SCHNEIDER EVlink EV Series EV Charger User Manual

SCHNEIDER EVlink EV Series EV Charger

Specifications

• Model Numbers: EVH4S03N2, EVH4S07N2, EVH4S11N2, EVH4A03N2, EVH4A07N2, EVH4A11N2
• Customer Care Center Models: EVH4S03NC, EVH4S07NC, EVH4S11NC, EVH4A03NC, EVH4A07NC, EVH4A11NC
• Power Cable Requirements: Included in the Protection section

Product Description
The EVlink Home series includes both standard and smart models designed for electric vehicle charging. The product line offers various configurations to suit different charging needs.

Product Characteristics
The EVlink Home chargers are known for their reliability, efficiency, and user-friendly features. They are designed to provide safe and convenient charging for electric vehicles.

Protection

• Upstream Protections: The charger is equipped with built-in protections to ensure safe charging operations.

• Power Cable Requirements: Refer to the user manual for specific power cable requirements based on the model.

• Wiring
  Proper wiring is essential for the correct functioning of the charger. Follow the wiring instructions provided in the user manual to ensure a safe and reliable connection.

• Connection
  Make sure to follow the recommended connection procedures outlined in the user manual. Proper installation of the charger is crucial for efficient charging and long-term performance.

• Installation

  • Mark Installation Area: Select a suitable location for installing the charger, ensuring proper ventilation and accessibility.
  • Drill, Fix and Mount: Follow the installation instructions carefully to securely mount the charger in the chosen location.

• Operation
  After completing the installation and connection of the charger, refer to the user manual for detailed operating instructions. The charger is designed to be user-friendly for everyday use.

FAQ

• Can I install the charger myself?
  It is recommended to have a qualified electrician install the charger to ensure proper setup and safety.

• What should I do if the charger malfunctions?
  If you encounter any issues with the charger, refer to the troubleshooting section of the user manual or contact the Customer Care Center for assistance.

EVlink Home – EVH4SpppNp EVlink Home Smart- EVH4ApppNp
User manual

• The Schneider Electric brand and any trademarks of Schneider Electric SE and its subsidiaries referred to in this guide are the property of Schneider Electric SE or its subsidiaries. All other brands may be trademarks of their respective owners.
• This guide and its content are protected under applicable copyright laws and furnished for informational use only. No part of this guide may be reproduced or transmitted in any form or by any means electronic, mechanical, photocopying, recording, or otherwise), for any purpose, without the prior written permission of Schneider Electric.
• Schneider Electric does not grant any right or license for commercial use of the guide or its content, except for a non exclusive and personal license to consult it on an «as is» Schneider Electric products and equipment should be installed, operated, serviced, and maintained only by qualified personnel.
• As standards, specifications, and designs change from time to time, information contained in this guide may be subject to change without notice.
• To the extent permitted by applicable law, no responsibility or liability is assumed by Schneider Electric and its subsidiaries for any errors or omissions in the informational content of this material or consequences arising out of or resulting from the use of the information contained herein.

Safety

Important Information

• Read these instructions carefully, and look at the equipment to become familiar with the device before trying to install, operate, or maintain it. The following special messages may appear throughout this documentation or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.

• The addition of this symbol to a “Danger” or «Warning» safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed.

• This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

• DANGER
  DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

• CAUTION
  CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE

• NOTICE is used to address practices not related to physical injury.

PLEASE NOTE

• The installation, maintenance and eventual replacement of this device must only be carried out by a qualified electrician.

• This device must not be repaired.
  All applicable local, regional and national regulations must be complied with during the installation, use, maintenance and replacement of this device.

• This device should not be installed if, when unpacking it, you observe that it is damaged.

• Schneider Electric cannot be held responsible in the event of non-compliance with the instructions in this document and in the documents to which it refers. b The service instruction must be

• observed throughout the life time of this device.

• The equipment must be installed, commissioned, serviced, and maintained only by qualified personnel.
• The installation should comply with existing standards and local regulations.
• See section “Installation” page 13 for details.

Electrical hazard / fire hazard

• The charging station, the cable and the connector must be regularly checked by to detect any potential damage (visual inspection).
• In case the charging station is damaged, it must be immediately turned off and replaced.
• Do not perform any maintenance work on the equipment.
• Do not open or modify the charging station.
• Do not remove signs such as safety symbols, warnings, nameplates, signs or markings.
• Do not use any extension cable to connect the charging station to the electric vehicle.
• Do not connect any other type of loads to the charging station (power tools, etc.). Only connect electric vehicles or their charging equipment. b Do not disconnect the connector by pulling the cable. Hold the connector in your hand to disconnect the connector from the electrical vehicle. b Do not bend, squeeze or tilt the connector so that it is mechanically damaged.
• Prevent the connector to be in contact with heat source, dirt or water.
• When using an integrated charging station to charge your electric car, please read the vehicle’s tips and instructions carefully.
• Failure to follow safety instructions can result in death, injury, and equipment damage.

| Never clean the charging point by spraying it with water (Hose for garden watering, high pressure cleaners, etc)

Contents

Description

Product References

Reference| Short Description| Power supply| Power rating| Electrical protection
---|---|---|---|---
EVH4S03N2| EVlink Home 1P T2 3.7 kW 16A – with RDC-DD| T2 socket| 3.7 kW 16A| with 6 mA RDC-DD filter
EVH4S07N2| EVlink Home 1P T2 7.4 Kw 32A – with RDC-DD| T2 socket| 7.4 kW 32A| with 6 mA RDC-DD filter
EVH4S11N2| EVlink Home 3P T2 11 kW 16A – with RDC-DD| T2 socket| 11 kW 16A| with 6 mA RDC-DD filter
EVH4S03NC| EVlink Home 1P attached cable 5 m 3.7 kW 16A – with RDC-DD| Attached cable 5 m / 16.4ft| 3.7 kW 16A| with 6 mA RDC-DD filter
EVH4S07NC| EVlink Home 1P attached cable 5 m 7.4 Kw 32A – with RDC-DD| Attached cable 5 m / 16.4ft| 7.4 kW 32A| with 6 mA RDC-DD filter
EVH4S11NC| EVlink Home 3P attached cable 5 m 11 kW 16A – with RDC-DD| Attached cable 5 m / 16.4ft| 11 kW 16A| with 6 mA RDC-DD filter
EVH4A03N2| EVlink Home Smart 1P T2 3.7 kW 16A – with RDC-DD| T2 socket| 3.7 kW 16A| with 6 mA RDC-DD filter
EVH4A07N2| EVlink Home Smart 1P T2 7.4 Kw 32A – with RDC-DD| T2 socket| 7.4 kW 32A| with 6 mA RDC-DD filter
EVH4A11N2| EVlink Home Smart 3P T2 11 kW 16A – with RDC-DD| T2 socket| 11 kW 16A| with 6 mA RDC-DD filter
EVH4A03NC| EVlink Home Smart 1P attached cable 5m 3.7 kW 16A – with RDC-DD| Attached cable 5 m / 16.4ft| 3.7 kW 16A| with 6 mA RDC-DD filter
EVH4A07NC| EVlink Home Smart 1P attached cable 5m 7.4 Kw 32A – with RDC-DD| Attached cable 5 m / 16.4ft| 7.4 kW 32A| with 6 mA RDC-DD filter
EVH4A11NC| EVlink Home Smart 3P attached cable 5m 11 kW 16A – with RDC-DD| Attached cable 5 m / 16.4ft| 11 kW 16A| with 6 mA RDC-DD filter

Dimensions and Weight

Model| EVH4S03N2 EVH4S07N2 (charging station with T2 socket: socket, type T2) EVH4S03NC,EVH4S07NC (charging station with charging cable: cable, type T2) EVH4A03N2,EVH4A07N2 (Smart charging station with T2 socket: socket, type T2)

EVH4A03NC,EVH4A07NC (Smart charging station with charging cable: cable,

type T2)

| EVH4S11N2 (charging station with T2 socket: socket, type T2) EVH4S11NC (charging station with charging cable: cable, type T2) EVH4A11N2 (Smart charging station with T2 socket: socket, type T2) EVH4A11NC (Smart charging station with charging cable: cable, type T2)
---|---|---
Power rating| 3.7 and 7.4 kW| 11 kW
Dimensions| 282 mm × 409 mm × 148 mm / 11.1 in x 16.1 in x 5.83 in
Weight| T2 socket: approx. 3.7 kg / 8.15 lb. Attached cable: approx. 5.2 kg / 11.46 lb
Installation| Wall-mounted

Product Description

• This charging station is an electrical appliance that supplies electric energy to charge plug-in electric vehicles for indoor and private outdoor areas.
• When installing and using the charging station, ensure that you comply with local regulations.
• The intended use of the equipment includes, in all cases, the environmental conditions established for the equipment.

A| Cable winding trough| When not in use, wind the charging cable around the charging station’s trough to avoid tripping hazards and equipment damage.
---|---|---
B| Stop button| Only to be used in an emergency. In normal use, stop the charge via the Electric Vehicle. The button can be reset by rotating it 90° clockwise.
C| LED status indicator| Indicate the status of the charging station and charging session, section “Charging Station Status Indicators”, page 18.
D| Charging socket| Plug in your T2 charging cable

A| Cable winding trough| When not in use, wind the charging cable around the charging station’s trough to avoid tripping hazards and equipment damage.
---|---|---
B| Stop button| Only to be used in an emergency. In normal use, stop the charge via the Electric Vehicle. The button can be reset by rotating it 90° clockwise.
C| Connector unlock button| Push the button to unlock the charging connector.
D| LED status indicator| Indicate the status of the charging station and charging session, section “Charging Station Status Indicators”, page 18.
E| Charging connector dock| Dock the charging connector when not in use to avoid tripping hazards and equipment damage.

Characteristics

General Data

• Ingress protection rating: according to IEC 60529
• IP54 for EVlink Home with T2 socket
• IP55 for EVlink Home with attached cable
• Impact protection rating: IK10 (IEC 62262)
• Socket for T2 cable or T2 attached cable according to IEC 62196-1 and IEC 62196-2
• Operating temperature: -30°C to +50°C (-22°F to +122°F)
• Storage temperature: -40°C to +80°C (-40°F to +176°F)
•  Relative humidity: 5-95 %
• Rated voltage (depending on model):
• For 3.7 and 7.4 kW: 220~240V AC, 50 Hz v For 11 kW: 380~415V AC, 50 Hz
• Rated charging current: 16 A for 3.7 kW, 32 A for 7.4 kW and 16 A for 11 kW
• Accuracy of current, voltage and power measurement: 1%
• Diagram of the earthing system:TN-S, TN-C-S, TT, IT (230V)
• Designed for indoor and outdoor use
• OCPP 1.6J (Smart version only)
• Wi-Fi feature 2.4 GHz (Smart version only)
• Operating frequency bands: 2412MHz – 2472MHz
• Maximal RF output power: less than 20 dBm (18.25dBm)
• 1 Ethernet port (Smart version only)
• 1 RS485 port (Smart version only)

Certification

• IEC/EN 61851-1 ed 3.0 b IEC 61851-21 – 2
• IEC 62955-2018
• EN 61000-6-1
• EN 61000-6-3

Environment

• Compliant with the RoHS European directive
• Compliant with the REACH European regulation

Accessories

• EVlink Home Anti-tripping module, single-phase (EVA1HPC1)
• EVlink Home Anti-tripping module, three-phase (EVA1HPC3)

Notes :
The Anti-Tripping Module limits the maximum power draw of the EVlink Home charging station and can completely stop the charge to ensure the continuity of the electrical distribution under all conditions. Refer to Anti-tripping module’s instruction sheet.

Protection

DANGER

• HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
  Do not install automatic reset systems on the residual current protection device. Failure to follow these instructions will result in death or serious injury.

Upstream Protections

• Electric Vehicle measures the earth resistance and will only start charging if it’s lower than the threshold defined by the Electric Vehicle manufacturer. Refer to the vehicle’s technical documentation.
• The choice of electrical protections and wire gauges must comply with local regulations and the information below as well as the constraints of the electrical installation. In particular, the selected protection must not only satisfy the requirements of IEC 61851-1 ed 3.0 but must also limit the value of I²t to less than 75 000 A²s in case of a
  short-circuit.

According to selectivity with upstream protections

• Recommended protection: Acti9 iC60
• A Undervoltage release (MNx) controlled by the charging station must be installed to enable to activate the upstream circuit-breaker tripping. b The protections described below should only be taken as suggestions and Schneider Electric cannot be held liable.
• Recommendations for lightning protection
• One surge arrester per charging station is recommended for high keraunic levels, mandatory if required by local regulations.

Power Cable Requirements

• For wiring section “Wiring”, page 8, please comply with local regulations.
• The maximum wire gauge should not exceed 6 mm² (AWG 9).
• Two types of wire as recommended when connecting the charging station to the power supply:
• To use flexible cables with ring terminal and crimp ring terminals. v To use rigid cable.

1-phase installations

 | Distribution board – EVlink Home and EVlink Home Smart| EVlink Home and EVlink Home Smart – Undervoltage Release (MNx)
---|---|---
Diameter| 3 x 6 mm² (3 x AWG 9) (Type U1000R2V 3G)| 2 x 0.5 mm² (2 x AWG 20)
Length| < 50 meters (164.04 ft)| < 30 meters ( 98.43 ft )
 | Distribution board – EVlink Home and EVlink Home Smart| EVlink Home and EVlink Home Smart – Undervoltage Release (MNx)
---|---|---
Diameter| 5 x 6 mm² (5 x AWG 9) (Type U1000R2V 5G)| 2 x 0.5 mm² ( 2 x AWG 20 )
Length| < 50 meters (164.04 ft)| < 30 meters ( 98.43 ft )

Wiring

TN/TT Earthing System Wiring

IT Earthing System Wiring 230V only

Connection

DANGER

• HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
• Disconnect the mains power supply before working on the charging station.
• Use a Voltage Tester of appropriate rating.
• Do not turn on the charging station if the earth resistance measured is higher than the threshold defined in the enforceable regulations. b Connection to a Undervoltage release (MNx). It is not  supplied with the charging station.
• Do not connect to an lT earthing system if the voltage exceeds 240Vac
• Failure to follow these instructions will result in death or serious injury.

Undervoltage Release (MNx )

• Install a Undervoltage release (MNx) as described in the wiring diagram (section “Wiring”, page 8) to increase operator safety with IEC 61851-1.
•  Connect the Undervoltage release (MNx) with 0.5 mm² (20 AWG) 2-core cable with insulation for 220~240 V no wider than 5 mm.
• Take the rubber gasket and poke out 1 of the 2 rubber plugs.
• Pass the 2 wires connecting the Undervoltage release (MNx) through the now empty plug.
•  Inside the EVlink Home charging station, insert 1 wire from the Undervoltage release (MNx) into the K2 terminal of the connector (insert thin screwdriver into connector’s largest hole and push down to open clamp).
• Insert the other end into the K1 terminal of the connector (insert thin screwdriver into connector’s largest hole and push down to open clamp).

Connection

Wire-up Power Supply
TN/TT Earthing System Wiring

• 1-phase EVlink Charging Station
• 3-phase EVlink Charging Station

IT Earthing System Wiring 230V only

• 1-phase EVlink Charging Station
• 3-phase EVlink Charging Station

Wire-up Power Supply

• Flexible cable with ring terminal connection
• Rigid cable connection
• Flexible cable with ring terminal connection
• Rigid cable connection

Ethernet Port Connection (Optional for EVlink Home Smart Charging Station)

• When installing EVlink Home Smart charging station, consider whether to do ethernet connection in advance.
• If needed, follow below connection guide procedures. Connect ethernet connector into ethernet port.
• Note :
  For EVlink Home Smart, prefer the wired connection by Ethernet cable to the Wi-Fi connection when the charging station is installed outside or when it is not in the same room as your box/router/repeater Wi-Fi.

RS485 Port Connection (Optional for EVlink Home Smart Charging Station)

• When installing EVlink Home Smart charging station, consider whether to do RS485 connection for Certified Power Meter (MID) in advance.
• If needed, follow below connection guide procedures. Connect RS485 wire 1 x 0.5 mm² (1 x 20 AWG) with positive (+) data into A terminal, connect RS485 wire 1 x 0.5 mm² (1 x 20 AWG) with negative (-) data into B terminal. Refer to Energy Meter (MID) instruction sheet, do not reverse the RS485 wire connection.
• Energy Meter (MID) references: A9MEM2155, A9MEM3155.
  • The speed of the meters have to be set at 19200 baud.
  • Other parameters to be used are default parameters. For information: Parity: even, Stop bit: 1, Do not use address 247″.
• Secure Inspection Hatch

Clamp Power Cable

• Select clamp position according to power cable diameter

Installation

DANGER

• HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
• Disconnect power supply before working on this equipment.
• Use a voltage tester of suitable rating.
• Do not start the charging station if the ground resistance measured is greater than the threshold defined by the applicable law.
• Install the over-current and residual current protections as described in the instructions and recommendations chapter (section “Operation”, page 17). b Do not use a system which automatically resets the residual current circuit breaker.
• Failure to follow these instructions will result in death or serious injury.

WARNING

• RISK OF DAMAGING THE CHARGING STATION

• Protect the charging station from dust and water while fixing the bracket.

• Attach the charging station to a flat surface.

• Use screws, washers and wall plugs suitable for the wall material.
  Failure to follow these instructions can result in death, serious injury, or equipment damage.

• Check the installation area before marking it on the wall. It is recommended to situate the top of the charging station between 0.8 to 1.6 m / 2.62 to 5 .25 ft above the ground. ****

• Place the drilling template at a suitable height, and mark the support screws on the wall with a pencil.

• Ensure you allow sufficient space around the charging station to wind the cable and access the stop button (left-hand side).

WARNING

• HAZARD OF ELECTRIC SHOCK
• Disconnect power supply.
• Failure to follow these instructions can result in death, serious injury, or equipment damage.

Recommended installation procedure

1. Read EVlink Home’s Instruction Sheet
2. Mark area using Installation Template sheet
3. Drill holes through template
4. Fix screws and bracket to holes
5. Wire upstream protection (section “Protection”, page 7)
6. Wire shunt trip release (MNx) to charging station
7.  Wire power supply to charging station
8. Secure charging station’s inspection hatch
9. Clamp charging station’s power cable
10. Mount charging station onto screws and bracket
11. Fix bracket to charging station
12. Install anti-tripping system (optional)
13. Inspect installation (section “Inspection”, page 14)
14. Check stop button unlocked (section “Configuration”, page 15)
15. Reconnect power supply

Drill, Fix and Mount

Inspection

DANGER

• HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
  Wear suitable personal protective equipment (PPE) and follow all safety procedures. Failure to follow these instructions will result in death or serious injury.

• Check that the inspection hatch is correctly screwed down.

• Ensure that the power cable is securely fastened by the crimping collar.

• Check that the cover of the charging station is intact and hasn’t suffered any obvious mechanical damage or deformation. b Check that the charging station is securely fastened to the wall.

• Check that nothing is impeding the connection of the charging cable to the Charging station socket.

Configuration

• Check that the Stop Button is unlocked by rotating it 90° clockwise.

Cable Storage

•  DANGER
• HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH Regularly check the integrity of the cable.
• Failure to follow these instructions will result in death or serious injury.
• Ensure that the charging connector and charging cable are securely stored between charging sessions.
• Wrap the charging cable around the charging station’s cable trough.
• If the EVlink Home Charging station and EVlink Home Smart charging station are installed indoors, protect the connector by covering it with the dust cap.
• If the EVlink Home Charging station and EVlink Home Smart charging station are installed outdoors, store the connector by plugging it into the socket of the charging station.

 setup Commissioning App (For EVlink Home Smart Charging Station)

1. Charging Station Configuration With eSetup For Electrician App
2. Commissioning Steps
   • NOTICE
   • FIRMWARE UPGRADE
   • Do not shut down the power during the Firmware upgrade.
   • Failure to follow these instructions can result in equipment damage.
   • The whole Firmware upgrade duration will take 5 to 10 minutes.
   • For your information, eSetup will disconnect from EVlink Home Smart charging station during the process.

Notes :
Refer to privacy notices made available to you in the Wiser application or supervision tool, as applicable.

eSetup PIN Code Reset

• PIN Code reset :
  If eSetup PIN code is lost, refer to eSetup mobile application guideline to do a Pin code reset. The PIN code of eSetup will be reset to 123456.

Operation

Connecting the Electric Vehicle Charging Station

• Connect the charging cable’s plug into the Electric Vehicle charging station’s socket.
• The charge’s indicator LED will change from a constant green to pulsing

Disconnecting the Electric Vehicle

• WARNING RISK OF INJURY
• Do not use brute force to unplug the charging connector from the Electric Vehicle as it is mechanically locked .
• Failure to follow these instructions can result in death, serious injury, or equipment damage. Sure he enraging stain a connector mine tchick the mentor.
• Wind the charging cable around the Electric Vehicle charging station’s winding trough.

Remote Operation with Wiser (For EVlink Home Smart Charging Station)

• Wiser Home lets you add, configure, control and schedule your connected Schneider Electric devices from anywhere.

Reading the full device guide online

• Scan the QR code and choose your language for related market
• for complete information about the device, including operation, configuration and using the product with a Wiser system.

Charging Station Status Indicators

• Note : Charging stations upgraded up to July 2023 breath light green  when not connected to the internet router
• Note : Charging stations commissioned or updated after july 2023 breath green when Wi-Fi for commissioning is activated

Basic Troubleshooting

Connector plugged into Electric Vehicle but not charging, LED illuminated constant green|

• Verify that the connector was inserted properly by unplugging and plugging it back into the Electric Vehicle’s socket.
• Verify the charging sequence by following the procedure described in section “Operation”, page 17.

Connector plugged into Electric Vehicle but not charging, LED illuminated fast blinking blue|

• Verify that you do not have a schedule in progress through the supervision app (only for Smart version) that prevents charging the car.
• Verify that you do not have a schedule in progress through your car that prevents charging the car.
• In case you have installed an anti-tripping device. The anti-tripping device limits the maximum power draw of the EVlink Home charging station and can completely stop the charge to ensure the continuity of the electrical distribution under all conditions. Reduce the home load to have at least 9A current available per phase to restart charging the car.
• Be sure you have enough power in your electricity subscription for charging the car and for the house loads. You probably need to increase the electricity subscription of your electrical installation.

Charging station’s LED illuminated solid orange. (EVlink Home Smart charging station ONLY)|

• Reboot the EVlink Home Smart charging station and wait 10 seconds before energizing it.
• The EVlink Home Smart charging station is not connected to the cloud when using Wi-Fi:
• Verify that you have connected the EVlink Home Smart charging station to a 2.4 GHz Wi-Fi with WPA2 password
• Verify that the SSID and password are correct.
• In case the Wi-Fi signal is too weak: connect the charging station with Ethernet cable, or add a Wi-Fi range extender.

Charging station’s LED illuminated red|

• Verify that the Stop Button isn’t locked by rotating it 90° clockwise to unlock it.
• If not, switch off the power supply to the charging station, unplug the connector from the Electric Vehicle, reconnect the power supply, wait for the charging station to become ready (LED illuminated constant green), before reconnecting the connector to the Electric Vehicle.
• Failing that, check that the power supply is securely wired to the charging station’s PE (Protective Earth) terminal.

Charging station’s LED off| No power supply. Switch off the power supply to the charging station, The charging station is possibly damaged. Please contact Schneider Electric’s Customer Care Centre.

Wireless Feature Declaration

• For Europe (where the CE marking is applicable):
• Hereby, Schneider Electric Industries, declares that this electric vehicle charging station EVlink Home Smart is in compliance with the essential requirements and other relevant provisions of Radio
• Equipment Directives RED 2014/53/EU.
• The EU declaration of conformity for EVlink Home Smart offer (EV22080801) can be downloaded on: se.com/docs.
• Wi-Fi:
  • Operating frequency bands: 2412 MHz – 2472 MHz
  • Maximal RF output power: less than 20 dBm (18.25 dBm)
• For UK:
  • Hereby, Schneider Electric Industries, declares that this electric vehicle charging station EVlink Home Smart is in compliance with the essential requirements and other relevant provisions of Radio
  • Equipment Regulation SI 2017 No. 1206.
  • The UK declaration of conformity for EVlink Home Smart offer (EV22080801-UK) can be downloaded on: se.com/uk/docs.
• Wi-Fi:
  •  Operating frequency bands: 2412 MHz – 2472 MHz
    Maximal RF output power: less than 20 dBm (18.25 dBm)

 Recycle

• The packaging materials from this equipment can be recycled.
• The product and all accessories marked with this symbol are electrical and electronic components that must be disposed of separately from household waste. Please help protect the environment by disposing waste in appropriate containers.
• Thank you for helping to protect the environment.

 Warranty

• Do not open the charging station or remove the cover. Contractual warranty: 18 months.

• Schneider Electric Industries SAS 35, rue Joseph Monier

• CS 30323

• F – 92506 Rueil Malmaison Cedex www.se.com

• © 2023 Schneider Electric – All rights reserved.

• UK Representative Schneider Electric Limited Stafford Park 5

• Telford, TF3 3BL

• United Kingdom

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>