BEGA 34278.2K3 Ceiling and Wall Luminaire Instruction Manual

June 12, 2024
BEGA

BEGA 34278.2K3 Ceiling and Wall Luminaire

Product Information

  • Safety: The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning should only be carried out by a qualified electrician. The manufacturer does not accept liability for damage caused by improper use or installation.
  • Overvoltage Protection: The electronic components installed in the luminaire are protected against overvoltage according to DIN EN 61547. For additional protection against transients, it is recommended to use separate overvoltage protection components, which can be found on the manufacturer’s website at www.bega.com.
  • Lamp Specifications:
    • Lamp Module Connected Wattage: 16W
    • Luminaire Connected Wattage: 19.1W
    • Rated Temperature: 25°C – 35°C
    • Ambient Temperature: Not specified
  • Module Specifications:
    • Module Designation: LED-0569/930
    • Color Temperature: 3000K
    • Colour Rendering Index (CRI): >90
    • Module Luminous Flux: 2440lm
    • Luminaire Luminous Flux: 1587lm
    • Luminaire Luminous Efficiency: 83.1lm/W

Product Usage Instructions

  1. During installation or relamping, avoid touching the light output opening of the LED directly.
  2. To install the glass, place it onto the luminaire housing and ensure that the holding spring bolts fit into the notches of the glass. Turn the glass clockwise until it is locked. This ensures a safe and vibration-resistant holding of the glass.
  3. To remove the glass from the luminaire housing, turn it counterclockwise.

DIMENSION

BEGA-34278-2K3-Ceiling-and-Wall-Luminaire-
FIG-1

Instructions for use

Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass, satin matt and metal housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required.

Product Description

  • Metal housing, finish Colour white aluminum
  • Hand-blown opal glass, satin matt,
  • with sliding-bolt closure
  • 2 mounting holes ø 5.5 mm
  • Distance apart 200 mm
  • 2 cable entries for through-wiring for mains
  • cable up to ø 10,5 mm max. 5 x 1.5@
  • Connecting terminal 2.5@
  • with plug connection
  • Earth conductor connection
  • 2-pole connecting terminal for
  • digital control
  • LED power supply unit
  • 220-240 V x 0/50-60 Hz
  • DC 176-280 V
  • DALI-controllable
  • Number of DALI addresses: 1
  • Basic insulation is provided between the mains
  • and control cables
  • BEGA Thermal Control®
  • Temporary thermal regulation to protect
  • temperature-sensitive components without
  • switching off the luminaire
  • Safety class I
  • Protection class IP 44
  • Protected against granular foreign bodies
  • ≥ 1 mm and splash water
  • Impact strength IK05
  • Protection against mechanical
  • impacts < 0.7 joule
    • r – Safety mark
    • c – Conformity mark
  • Weight: 3.1 kg

This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation.  If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Lamp

  • Module connected wattage 16 W
  • Luminaire connected wattage 19.1 W
  • Rated temperature ta = 25 °C
  • Ambient temperature ta max = 35 °C

34 278.2 K3

  • Module designation LED-0569/930
  • Colour temperature 3000 K
  • Colour rendering index CRI > 90
  • Module luminous flux 2440 lm
  • Luminaire luminous flux 1587 lm
  • Luminaire luminous efficiency 83,1 lm / W

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

  • Disassemble the LED module.
  • Loosen LED connection and earth connection (plug connection).
  • Dismantle the mains supply cable max. 80 mm.
  • Lead mains supply cable through the cable entry into the luminaire housing.
  • Fix the luminaire housing with enclosed or any other suitable fixing material onto the mounting surface.
  • It is imperative to use the enclosed gaskets.
  • Make earth and electrical connections to the terminal.
  • For digital control please use the 2-pole plug connector DA, DA.
  • In case this connector is not used the luminaire will be operated at full light output.
  • Make an earth connection between the LED module and luminaire housing (plug connection).
  • Push LED plugs into couplers as far as it will go.
  • Assemble LED module.
  • Tighten the screws evenly (max. 0,8 Nm). Please observe that the LED module is not damaged mechanically.
  • Insert the opal glass into the luminaire housing with sliding bolt glass closure and turn the glass clockwise up to the stop.
  • Place glass to the luminaire housing and observe that the holding spring bolts fit into the notches of the glass.
  • Turn the glass clockwise until it is locked.
  • Thus, you reach a safe and vibration-resistant holding of the glass.
  • To release the glass from the luminaire housing, turn it counterclockwise.

Replacement of the LED module · Maintenance

  • The designation of the LED module is noted on a label in the luminaire.
  • The light color and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
  • Disconnect the system.
  • Unscrew the glass from the luminaire housing by turning it counterclockwise.
  • Clean glass and luminaire regularly with solvent-free cleansers from dirt.
  • Please follow the installation instructions for the LED module.
  • Screw in the glass by turning it clockwise as far as it will go.
  • A broken glass must be replaced.

Spares

  • Spare glass 11 002 770 .0R G
  • LED power supply unit DEV-0409/700
  • LED module 3000 K LED-0569/930

CONTACT

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals