BEGA 50042 Ceiling and Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 50042 Ceiling and Wall Luminaire
Product Information
Product Usage Instructions
Dimensions
Instructions for use
Product Description
Installation
HOW TO USE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50042 Ceiling and Wall Luminaire

BEGA-50042-Ceiling-and-Wall-Luminaire-product

Product Information

The product is a luminaire that requires installation and operation in accordance with national safety regulations. It is recommended to have a qualified electrician perform the installation and commissioning. The manufacturer is not liable for damage caused by improper use or installation. The luminaire is protected against overvoltage according to DIN EN 61547. Additional overvoltage protection components are recommended for further protection.

The luminaire has different models with varying specifications. The models include 50 042 K27 and 50 042 K3. The connected wattage for the lamp module ranges from 26.4 W to 31 W. The rated temperature is between 25°C and 40°C. The colour temperature options are 2700 K and 3000 K, with a colour rendering index (CRI) greater than 90. The module luminous flux ranges from 3845 lm to 3970 lm, and the luminaire luminous flux ranges from 2510 lm to 2592 lm. The luminaire luminous efficiency is between 81 lm/W and 83.6 lm/W.

Product Usage Instructions

Luminaire with trim ring: Before installing onto the mounting surface, insert the luminaire housing into the trim ring (accessory).
During installation or relamping, avoid touching the light output opening of the LED directly.
To release the glass from the luminaire housing, turn it counterclockwise.
The maximum wall mounting height is 2.7 m and the maximum ceiling mounting height is 4.0 m. Metal parts mounted close to the luminaire can affect its range.
Use the integrated push-buttons on the motion sensor to adjust settings. Press the desired push-button to switch to the next level. The LED indicator on the motion sensor will flash to confirm the selection. After reaching the highest level, the level setting starts again from Level 1.
The number of flashes from the LED indicator corresponds to a specific setting. Refer to the manual for details on the number of flashes and their corresponding levels.
Daylight settings are available, but further instructions on how to use them are not provided in the given text.

Ceiling and wall luminaire for indoor use

Dimensions

BEGA-50042-Ceiling-and-Wall-Luminaire-
fig-1

Instructions for use

Application

Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass and metal housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required. Luminaire with motion sensor.

Product Description

Metal housing, finish Colour white Hand-blown opal glass, satin matt, with bayonet closure Integrated HF-motion sensor, maximum range 10 m 2 mounting holes ø 5.5 mm Distance apart 230 mm
2 cable entries for through-wiring for mains cable up to ø 10.5 mm max. 3 × 1.5@ Connection terminal 2.5@ Earth conductor connection
LED power supply unit 230 V y 50 Hz BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire Safety class I
Impact strength IK05
Protection against mechanical
impacts < 0.7 joule
Conformity mark
Weight: 3.2 kg

This product contains light sources of energy efficiency class(es) D, E

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to
the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.

You can find them on our website at www.bega.com

Lamp
- Module connected wattage: 26.4 W
- Luminaire connected wattage: 31 W
- Rated temperature: ta = 25 °C
  Ambient temperature: ta max = 40 °C
50 042 K27
- Color temperature: 2700 K
- Color rendering index: CRI > 90
- Module luminous flux: 3845 lm
- Luminaire luminous flux : 2510 lm
- Luminaire luminous efficiency : 81 lm / W
50 042 K3
- Color temperature: 3000 K
- Color rendering index: CRI > 90
- Module luminous flux: 3970 lm
- Luminaire luminous flux : 2592 lm
- Luminaire luminous efficiency : 83,6 lm / W

Luminaire with trim ring:
Before installing onto the mounting surface the luminaire housing must be inserted into the trim ring (accessory).

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Pass the mains supply cable through the grommet into the luminaire housing.
Fix luminaire housing with enclosed or any other suitable fixing material onto the mounting surface.
It is imperative to use the enclosed gaskets. Dismantle the mains supply cable approx. 60 mm.
Pull silicone sleeves over the wires and make earth and electrical connections to the terminals.
Place glass to the luminaire housing and observe that the cam pins fit into the notches of the glass.
Screw in glass by turning it clockwise. Thus, you reach a safe and vibration-resistant holding of the glass.
To release the glass from the luminaire housing, turn it counterclockwise.

HOW TO USE

BEGA-50042-Ceiling-and-Wall-Luminaire-fig-3

The built-in motion sensor operates at a frequency of 5.8 GHz.
By moving within the detection range the motion sensor switches on the LED module inside the luminaire with a defined dwell time – push-button “Dwell time”.
With a wall mounting height of 1.8 m or ceiling mounting height of 2.6 m, the maximum range is 10 meters (see sketch).

DETECTION RANGE

The max. wall mounting height is 2.7 m and the max. ceiling mounting height is 4.0 m, in which the range reduces significantly. The range can be set individually – push-button “Sensitivity”.

It should be noted that metal parts which are mounted in close proximity to the luminaire can affect the range.

With the three integrated push-buttons (Brightness, Dwell time and Sensitivity) on the motion sensor, specific settings can be made. The first keypress activates the setting function. Press a push-button to switch each function to the next level, the LED indicator on the motion sensor flashes to confirm. After reaching the highest level, the level setting begins with “Level 1”. BEGA-50042-Ceiling-and-Wall-Luminaire-fig-5

BEGA-50042-Ceiling-and-Wall-Luminaire-fig-6

After the 3 parameters brightness, dwell time, and sensitivity have been set successfully the module will require a voltage break to save the changes. The integrated light sensor can be set individually with the brightness levels on the ambient brightness Press the button “Brightness”. Further individual illumination levels can be used with the button “Brightness” and set with the “learning mode”. Press the button “brightness” (> 3 s) to enable the “learning mode”. There is a slow flashing of the LED indicator. After about two minutes, the current brightness value is measured for one minute, the LED flashes faster. After completion, the measured brightness value is saved and is available in stage 6 of “Brightness” as the new brightness value. To simplify the initial operation, the settings have been made as follows:

Range : 75 % (7.5 m)
Dwell time : 10 s
Light sensor : daylight

Factory Reset

The motion sensor can be reset to factory settings (MICAS) by simultaneously pressing the buttons “Sensitivity” and “Dwell time” for about 5 s. The factory settings are as follows:

Range : 75 % (7.5 m)
Dwell time : 900 s
Light sensor : daylight

Test mode

The test mode can be used to check the change of settings of the motion sensor. Press the button “Sensitivity” (> 3 s) to enable the “test mode”. Each further keystroke of this push-button prolongs the test mode. The active test mode is displayed by a flashing of the LED indicator (2 s interval). After 3 minutes the test mode is automatically disabled.

Replacement of the LED unit

The designation of the LED unit is noted on a label in the luminaire.
The light color and light output of BEGA replacement units correspond to those of the LED units originally fitted. The LED unit can be replaced by qualified persons using standard tools.
Disconnect from the main supply.
Unscrew the glass from the luminaire housing by turning it counterclockwise.
Replace the LED unit.
Screw in the glass by turning it clockwise. The defective glass must be replaced.

Accessory · Trim rings

For this luminaire metal trim rings in 3 enamel surfaces are optionally available.
Trim rings are accessories and must be ordered separately.

Part. No