BRANDMOTION SUTV-8837 SummitView Jeep Wrangler Adjustable Rear Vision System Instruction Manual
- June 4, 2024
- BRANDMOTION
Table of Contents
SummitView™ Jeep Wrangler (JK/JL)
Adjustable Rear Vision System
with CMOS Camera For Factory Display SUTV-8837
AR_03_23_21
Installation Instructions – SUTV-8847
Vehicle Application: Jeep Wrangler JK
Part Number: SUTV-8847
Kit Contents
![BRANDMOTION SUTV 8837 SummitView Jeep Wrangler Adjustable Rear Vision System
- fig 2](https://manuals.plus/wp-content/uploads/2022/10/BRANDMOTION-SUTV-8837
-SummitView-Jeep-Wrangler-Adjustable-Rear-Vision-System-fig-2.png) Kit
Contents:
1x CMOS Camera
1x Adjustable 5th Wheel Camera Mount
1x Video Chassis Harness
1x RCA to Factory 22 Pin connector
1x Flash Module
3x Push Nuts
15x Zipties
Programming Instructions
1. PLEASE NOTE: These modules are VIN locked for single-vehicle use. If your
vehicle
ever needs a radio replaced or is flashed by a dealership, you can reprogram
with this programmer.
2. Start the vehicle. Allow it to run for 20-30 seconds before proceeding.
*Failure to start
the vehicle before inserting the programming module can cause catastrophic
failure of the module and void your warranty on this part.
3. Plug module into the OBDII port, located under the dash on the driver’s
side, and wait for the green LED to light up, then remove the module.
4. Shift into reverse. If you get a black/blue screen with “Check your
Surroundings”,
the flash has been successful and you can proceed with testing the camera.|
---|---
Install Rear View Camera
Part 1 | Preparing the Radio |
---|
1. First, you need to gain access to the back of your factory radio. Start by
removing the rubber bin insert from the top of the dash
2. Remove the 7mm bolt under the rubber bin insert.
3. Using a plastic trim removal tool, remove the window switch panel.
4. Disconnect harness from the window switches.
5. Remove the 7mm bolt behind the window switch panel.
6. Remove driver knee bolster cover
7. Remove (2) 7mm bolts on both sides of the steering column.
8. Remove center stack/cluster trim
9. Remove the glove box for access. You will need access to the area behind
the glove box to make your connection to the radio.
10. Remove (4) 7mm bolts to remove radio from dash
11. Locate the White 22 pin connector with a female RCA that was included
with your kit. Plug the 22 pin into the open connection on the back of your
radio.
12. Run the RCA towards the passenger side through the dash and let it rest
behind the glove box. RCA should be visible through the glove box opening.
13. Reassemble the radio and surrounding panels, but leave the glove box
disassembled.|
Part 2| Camera functionality test (Highly recommended, not required)
---|---
1. 8837:
a. There will be three wires accompanying the RCA: Red, Green, and Black
1. Twist red and green together = Power
2. Black = Ground
b. Using a wire extension (not supplied)
1. Connect twisted red and green directly to the positive terminal of the
battery
2. Connect Black to negative terminal of battery
c. Test Camera
1. Connect RCA to Aftermarket radio and
2. Turn Key to on position
3. Place the vehicle in reverse and verify a good image.
2. 8847:
a. There will be two wires at the rear of the
harness near the camera
1. Red= Power
2. Black = Ground
b. Using a wire extension (not supplied)
1. Connect the red wire directly to the positive terminal of the battery
2. Connect Black to the negative terminal of battery
c. Test Camera
3. 8857:
a. There will be two wires accompanying the RCA:
Red and Black
1. Red= Power
2. Black = Ground
b. Using a wire extension (not supplied)
1. Connect the Red wire directly to the positive terminal of the battery
2. Connect Black to the negative terminal of battery
c. Test Camera
1. Connect RCA to Aftermarket radio
2. Turn Key to on position
3. Place the vehicle in reverse and verify a good image.
1. Connect RCA to Aftermarket radio and
2. Turn Key to on position
3. Place the vehicle in reverse and verify a good image.|
Part 3| Installing Rear Camera on Tire Carrier
---|---
1. Remove your spare tire and place the camera bracket on the top two studs.
2. Secure bracket to carrier using (2) push nuts to secure the bracket on two
top studs.
3. The nylon washer will go on the bottom stud and will be secured with the
third push nut.
4. Place your tire on the carrier and make any needed adjustments to the
camera placement to see through the wheel spokes.
5. Once the orientation is satisfactory, tighten two adjustment screws on
bracket.
6. Reinstall the spare tire on the carrier.|
Install Rear View Camera Chassis Harness
1. Using a plastic trim removal tool, remove interior panels on the inside of
the rear gate
2. Insert the camera connector through the rear relief/vent flap behind the
spare tire mount.
DO NOT RUN THROUGH THE CENTER HOLE OF TIRE CARRIER
3. Gently pull the harness through the relief door and connect your camera
harness to your chassis harness.
4. Use supplied wire ties to secure chassis harness to the existing harness
in the tailgate.
5. Use supplied wire ties to secure the chassis harness to the exterior of
fabric factory wire cover connecting tailgate to the body. Do not run through
fabric factory wire cover. CAUTION: Leave enough slack to allow the gate
to open fully
6. Using a plastic trim removal tool, remove rear access (behind seat belt)
panel to expose 10mm bolt, and remove bolt. Failure to remove this bolt will
break the panel.
7. Remove interior rear quarter panel
8. FOR 8848, you will need to ground black wire at a good chassis ground.
Isolate the red wire with electrical tape. You will connect to power at the
front of the vehicle in later steps.
9. Pull back carpet and continue running chassis harness forward under sill
plates and B-pillar cover to passenger kick panel
10. Use a plastic trim removal tool to remove the (2) plastic push pins and
remove passenger sill plate/kick panel.
11. Run the chassis harness behind the glove box and into the radio cavity.|
![BRANDMOTION SUTV 8837 SummitView Jeep Wrangler Adjustable Rear Vision System
- cover](https://manuals.plus/wp-content/uploads/2022/10/BRANDMOTION-SUTV-8837
-SummitView-Jeep-Wrangler-Adjustable-Rear-Vision-System-cover.png)
---|---
Connecting to Power
Part 1|
---|---
1. 8837:
a. There will be three wires accompanying the RCA
in the passenger panel: Red, Green, and Black
1. Twist red and green together = Power
2. Black = Ground
b. Identify power output from your aftermarket radio
c. Connect twisted red and green wire to power output from radio
d. Connect black wire to Chassis ground. We recommend using factory chassis
grounding point.
2. 8847:
a. Identify red power wire exiting the back of the yellow RCA from your camera
chassis harness
b. Identify power output from your aftermarket radio
c. Connect Red wire to power output from your aftermarket radio
d. Connect black wire to Chassis ground. We recommend using factory chassis
grounding point.
3. 8857:
a. Connect jumper power harness to chassis harness (if not already connected)
b. Separate power and ground wires at jumper harness
1. Red = Power
2. Black = Ground
c. Identify power output from your aftermarket radio
d. Connect red wire to power output from your aftermarket radio.
e. Connect black wire to Chassis ground. We recommend using factory chassis
grounding point.|
![BRANDMOTION SUTV 8837 SummitView Jeep Wrangler Adjustable Rear Vision System
- power](https://manuals.plus/wp-content/uploads/2022/10/BRANDMOTION-SUTV-8837 -SummitView-Jeep-Wrangler-Adjustable-Rear-Vision-System-power.png)
Finishing Installation
Part 1|
---|---
a. Connect male RCA of chassis harness to female RCA behind glove box.
b. Test camera
1. Twist red and green together = Power
2. Black = Ground
c. Reassemble vehicle in reverse order of removal|
FAQ Section
WARNING: Cancer and Reproductive Harm
www.P65Warnings.ca.gov
AR_03_23_21
Installation Instructions – SUTV-8847
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>