BOX DESIGN RS2 Pro-Ject Power Box Phono Instruction Manual
- June 3, 2024
- BOX DESIGN
Table of Contents
RS2 Pro-Ject Power Box Phono
Instruction Manual
INSTRUCTIONS FOR USE
Pro-Ject Power Box RS2 Phono
RS2 Pro-Ject Power Box Phono
Dear music lover, Thank you for purchasing a Pro-Ject Audio Systems Power Box
RS2 Phono. In order to achieve maximum performance and reliability you should
study these instructions for use carefully.
Warning of a hazard for the user, the unit or possible misuse
Important notice
Safety Instructions
AC outlet voltages vary from country to country. Before connecting to the
mains, make sure that the voltage in your area meets the voltage requirements
printed on the power supply. Never handle the device while your hands are wet
or damp.
Avoid letting liquids enter the device. Never place any item containing
liquid, such as a flower vase on or near the device. Never spill any liquid on
the device. Never place any naked flame sources, such as lighted candles on or
near the device. The product shall not be used in damp or wet locations, next
to a bathtub, sink, swimming pool or any other similar conditions.
Using the product
Power Box RS2 Phono is designed to power a wide range of DC-powered Pro-Ject
turntables with 15V and phono preamplifiers with 18V or 20V.
Make all connections whilst the Power Box RS2 Phono is switched off or
disconnected from the mains.
Interconnection cables are included in the packaging. Original power supplies
are no longer required. Ensure that you use the correct cable for your device:
The cables are marked on both ends. In case of any doubts, consult the user
manuals of all connected products or ask your dealer.
Make sure that the Input AC selector matches the mains voltage in your country
Main power switch
The toggle switch on the front panel turns the unit on or off. The blue LED
above the switch shows that the unit is switched on.
Led indicators
The LEDs Turntable and Phono Stage on the front indicate that a device is
connected.
All Pro-Ject Phono Boxes with 18V or 20V can be powered with the Phono Stage
Output.
Technical specifications Pro-Ject Power Box RS2 Phono
Input Power supply:……. 115V/230V AC
Output voltage/current/ripple ………………1 x 15V ±0,5% / 2A / max. 35mV pp
Output voltage/current/ripple …………………1 x ±18V ± 0,5% / 2A / max. 50mV pp
Dimension (W x D x H):……………….. 206 x 209 x 71
Weight:…………………………….. 2930 g
Service
Should you encounter a problem that you are not able to alleviate or identify despite the above information, please contact your dealer for further advice. Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use. Modification or change to any part of the product by unauthorized persons, releases the manufacturer from any liability over and above the lawful rights of the customer.
Copyright, trademarks
Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems Copyright © 2022. All
rights reserved.
The information was correct at the time of going to press. The manufacturer
reserves the right to make changes to the technical specification without
prior notice as deemed necessary to uphold the ongoing process of technical
development.
Declaration of Conformity
We, Canor spol. s r.o.
Druzstevná 13925/39 08006
Presov Slovakia (manufacturer)
Pro-Ject Audio Systems a division of Audio Tuning GmbH
Margaretenstrasse 98
1050 Vienna, Austria (distributor)
declare under our responsibility that the product is in conformity with the
provisions of Directives:
2014/35/EU including amendments
2014/30/EU including amendments
STN EN 62368-1:2015 – Safety
STN EN 55035:2018 – Electromagnetic compatibility of multimedia equipment –
Immunity requirements
STN EN 55032:2015 – Electromagnetic compatibility of multimedia equipment
Emission requirements
3 © Pro-Ject Audio Systems
Pro-Ject Power Box RS2 Phono
Revision 2022.01.03