 1b: The device is attached to a flush-mounted box
Mounting Hints

Fig. 1c : Device is mounted on SM adapter
Mounting Hints

When replacing the cover, please take care that the opening for light sensor 1 is placed on the same

Fig. 2: Blinds (e) are clipped to restrict detection area.

Product Overawe

Fig. 3 : Light sensor 1 for point light measurement, light sensor 2 for ambient light measurement.

Product Overawe

Exclude sources of interference

In case the detection area of the detector is too large or areas are being covered that should not be monitored, the range can be reduced or limited by using the enclosed blinds.

LED function indicators

Process Indication
Initialization time Red flashes for 60s
Load factory settings Running light for 30s, then: Red flashes for 30s
Read out device (send IR) Red flickers
Motion detection Red flashes for each detected motion
Brightness set value exceeded Green flashes 2x per 1s
Light calibration active Green flashes every 10s
Semi-automatic mode active White lights up permanently
Corridor mode active White flashes every 3s
Error detected ( device or bus) Red/green/ white flash simultaneously

Accessory

93067 BLE-IR-Adapter
92094 IR-PD-DALI
92652 IR-PD-DALI-LD
92122 IR-PD-DALI-E
92112 IR-PD-DALI-Mini
92199 Wire basket BSK / white
93465* SM socle mounting set IP54 PD4N H / white
93732* Iens PD4N, Cover ring / traffic white
93073* Corridor lens PD4N type A / white
93164* Wall holder PD2N/4N Typ A / white
93192* SM socket for Wall holder / white

Technical date

230 V AC ±10% 50 Hz Voltage
Ø 106 x 95 mm Dimensions
ca. 2 W Power consumption
max. 8 Slave devices
horizontal 360° Detection area
30 m x 19 m Reichweite bei
  1. quer
  2. frontal
  3. sitzende Tätigkeit

450 m² / 2,5 m| Monitored area (tangential movement)
2 m / 10 m / 2,5 m| Mounting height min./max./ recommended
| Terminal clamps: for solid one-wire conductors
IP20 / II| Degree/Class of protecti
25°C – +50 °C| Ambient temperature
PC| Housing material

Channel 1 (lighting control)

80mA max. 125mA DALI output
DT0, DT5, DT6, DT7 Supported control gear
– (Single Master) Supported control devices
1 min – 150 min Follow-up time
10 – 30 % / 1 – 60 min / ∞ / OFF Orientation light
10 – 2500 Lux Brightness set value
Mixed light measuring

Factory settings
10 min| Follow-up time
500 Lux| Brightness set value

Wiring diagram

Wiring diagram

EU Declaration of conformity

This product respects the directives concerning

  1. Electrical Equipment Safety Regulation 2016
  2. Electromagnetic Compatibility Regulation 2016
  3. The Restriction of the Use of Certain Hazardous Substances

in Electrical and Electronic Equipment Regulation 2012

Contact

  • B.E.G. UK Ltd., Apex Court –
  • Grove House • Camphill Road •
  • West Byfleet, Surrey KT14 6SQ

Product page on the internet

LUXOMAT® PD4N-M-DACO DALI-2 93460

Documents / Resources

| B E G 93460 LUXOMAT PD4N-M-DACO Dali-2 [pdf] Instruction Manual
93460, 93460 LUXOMAT PD4N-M-DACO Dali-2, 93460 Dali-2, LUXOMAT PD4N-M-DACO Dali-2, PD4N-M-DACO Dali-2, LUXOMAT Dali-2, Dali-2
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals