BRANDMOTION 9002-7440 License Plate Backup Camera Installation Guide
- June 1, 2024
- BRANDMOTION
Table of Contents
INSTALLATION INSTRUCTIONS
9002-7440 License Plate Backup Camera
Factory Plug in Harness to replace factory tailgate back-up camera Multi Mount
CMOS Camera with Optional Grid Lines and Factory Plug in Harness
(Kit #9002-7440, 9002-7441, 9002-7442, 9002-7443, 9002-7444, 9002-7445,
9002-7446, 9002-7447, 9002-7448, 9002-7449, 9002-7452, 9002-7453)
Please read thoroughly before starting installation and check that kit
contents are complete.
Items Included in the Kit:
- Factory Plug in Harness
- Camera
- Multi mount foot
- License plate mounting bracket
- Mounting screws
- These Instructions
Tools & Supplies Needed:
- ¼” Drill Bit (If Needed)
- Center Punch
- Power Drill
- Wire Ties
- Electrical Tape or Heat Shrink Tubing
- Plastic Trim Removal Tool
- Small grommet or Silicone (If needed)
- Vehicle service manual (If needed)
Safety Precautions:
- Work in well ventilated area that is clear of obstructions.
- Secure vehicle with tire chucks in both front and rear of tires.
- Turn vehicle accessories OFF and ensure ignition key is in OFF position.
- Wear safety goggles and snug fitting clothes.
- Use tools only for their intended purpose and which are in good repair.
- Only perform this task if confidence, skill, and physical ability permit.
NOTE : We strive to provide accurate and up-to-date installation instructions. For the latest full color instructions, as well as an installation video, please visit www.brandmotion.com
Step 1: Select and Install Camera Bracket Determine which of the two supplied camera mounting methods you prefer.
Place camera in desired position to confirm fitment ( Note : Some states
prohibit items blocking the license plate; check local authorities to confirm
legal status for your application).
If using License Plate Bracket, remove license plate. Reattach license plate
securing bracket behind.
If using Alternate Camera Mount Bracket, remove camera from License Plate
Bracket using supplied Allen wrench. Attach camera to the Alternate Camera
Mount bracket and apply supplied self-adhesive foam to mount.
Use the Template included in the Installation Instruction Overview to position
the Alternate Camera Mount on vehicle.
Clean vehicle surface to which mount is to be attached and affix with self-
adhesive foam.
RECOMMENDED: Permanent attachment using screws.
Step 2: Disconnect the harness that leads from the tailgate the under the
back of the bed. There is a different plug and location for each vehicle make.
Step 3: Run the new camera harness through the opening in the back of the
bed to the underside of the vehicle. Step 4: Connect Camera Harness to
supplied Chassis Harness. Make sure to line up the arrows on the connectors.
Tape or heat shrink after to seal connection.
Step 5: Plug the new connector into the factory connector that the
factory camera was just unplugged from. Make sure that the new connector
“clicks” into place.
Step 6: Secure Camera Harness to existing vehicle wiring. This will
minimize the chance of binding or otherwise damaging the harness
Step 7: Test the system. Inspect that all connections are proper and
secure. Clear all loose items removed from the area around the vehicle and
turn ignition key ON to test system.
Step 8: Adjust Camera angle (if necessary). Loosen camera screw to aim
the camera. Tighten screw at desired adjustment.
NOTE : This camera has grid lines or non grid lines and mirror image or
non mirror image options.
Grid line options: Default setting is to display grid lines. To remove
the grid line display, connect the two green wires near the end of the camera
harness.
Display options: Default setting is mirror image display for rearward
facing camera (rear view) installation. To change to non mirror image for
forward facing camera (front view) connect the two white wires near the end of
the camera harness.
FOR TECH SUPPORT CALL
1-734-619-1250
Please have part number available
9002-7440II1.docx