BRANDMOTION SUTV-2010 SummitView UTV 1080p Rear Vision System Owner’s Manual

June 2, 2024
BRANDMOTION

BRANDMOTION SUTV-2010 SummitView UTV 1080p Rear Vision
System

SUTV-2010 SummitView UTV 1080p Rear Vision System
Owner’s Manual

SUTV-2010 SummitView UTV 1080p Rear Vision System

SummitView™ UTV 1080p Rear Vision System with High Definition 7″ DVR Monitor
SUTV-2010

Recommended Tools

BRANDMOTION SUTV-2010 SummitView UTV 1080p Rear Vision System fig
9

Diffculty Level

BRANDMOTION SUTV-2010 SummitView UTV 1080p Rear Vision System fig
11

BRANDMOTION SUTV-2010 SummitView UTV 1080p Rear Vision System fig
10

Install Time

Product Features

BRANDMOTION SUTV-2010 SummitView UTV 1080p Rear Vision System fig
8

Questions? Call the Brandmotion technical support line at 734-619-1250 or CLICK HERE

Kit Contents

BRANDMOTION SUTV-2010 SummitView UTV 1080p Rear Vision System fig
7

BRANDMOTION SUTV-2010 SummitView UTV 1080p Rear Vision System fig
6

Kit B
Components for installing the Off-Road Camera

Camera Installation

Part 1 Mounting hardware installation

1. Remove the 4 Allen screws that are located on the sides of the camera and remove the camera mounting bracket and visor.
2. Find an appropriate place to mount the camera. Line up the foot bracket to ensure that there is enough space to attach the camera to the body.
3. Attach the mounting foot using either selftapping screws or a bolt and nut.
4. Use a 1” hole saw to drill a hole for the camera harness`| BRANDMOTION
SUTV-2010 SummitView UTV 1080p Rear Vision System fig 5
Part 2| Camera mounting
---|---
1. Feed the harness through the drilled hole, fit the  grommet to the inside of the hole.
2. Reattach camera and visor to the mounting bracket. Make sure the camera is oriented UP by seeing the light sensor on the right side of the camera when looking at it.
3. Route the camera harness to where the diplay is located.
4. Connect the 4-pin to RCA cable to the end of the harness at the display end. (This wont be needed anymore, all connections are 4 pin)| BRANDMOTION
SUTV-2010 SummitView UTV 1080p Rear Vision System fig 4

Monitor Installation and Wiring

Part 1 Roll Bar Mount

1. Choose the proper size roll bar mounting ring.
2. Use supplied foam and apply to the inner ring of the bracket.
3. Place mounting ring on desired location. A fair amount of force might be necessary.
4. Attach the neck of the mounting bracket to the mounting ring, and tighten the cross bolt.
a). Note: If there is still movement in monitor bracket mount, lay 1 to 2 strips of electrical tape between the roll bar and the bracket base.| BRANDMOTION SUTV-2010 SummitView UTV 1080p Rear Vision System fig
3
Part 2| Vehicle Wiring
1. Connect the RED to 12-volt accessory.
2. Connect the BLACK to ground.
3. Connect YELLOW to 12-volt constant power.| BRANDMOTION SUTV-2010
SummitView UTV 1080p Rear Vision System fig 2
Part 3| Camera Wiring
1. Connect the GREEN wire to select parking.
2. Connect the White
3. The BLACK connector is for the power plug.
4. To turn off the guideliness connect the white wire loop on the camera harness.|

FAQ Section

1. How do I stop the monitor mount from moving on the roll cage?****

– We recommend adding a strip of electrical tape to the mounting plate in order to create a tighter fit.

2. How do I turn off the monitor?****

– Hold down the power button for 3 seconds.

3. Is the monitor waterproof?****

– The cameras are rated for IP 69K, however the montior is not waterproof. We recommend mounting it high on the roll bar to prevent the possibility of submerging the unit.

4. What type of battery does the remote use?****

– The remote uses a 2032 3V battery.

WARNING
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
Installation Instructions – UTV Camera System

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

BRANDMOTION User Manuals

Related Manuals