BEGA 31 053 Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

31 053 Wall Luminaire
Application
Product description
Safety
Overvoltage protection
Lamp
Installation
Cleaning · Maintenance
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

31 053 Wall Luminaire
Instruction Manual 06.22
Technical amendments reserved
31 053
IP 65

31 053 Wall Luminaire

Wall luminaire BEGA 31 053 Wall Luminaire - fig Instructions for use

Application

Upwardly shielded cast aluminium wall luminaire.
Luminaire with hand-blown, three-ply opal glass for a wide range of lighting applications.

Product description

Luminaire made of aluminium alloy, aluminium and stainless steel BEGA Unidure® coating technology
Opal glass
Silicone gasket 2 mounting holes ø 5.5 mm
Distance apart 190 mm 2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm
Connecting terminal 2.5@with plug connection
Earth conductor connection
LED power supply unit 220-240 V x 0/50-60 Hz
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK05
Protection against mechanical impacts < 0.7 joule
– Safety mark
****– Conformity mark
Weight: 2.3 kg
This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

Module connected wattage	7.8 W
Luminaire connected wattage	9 W
Rated temperature	ta = 25 °C
Ambient temperature	ta max = 55 °C

31 053 K3

Module designation	LED-0916/830
Colour temperature	3000 K
Colour rendering index	CRI > 80
Module luminous flux	1450 lm
Luminaire luminous flux	815 lm
Luminaire luminous efficiency	90,6 lm / W

Installation

Lead the mains supply cable through the cable entry of the luminaire base.
Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Make the earth conductor connection and the electrical connection.
In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.
Push plug into coupler as far as it will go.
Make sure that gasket is positioned correctly.
Place the opal glass with LED unit onto the luminaire base in such a way that both yellow arrow markers align to each other and screw the glass clockwise into the base up to the stop.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.