BRANDMOTION FLTW-3601 360 Degree System Installation Guide

June 1, 2024
BRANDMOTION

BRANDMOTION FLTW-3601 360 Degree System

BRANDMOTION FLTW-3601 360 Degree System

Recommended Tools

  • Wire Strippers

  • Wire Cutter

  • Electrical Tape
    Recommended Tools

  • Screw Driver

  • Panel Removal Tool

  • Zip Ties

Difficulty Level

Difficulty Level

Install Time

 5hr – 8hr 30m

Questions? Call the Brandmotion technical support line at 734-619-1250 or CLICK HERE

Kit Contents

Components for installing the FLTW-3601

Kit Contents

Kit Contents:

  • 1x Display Monitor
  • 4x Cameras
  • 7x Camera Cables
  • 1x Power/Camera Input Harnesses
  • 1x Monitor Housing
  • 1x USB Extension
  • 1x Rotary Dial
  • 1x Misc Install Supplies

Setting up Head Unit and 360°

Part 1 Wiring the 360 Harness
  1. On the monitor harness, connect 12v constant power (yellow), Ground (black), and Accessory (red) to vehicle wiring. White is not used.
  2. RCA is available for AHD video output from what is on the display.
  3. Plug in Dial Remote Receiver into the 3.5mm jack.
  4. Plug the White Connector into the side of the monitor.

| Setting up Head Unit and 360°

Installing Hardware

Part 1 Signal Wires (Left Turn, Right Turn and Reverse)
  1. According to your specific vehicle, locate and tap into the reverse signal wire and left and right turn signal wires. Run leads up to where the system will be installed.
  2. Connect Reverse signal and Left and Right turn signal wires to the Red wire at the end of the corresponding camera inputs for each on the Harness.

| Installing Hardware
Part 2| Mounting the Housing in the Vehicle

  1. This monitor has two unique mounting options. A fan mount unit, and a threaded 1/4” mounting hole located on the bottom of the bracket.
  2. Choose a desired mounting location on the dashboard to screw the Fan-Bracket in.
  3. Take the monitor and slide in between the Fan-bracket so the holes on the side line up, use the provided screws to secure the monitor.
  4. To use the 1/4” threaded mount, simply thead the bolt into the bottom of the monitor mount.

| Installing Hardware
Part 3| Cameras and Running Wires

  1. Determine the desired locations for the four cameras. About 10% of the screen view should be the vehicle at the bottom part of the field of view.
    Front Camera = Top of the grille
    Left & Right Camera = Top of the vehicle at the length midpoint Rear Camera = Top center of the vehicle

  2. Run camera extension wires through the vehicle from each camera to the 360 Housing location.
    Red Connector = Left Camera
    Blue Connector = Right Camera
    Yellow Connector = Rear Camera Black Connector = Front Camera

  3. Drill 1/4in hole in the vehicle at each proposed camera location to run the wire. Note: Check to ensure there is nothing behind your drill location and you can access the other side.

  4. Run the camera wire through the drilled hole and assemble the camera & housing.
    Note: The camera has an angle adapter plate.
    To angle the camera farther down or up if needed, please place the angle adapter plate between the gasket and the camera body.

  5. Mark and pre-drill the screws that will attach the camera to the vehicle body.

  6. Fasten self screws through the camera body and into the mounting surface (not provided).

  7. Connect each camera extension wire to Camera Harness according to color.

| Installing Hardware
Installing Hardware
Installing Hardware
Part 1| Preparing for Mounting (Rotary Knob)
---|---

  1. Clean the mounting location surface with isopropyl alcohol and attach double sided industrial tape
  2. Mount the knob wherever is prefer ed by the driver. Note: the knob battery cover slides off, ensure the mounting orientation is such that the knob slides down onto the cover.

|

Calibration

Part 1 Preparing for Calibration
  1. Use either the calibration mats, or create your own by cutting four 5’ x 5’ squares in a color that contrasts the floor.
  2. Place a square in each corner of the vehicle about 2’ from front/back and 11’ apart.
  3. It is required to have the mats lay flat during the calibration process to ensure an accurate reading.
  4. This number is a starting baseline and is not an exact requirement.
  5. They can be adjusted as needed in later steps.
  6. It is important that they are in line and parallel with the vehicle.

| Calibration
Part 2| Calibration Setup

  1. Tap on the rightmost arrow icon to show the gear icon.
  2. Tap the gear to enter settings.
  3. In the calibration menu, tap edit.
  4. Tap the leftmost option showing the four squares in the corners of the vehicle.
  5. Make sure you can clearly see all four corners of the squares for both squares in each camera.
  6. If you cant see all the corners, move the square until you can see them. Make sure you move them uniformly.
  7. Tap [Continue] when all squares are clearly visible.

| Calibration
Calibration
Part 3| Vehicle Dimensions

  1. Measure the vehicle length and width in cm.
    Enter those values into the appropriate boxes.
    If the length greater than 610 centimeters, divide the length and width by 1.5 and enter those values. (Length ÷ 1.5 = New Value) and (Width ÷ 1.5 = New Value)

  2. Tap [Calibration]

  3. You will now see a loading indicator for 20 seconds or less

  4. The system will try to  find the squares. It may fail if there is not enough contrast or the background is too busy. This is okay you can manually correct it.

  5. Tap [OK]

  6. Drag each + in the corners of the squares, making sure you follow the pattern:
    Upper Left, Upper Right, Lower Left, and Lower Right.

  7. Repeat for each of the squares on screen to improve calibration.

| Calibration
Calibration
Part 4| Image Adjustments

  1. You may see some distortion of straight lines along the left and right side of the vehicle.
  2. Tap [Advance]
  3. Tap on the side of the vehicle you would like to modify (left shown above)
  4. Adjust the Vertical Centerpoint until the lines straighten out.
  5. Do this for left and right sides.
  6. To straighten the front, tap on the front of the truck and adjust L-gap and R-gap to align
  7. The same can be done for the rear
  8. When you have a calibration you are satisfied with, tap [Save Quit]
  9. Tap [Ok]
  10. The system has been calibrated

| Calibration

Vehicle Application:
Universal
Part Number: FLTW-3601

Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

BRANDMOTION User Manuals

Related Manuals