alula RE611P Pet Immune Indoor Motion Sensor User Manual

alula RE611P Pet Immune Indoor Motion Sensor User Manual

he Pet Immune Indoor Motion Sensor alarms when motion is sensed. It is battery powered and requires no installation tools.

Features

• Five year battery life
• Quick peel and press mounting
• Mountable on walls or in corners

Enroll by placing the panel into wireless enrollment mode and then sending an enrollment signal from the sensor. Alternatively, the sensor can be enrolled by entering its 8-character serial number in the AlulaConnect™ portal.

Options for sending an Enrollment Signal

• Remove the battery tab
• Remove the cover to trip the tamper

Install using the included mounting tape to adhere the motion sensor on a wall or in a corner. Alternatively, screw mounting can be done by punching out the screw mounting holes and using the included screws to mount in the desired location.

Installation Tips

• Mount 7.5 feet from the floor.
• Remove the cover before trying to punch out the screw mounting holes.
• It is recommended to ensure there is a tight seal around the mounting holes to prevent bugs from entering the sensor and causing false alarms.

During normal operation the LED will not turn on even if motion is detected. This is done to maximize battery life. Furthermore, when motion is detected and a signal is transmitted to the panel, the sensor will not transmit again for a period of three minutes.

Mounting Screw Holes

**Cover Securing Screws

**

Pro Tips

Walk test mode is entered by removing the battery for 10 seconds and re- inserting the battery. The red LED will begin to flash indicating that the motion sensor is warming up. After 45 seconds, the LED will stop flashing which indicates the motion sensor is ready to detect motion. The LED will illuminate each time motion is detected. Once the LED goes out, the sensor is ready to detect motion again. Walk test mode ends after 15 minutes. It is recommended that the RE611P PIR is tested monthly to ensure proper function.

Mounting tape works great if the surface is properly prepared and firm pressure is applied for over 10 seconds.

Surface Preparation

• Clean the surface
• Ensure the mounting surface temperature is above 50 °F

Motion sensitivity can be adjusted by the sensitivity jumper on the circuit board.

• For standard sensitivity motion detection with pet immunity leave the jumper in the default setting (on).
• Remove the jumper if increased sensitivity to movement is desired.

Pet immunity is optimized when the motion sensor is mounted at 7.5 feet high and aimed away from house features that could allow pets to be high in the detection field (e.g. stairs, counter tops, tall furniture).

Motion catch performance is best when the motion sensor is positioned so a person would typically walk across the front of the motion sensor instead of directly toward the motion sensor.

Motion Detection Tips

• Provide a clear line-of-sight to the monitored area and remember that glass blocks infrared energy (PIR = Passive InfraRed).
• Aim away from windows and sunlight.
• Aim away from air conditioners, heaters or heating/cooling vents.

Specifications

Side field of view for a mounting height of 7.5 feet
Side View

Top field of view
Top View

Physical

Housing Dimensions Weight with Battery Mounting Fastener| 3.5 x 2.5 x 1.8 inches (8.9 x 6.4 x 4.6 cm)3 ounces (85 grams)Mounting Tape or Screws (both provided)
Environmental
Operating Temperature Maximum Humidity| 32°F to 120°F (0°C to 49°C)95% non- condensing relative humidity
Sensor Specifications
Frequency Pet ImmunityReplacement Battery Battery LifeBattery VoltageOptimal Mounting Height Transmitted Indications| 433.92 MHzUp to a maximum of 85 lbs One Panasonic CR123A5 years3.0 VDC (Nominal)7.5 feet (2.3 m)Cover Tamper, Low Battery, Supervision
Certifications
RE611P| FCC, IC

TRADEMARKS
Alula and AlulaConnect are trademarks owned by Alula Holdings, LLC. All trademarks, logos and brand names are the property of their respective owners. All company, product and service names used in this document are for identification purposes only. Use of these names, trademarks and brands does not imply endorsement.

FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference that may be received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Alula could void the user’s authority to operate this equipment.
   FCC ID: XQC-WST740

IC NOTICE
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

IC: 9863B-WST740

47-00035 • Rev A • 2023-05-05
Tech Support Line • (888) 88-ALULA • 888-882-5852
alula.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>