VIDEX VLF-H065A 1200 MAX Lumens Headlamp User Manual
- June 12, 2024
- VIDEX
Table of Contents
- VIDEX VLF-H065A 1200 MAX Lumens Headlamp
- Product Information
- Product Usage Instructions
- TECHNICAL PARAMETERS
- PRODUCT OVERVIEW
- TECHNICAL PARAMETERS
- MAIN FEATURES
- INCLUDED
- LIGHTING MODES
- OPERATING INSTRUCTION
- BATTERY STATUS INDICATION
- CHARGING
- BATTERY REPLACEMENT
- MAINTENANCE AND SAFETY INSTRUCTIONS
- WARRANTY
- ENVIRONMENTAL PROTECTION
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
VIDEX VLF-H065A 1200 MAX Lumens Headlamp
Product Information
Parameter | Value |
---|---|
Model | VLF-H065A |
Maximum Brightness | 1200 lumens |
Water Resistance | IP68 (short-term immersion under water to a depth of 2 |
meters)
Battery Type| Li-ion 18650 2200mAh
Charging Type| Type-C, 5V 1A
Runtime| Refer to the user manual for detailed runtime information
Distance| Refer to the user manual for detailed distance information
Intensity| Refer to the user manual for detailed intensity
information
Product Usage Instructions
- Press the mode switch button to cycle through different lighting modes: Turbo, High, Middle, Low, Moon, and SOS.
- To check the battery charge, with the light switched off, shortly press the button. The battery status will be displayed for 3 seconds.
- Continuous green light: 100-80% charge
- Flashing green light: 79-50% charge
- Continuous red light: 49-25% charge
- Flashing red light: critical charge 24-1%
- To replace the battery:
- Unscrew the battery cover counterclockwise.
- Insert the battery according to the diagram shown on the outside of the headlamp’s body.
- Screw the battery cover all the way in and test the device.
Note: For more detailed information on runtime, distance, intensity, and charging time, refer to the user manual. The mentioned parameters may vary between environments and actual batteries used.
The warranty for the headlamp is 3 years, and for the battery is 1 year.
Pursuant to the provisions of the WEEE Act, it is forbidden to put waste
equipment marked with the symbol of a crossed bin together with other waste.
The user, wishing to get rid of electronic and electrical equipment, is
obliged to return it to a waste equipment collection point. There are no
hazardous components in the equipment that have a particularly negative impact
on the environment and human health. The producer shall not be responsible for
any damage resulting from the failure to follow the above
instructions. The producer reserves the right to make updates to this user’s
manual.
TECHNICAL PARAMETERS
PRODUCT OVERVIEW
Producer/Producent: Allegro Opt Sp. z o.o., Handlowa 23, 05-120 Legionowo, Poland. Made in P.R.C.
TECHNICAL PARAMETERS
- Output.
- Runtime.
- Distance.
- Intensity.
- Correlated color temperature.
- LED type.
- Compatible battery.
- Charging port type, voltage and current.
- Charging time.
- Dust and moisture protection level.
- Impact resistance.
- Product sizes.
- Product weight (without battery).
- Color: black.
- Optical system type: optical lens
- Materials: Aviation anodized aluminum, tempered glass.
Note: Runtime, Distance, Intensity and Charging time results tested with a
stock battery Videx 18650 2200mAh. The above mentioned parameters may vary
between environments and actual batteries used.
*The Turbo mode runtime is the accumulated time, including reduced output levels with the overheat protection enabled.
MAIN FEATURES
- Maximum brightness 1200 lumens in a compact body;
- Frosted optical lens for optimal balance between low and high beabeam;
- Water resistance IP68 (short-term immersion under water to a depth of 2 meters);
- Side magnet for various secondary mounting ways;
- Both fast release holder and standard holder included; Compatible with primary 2xCR123A batteries.
INCLUDED
- Headlamp VLF- H065A;
- Li-ion battery Videx 18650 2200mAh;
- Charging cable;
- Headband;
- Quick release holder;
- Standard holder;
- Spare O-rings; 8. User’s manual.
LIGHTING MODES
- Turbo – maximum brightness
- High – high brightness
- Middle – medium brightness
- Low – low brightness
- Moon – minimum brightness
- SOS – emergency signal
OPERATING INSTRUCTION
- ON/OFF – press and hold the button for 0.5 seconds to turn on/off the light;
- Modes selection – when the light is switched on, shortly press the button to switch between modes cyclically.
- SOS mode – press and hold the button for 3 seconds. Short press again to exit SOS mode.
- Lock/Unlock – with the light switched off , double press the button continuously within 0.5 seconds to lock the fl ashlight. The fl ash light will respond by appropriate double fl icker. Double press again to unlock.
The headlamp automatically memorizes the last selected lighting mode (except the SOS mode) and applies it next time when turned on.
BATTERY STATUS INDICATION
With the light switched off , shortly press the button to see the battery status. The indication will last for 3 seconds. The battery status is also continuously displayed when the light is turned on.
- Continuous green light – 100-80% charge;
- Flashing green light – 79-50% charge;
- Continuous red light – 49-25% charge;
- Flashing red light – critical charge 24-1%.
CHARGING
Plug the USB-A socket of the charging cable into electrical outlet. Switch off
the light, unscrew the protective cover counterclockwise and connect the
charging cable to the headlamp port.
ATTENTION: primary CR123A batteries cannot be charged.When charging, the
indicator glows red. When fully charged, the indicator glows green.
After a full charge, unplug the charging cable and screw the protective cover
all the way in to prevent water and dust from entering the headlamp body.
© The original rechargeable batteries are supplied charged and can be used
immediately after purchase, however it is recommended that the battery be
fully charged before fi rst use. The battery needs to be charged in time before
it is completely discharged. During long periods of storage, it is recommended
to keep the battery charging level at about half capacity to extend its
service life.
BATTERY REPLACEMENT
- a) Unscrew the battery cover counterclockwise;
- b) Insert the battery according to the diagram shown on the outside of the headlamps body;
- c) Screw the battery cover all the way in and test the device.
MAINTENANCE AND SAFETY INSTRUCTIONS
- For long-term storage, it is necessary to remove the batteries from the device.
- It is recommended to regularly lubricate the rubber seals and threaded parts of the headlamp to prevent premature wear and ensure the waterproof housing. If the rubber rings are damaged, they must be replaced.
- Lock the headlamp to avoid accidental activation during carrying and storage;
- ATTENTION. Avoid direct light into eyes as it may cause the eyes damage.
- The headlamp can accumulate a signifi cant amount of heat when used for a long time, which can cause the body to become hot. Therefore, be careful to avoid burns.
- t is forbidden to shine the headlamp in a critical proximity to easily fl ammable substances in order to avoid fi re.
- Do not use batteries other than those specifi ed in the technical specifi cations.
- Do not disassemble the headlamp head as this may compromise performance and void the warranty.
- Do not charge the headlamp with CR123A batteries inside.
- Keep out of the reach of children.
WARRANTY
The warranty for the headlamp is 3 years, for the battery – 1 year.
The warranty does not cover accessories. The LED source inside the headlamp is
not replaceable. If the LED fails, the whole headlamp should be replaced.
During the warranty period, a faulty headlamp and battery can exchanged or
returned with the prove of purchase and all accessories saved.
The following does not apply with the scope of limited warranty:
-
Misuse the product and cause the products integral components damage;
Unauthorized disassemble or the presence of deep mechanical damage to the product; -
Damage due to force majeure.
ENVIRONMENTAL PROTECTION
Pursuant to the provisions of the WEEE Act, it is forbidden to put waste
equipment marked with the symbol of a crossed bin together with other waste.
The user, wishing to get rid of electronic and electrical equipment, is
obliged to return it to a waste equipment collection point. There are no
hazardous components in the equipment that have a particularly negative impact
on the environment and human health.
The producer shall not be responsible for any damage resulting from the
failure to follow above instructions. The producer reserves the right to make
updates of this user’s manual.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>