BRANDMOTION FLTW-3600 Commercial 360Degree SurroundVUE System Instructions

BRANDMOTION FLTW-3600 Commercial 360Degree SurroundVUE System

Product Information

ScrewDriver, Panel Removal Tool, Zip Ties, Socket Set
Install Time| 5 hours – 8 hours and 30 minutes
Kit Contents| 7x Video Harnesses, 3x Power Harnesses, 1x Display Monitor, 1xMonitor Housing, 2x Monitor Housing Mounts, 2x Monitor Housing BasePlates, 1x ECU, 1x Rotary Dial, 4x Camera HDMI, USB, and RemoteAntenna Cords, 1x USB Extension

Recommended Tools

Difficulty Level

Install Time 5hr – 8hr 30m

Kit Contents

• 7x Video Harnesses
• 3x Power Harnesses
• 1x Display Monitor
• 1x Monitor Housing
• 2x Monitor Housing Mounts
• 2x Monitor Housing Base Plates
• 1x ECU
• 1x Rotory Dial
• 4x Camera
• HDMI, USB, and Remote Antenna Cords
• 1x USB Extension

Setting up Head Unit and 360° ECU

1.      Connect the 16-pin Radio Harness to the

vehicle’s factory wiring, following the pinout of your specific vehicle.

Black = Ground

Red = Accessory

*Brown or Pink = Accessory

Yellow = Battery

Orange = Parking Lights (optional) No other wires will be used

2.         Connect 16-pin Display Harness to Display.

3.         Make sure the Head Unit powers on before proceeding. NOTE: Black screen with small box will appear if working properly.

*Brown or Pink: Pink wire is equipped on older models. Brown wire is on new models.

NOTE: This is the reverse wire, it needs to be tapped into Accessory Power. DO NOT tap into factory reverse wire

|

1.        On the Camera Harness, connect Power (yellow), Ground (black), and Accessory (red) to vehicle wiring (See diagram).

2.        Tape up the white wire and RCA cables from Camera Harness.

3.        Attach Camera Harness to 360 ECU.

|

Cameras and Running Wires

1.      According to your specific vehicle, locate and tap into the reverse signal wire and left and right turn signal wires.

2.      Connect Reverse signal and Left and Right turn signal wires to the Red wire at the end of the corresponding camera inputs for each on the Camera Harness.

|

1.      Determine the desired locations for the four cameras. All cameras should be able to see the edge of the vehicle at the bottom part of the field of view.

Front Camera = Top of the grille

Left & Right Camera = Top of the vehicle at

the length midpoint Rear Camera = Top center of the vehicle

2.         Drill 1/4in hole in the vehicle at each proposed camera location to run the wire. NOTE: Check to ensure there is nothing behind your drill location and you can access the other side.

3.         Unscrew the three screws holding the camera within the housing.

NOTE: If you would like to change the exit

location of the camera wire, do that now. You can change the wire exit to the rear of the housing, or the bottom of the housing.

|

Product Usage Instructions

Part 1: Wiring the Display

1. Connect the 16-pin Radio Harness to the vehicle’s factorywiring, following the pinout of your specific vehicle.
   • Black = Ground
   • Red = Accessory
   • Brown or Pink = Accessory
   • Yellow = Battery
   • Orange = Parking Lights (optional)
2. Connect the 16-pin Display Harness to the Display.
3. Make sure the Head Unit powers on before proceeding. Note: Ablack screen with a small box will appear if it is workingproperly.
4. Brown or Pink: Pink wire is equipped on older models. Brownwire is on new models. Note: This is the reverse wire, it needs tobe tapped into Accessory Power. Do not tap into the factory reversewire.

Part 2: Wiring the 360 Harness

1. On the Camera Harness, connect Power (yellow), Ground (black),and Accessory (red) to the vehicle wiring (See diagram).
2. Tape up the white wire and RCA cables from the CameraHarness.
3. Attach the Camera Harness to the 360 ECU.

Part 1: Signal Wires (Left Turn, Right Turn, and Reverse)

1. According to your specific vehicle, locate and tap into thereverse signal wire and left and right turn signal wires.
2. Connect the Reverse signal and Left and Right turn signal wiresto the Red wire at the end of the corresponding camera inputs foreach on the Camera Harness.

Part 2: Mounting the Cameras

1. Determine the desired locations for the four cameras. Allcameras should be able to see the edge of the vehicle at the bottompart of the field of view.
   • Front Camera = Top of the grille
   • Left & Right Camera = Top of the vehicle at the lengthmidpoint
   • Rear Camera = Top center of the vehicle
2. Drill a 1/4 inch hole in the vehicle at each proposed cameralocation to run the wire. Note: Check to ensure there is nothingbehind your drill location and you can access the other side.
3. Unscrew the three screws holding the camera within the housing.Note: If you would like to change the exit location of the camerawire, do that now. You can change the wire exit to the rear of thehousing or the bottom of the housing.

Installing Head Unit and 360 Computer

1. Place the housing base plate either slightly below the drilledhole or have the top hole over top of the drill point, depending onyour camera wire preference. Using two screws, attach the baseplate to the vehicle.

Part 1|
---|---

4.        Place the housing base plate either slightly below the drilled hole or have the top hole over top of the drill point, depending on your camera wire preference. Using two screws attach the base plate to the vehicle.

5.        Run the camera wire through the drilled hole and assemble the camera & housing.

NOTE: The camera has an arrow by the lens, this arrow must be on top. Tighten the three screws to set camera swivel in place.

6.        Run camera extension wires through the vehicle from each camera to the 360 ECU location.

Red Connector = Left Camera Blue Connector = Right Camera Yellow Connector = Rear Camera Black Connector = Front Camera

7.     Connect each camera extension wire to Camera Harness according to color.

|

Installing Product

1.        Connect HDMI cable to the 360 ECU and Display.

2.        Plug 360 Harness into the leftmost slot on 360 ECU, leaving the rightmost 4 pins empty, then the other small 10-pin connector into the Display

3.        Plug in Dial Remote Receiver into the 3.5mm jack. This can be mounted behind the dash with no metal above it.

|
Part 2| Mounting the Display to the Housing
---|---

1. Place the Display within the housing, and screw in from the back using the provided M3 screws.

|

1.      Decide where in the vehicle you would like the display to be mounted, there are three options for the housing to be installed. Each require the connector plate to be screwed in a different location on the housing using the provided plastic biting screws.

On top of the dash

On the front of the dash From the headliner

2.      Once your location is decided, use either the stationary base plate or the swivel base plate. Use the provided long screw and nut

and attached the connector plate to the base plate.

3.      Attach the base plate to your preferred location using 4 screws.

|

1.        Connect the USB outlet to the USB extension from the ECU Harness

2.        Route the USB Outlet wire through the dashboard and into the desired position. NOTE: You can drill a hole (1 5/16in diameter) for the USB Outlet or use the supplied bracket and screws to mount to the dash.

3.        If you are using the supplied bracket, use the desired threaded lock nut to secure the USB Outlet into the supplied bracket housing.

4.        Once you have found your desired position, use the four screws to secure the housing to the dashboard.

|

1.        Clean the back of the knob with alcohol & attach double sided industrial tape

2.        Mount the knob wherever is prefered by the driver. NOTE: the knob battery cover slides off, ensure the mounting orientation is such that the knob slides down onto the cover.

|

Calibration

1.        Create your own calibration mats by cutting 3’ x 3’ squares in a color that contrasts the floor.

2.        Place the interior (vehicle facing) edge of the squares in line with the exterior edge of the vehicle (See Photo). The squares will need to be fully visible on each of the side cameras.

3.        It is recommended to have the mats lay flat during the calibration process to ensure an accurate reading.

4.        Navigate to the “SETTINGS” icon on the far right of the selectable camera perspectives.

5.        Select “Calibration” from the left menu, then select “Edit” next to the Calibration option.

|
Part 2| Digital Calibration
---|---
1.      Select the 4 square calibration mat option

2.      Check the camera images to ensure that two target squares are clearly visible in each image.

3.      Enter the vehicle length and width in centimeters.

4.      Continue entering vehicle measurements in the the calibration menu. When complete, press “Calibration” to advance to the next step.

5.      Auto calibration will occur, but in the case that one of the points fails. Manual splicing will be required, if this is the case follow the prompt to begin the manual calibration process.

|
Part 1| Preparing for Calibration
---|---
6.      Using the touch screen, move each crosshair on each corner of the calibration target. The order should be as shown in the reference image.

7.      When the crosshair is on the corner of the mat, press the “next” icon to highlight the next crosshair. Do this through all locations on each corner and all sides of the vehicle.

8.      Continue through the calibration setup. When finished, press the “Advance” button. Calibration is now complete.

|

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>