Brandmotion FLTW-7614 Handle Rear Vision Camera Installation Instruction
- June 3, 2024
- BRANDMOTION
Table of Contents
Brandmotion FLTW-7614 Handle Rear Vision Camera
ITEMS INCLUDED IN THE KIT
- Tailgate Bezel with Camera
- Chassis Harness
- Power Harness
- Instructions
TOOLS & SUPPLIES NEEDED
- Wire Ties
- Electrical Tape or Heat Shrink Tubing
- Plastic Trim Removal Tool
- Soldering Iron & Solder (Recommended)
- Small grommet or Silicone (If needed)
- Vehicle service manual (If needed)
SAFETY PRECAUTIONS
- Work in well ventilated area that is clear of obstructions.
- Secure vehicle with tire chucks in both front and rear of tires.
- Turn vehicle accessories OFF and ensure ignition key is in OFF position.
- Wear safety goggles and snug fitting clothes.
- Use tools only for their intended purpose and which are in good repair.
- Only perform this task if confidence, skill, and physical ability permit.
NOTE: We strive to provide accurate and up-to-date installation instructions.
INSTALLATION
- Disassemble tailgate and remove current tailgate bezel assembly.
- Transfer lock assembly and install new tailgate bezel.
- Route camera harness through the hole in bottom of tailgate. Drill hole if one does not exist. RECOMMENDED: Protect camera harness from any sharp metal edges by applying a small amount of silicone caulk or a rubber grommet.
- Connect camera harness to supplied chassis harness. The optimal location for this junction may occur under rear bumper.
- Wrap connection with electrical tape to ensure tight connection and seal from environment. IMPORTANT: Ensure harnesses moves freely with the tailgate.
- Route chassis harness forward. Zip tie along existing wire harness. Make sure harness does not get pinched and is away from hot or moving components.
- Route chassis harness into truck cab through existing body plug. Drill hole if necessary. RECOMMENDED: Protect Camera Harness from any sharp metal edges by applying a small amount of silicone caulk or a rubber grommet and to seal cab from water.
- Using a vehicle-specific service guide/wiring diagram and a multi-meter, verify 12v reverse or ignition power source. Red wire of power harness connects to 12v+ Ignition or reverse power and black wire of power harness to black chassis ground nut or wire. RECOMMENDED: Solder wires and cover with heat shrink tubing.
- Use wire ties to secure chassis harness up to vehicle display.
- Connect chassis harness male RCA connector to RCA located on your display.
- Coil any excess chassis harness and secure it to existing vehicle wiring with wire ties or electrical tape.
- Test system. Close tailgate and clear all removed items from around the vehicle before starting the vehicle. Next, shift into reverse and check radio display for the camera image.
- Reassemble vehicle. Follow your disassembly steps in reverse order, taking care not to bind the harness wiring when reinstalling trim.
GRIDLINE OPTIONS: The camera’s default setting displays gridlines. To remove the gridline display, connect the two green wires near the end of the Camera Harness. This will remove the gridlines once the camera is repowered.
FAQs
Can you have a Brandmotion FLTW-7614 rear view camera on all the time?
Yes, backup cameras can always be on; all you need are high-quality equipment and knowledgeable installers. Please do not hesitate to contact us if you have any additional questions about backup cameras or if you want to learn more about our solutions.
Where does the Brandmotion FLTW-7614 rear vision camera display what it sees?
The area behind your car is visible in the rearview mirror thanks to a rear- facing camera that is mounted at the back of your car.
What is the difference between a backup camera and a rear view camera?
When you put your car in reverse, a backup camera activates. Rear-view cameras let you see what’s behind your car at any time by turning them on.
Why is Brandmotion FLTW-7614 rear view camera important?
In order to avoid a collision, a reverse camera’s obvious purpose is to be able to view what is behind the vehicle. Reversing into a low wall or round pole might result in costly paintwork damage to your automobile (reversing sensors occasionally overlook these objects).
Does reverse camera work at night?
Despite the fact that many high-end reversing cameras on the market are made to function in a variety of lighting situations, they may nonetheless produce an unobstructed image in almost complete darkness. This is where light emission diodes (LEDs) or infrared night vision lights come in handy.
Does Brandmotion FLTW-7614 rear camera record in parking mode?
To put it simply, parking mode allows your camera to continue to record while you are parked. In contrast to more expensive cameras that have a special parking mode that is activated after a period of inactivity or when the ignition is turned off, the less expensive dash cameras simply stay on and record continuously.
Where is the Brandmotion FLTW-7614 rear view camera located?
Parking mode, to put it simply, enables your camera to keep recording when you are parked. Less expensive dash cameras simply remain on and record continuously, in contrast to more expensive cameras that have a special parking mode that is activated after a period of inactivity or when the ignition is turned off.
Is Brandmotion FLTW-7614 rear camera front or back?
A back-facing camera, also referred to as a rear-facing camera, is located on the back of a smartphone, tablet, or other device and faces away from the user. It is the typical camera on a cell phone and has the same orientation as a regular camera.
Do Brandmotion FLTW-7614 rear view cameras reduce accidents?
According to Insurance Information Institute research, backup cameras cut the risk of collisions by 16%. (with a significant reduction in backup accidents involving drivers over the age of 70).
What is Brandmotion FLTW-7614 rear camera in phone?
A digital camera that is integrated into a smartphone, tablet, or other portable device and has the lens facing away from the user Comparing this to the front-facing camera A collision avoidance system is another option.
Why do Brandmotion FLTW-7614 rear cameras look different?
Wide-angle lenses used by phone cameras distort faces. The back camera is worse because your nose appears to be much larger because it is much closer to your face. This is not how real cameras operate.
Where is the Brandmotion FLTW-7614 rear view camera located?
Rear Vision Camera makes use of a camera that can be seen in the rear of your car, at or near the centerline. In addition to what you can see in your mirrors, the camera is intended to assist in giving you a rear view.
How do you use a Brandmotion FLTW-7614 rear view camera for parking?
Even if it can be useful, your backup camera cannot replace your eyes. You must still utilize your side mirrors and look over your shoulder. The backup camera will turn on automatically when you put the car in reverse. To park the car properly, check the monitor and adhere to the lines.
Can you view Brandmotion FLTW-7614 rear camera while driving?
The reverse gear (designated R) is typically required to turn on the back camera. The camera footage is then instantly displayed on a dashboard panel.
How does a Brandmotion FLTW-7614 rear camera work on a car?
The backup camera automatically comes on when you put your car in reverse. An image of the space behind your automobile can be seen on a video display. Usually, this screen is on the dashboard or in the rearview mirror. In some systems, the image may have distance-indicating lines.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>